DOWNLOAD Sony XR-CA360EE Service Manual ↓ Size: 1.49 MB | Pages: 31 in PDF or view online for FREE

Model
XR-CA360EE
Pages
31
Size
1.49 MB
Type
PDF
Document
Service Manual
Brand
Device
Car Audio
File
xr-ca360ee.pdf
Date

Sony XR-CA360EE Service Manual ▷ View online

2
XR-CA360EE
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270 ˚C dur-
ing repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
TABLE  OF  CONTENTS
SERVICING  NOTES
...............................................
2
1.
GENERAL
Location of Controls .......................................................
3
Setting the Clock .............................................................
3
2.
DISASSEMBLY
2-1. Disassembly Flow ...........................................................
7
2-2. Sub Panel .........................................................................
7
2-3. Mechanism Deck (MG-36SZ13-32) ...............................
8
2-4. MAIN Board ...................................................................
8
2-5. Heat Sink .........................................................................
9
2-6. Bracket (MD) ..................................................................
9
2-7. DC Motor (Capstan/Reel) (M901) ................................. 10
2-8. Main Belt, Sub Belt (C) .................................................. 10
2-9. Magnetic Head (Playback) (HP901) .............................. 11
3.
MECHANICAL  ADJUSTMENTS
....................... 12
4.
ELECTRICAL  ADJUSTMENTS
......................... 12
Tape Deck Section .......................................................... 12
Tuner Section .................................................................. 13
5.
DIAGRAMS
5-1. Note for Printed Wiring Boards and
Schematic Diagrams ....................................................... 14
5-2. Printed Wiring Board  – MAIN Board – ........................ 15
5-3. Schematic Diagram  – MAIN Board (1/2) – .................. 16
5-4. Schematic Diagram  – MAIN Board (2/2) – .................. 17
5-5. Printed Wiring Board  – CONTROL Board – ................ 18
5-6. Schematic Diagram  – CONTROL Board – ................... 19
5-7. IC Pin Function Description ........................................... 21
6.
EXPLODED  VIEWS
6-1. General Section ............................................................... 23
6-2. Front Panel Section ......................................................... 24
6-3. MAIN Board Section ...................................................... 25
6-4. Mechanism Deck Section (MG-36SZ13-32) ................. 26
7.
ELECTRICAL  PARTS  LIST
............................... 27
SERVICING  NOTES
SERVICE  POSITION
In checking the control board and main board, prepare two jigs
(extension (MD) cord J-2502-060-1 and
connection cable for F/P to main J-2502-072-1).
main board
(CN600)
mechanism deck
main board (CN350)
main board (CN300)
control board (CN900)
connect jig
(connection cable 
for F/P to main J-2502-072-1)
to the main board (CN600) and
control board (CN900).
connect jig
(extention (MD) cord J-2502-060-1)
to the main board (CN300, CN350) 
and mechanism deck.
3
XR-CA360EE
SECTION  1
GENERAL
This section is extracted from
instruction manual.
Location of controls
Refer to the pages listed for details.
XR-CA360EE
SOURCE
MODE
SEL
RELEASE
EQ3
DSPL
ATT
DISC
REP
SHUF
ATA
1
2
3
4
5
6
BTM
OFF
SENS
SEEK
DIR
Setting the clock
The clock uses a 24-hour digital indication.
Example: To set the clock to 10:08
1
Press
(DSPL) for 2 seconds.
The hour indication flashes.
1 Press either side of the volume button
to set the hour.
Press (SEL).
The minute indication flashes.
Press either side of the volume button
to set the minute.
2
  Press 
(DSPL).
The clock starts.
After the clock setting is complete, the
display returns to normal play mode.
to go forward
to go back
to go forward
to go back
qd ATT (attenuate) button
qf Number buttons
During radio reception:
Preset number select
During CD/MD playback:
(1) DISC –
(2) DISC +
(3) REP
(4) SHUF
qg BTM/ATA button
qh SENS button
qj OFF button*
Warning when installing in a car
without ACC (accessory) position on
the ignition key switch
Be sure to press 
(OFF) on the unit for 2
seconds to turn off the clock display after
turning off the engine.
When you press 
(OFF) momentarily, the
clock display does not turn off and this
causes battery wear.
SOURCE (Radio/CD/MD) button
MODE button
During radio reception:
Band select
During CD/MD playback:
CD/MD unit select
Volume +/– button
4
(eject) button
Display window
6
m/M (fast winding)/DIR (tape
transport direction change) buttons
SEEK button
Seek
Automatic Music Sensor
Manual search
DSPL (display mode change) button
EQ3 button
q; RELEASE (front panel release) button
qa SEL (select) button
qs RESET button (located on the front side
of the unit behind the front panel)
4
XR-CA360EE
Notes on speaker connection
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms,
and with adequate power handling capacities to
avoid its damage.
• Do not connect the speaker terminals to the car
chassis, or connect the terminals of the right
speakers with those of the left speaker.
• Do not connect the earth lead of this unit to the
negative (–) terminal of the speaker.
• Do not attempt to connect the speakers in parallel.
• Connect only passive speakers. Connecting active
speakers (with built-in amplifiers) to the speaker
terminals may damage the unit.
• To avoid a malfunction, do not use the built-in
speaker wires installed in your car if the unit shares
a common negative (–) lead for the right and left
speakers.
• Do not connect the unit’s speaker cords to each
other.
Precautions
•Choose the installation location carefully so
that the unit will not interfere with normal
driving operations.
•Avoid installing the unit in areas subject to
dust, dirt, excessive vibration, or high
temperatures, such as in direct sunlight or near
heater ducts.
•Use only the supplied mounting hardware for
a safe and secure installation.
Mount ing angle adjust ment
Adjust the mounting angle to less than 20°.
Removing the protection collar
and the bracket (4)
Before installing the unit, remove the
protection collar 
4 and the bracket 1 from
the unit.
1
Remove the protection collar 4.
1 Engage the release keys 7 together with
the protection collar 4.
2 Pull out the release keys 7 to remove the
protection collar 4.
2
Remove the bracket 1.
1 Insert both release keys 7 together
between the unit and the bracket 1 until
they click.
2 Pull down the bracket 1, then pull up the
unit to separate.
Mounting example (5)
Installation in the dashboard
Notes
• Bend these claws outward for a tight fit, if
necessary (5-2).
• Make sure that the 4 catches on the protection
collar 4 are properly engaged in the slots of the
unit 
(5-3).
A
BUS AUDIO IN
BUS CONTROL IN
AUDIO OUT
REAR
BUS AUDIO IN
BUS CONTROL IN
Source selector*
Селектор источника*
XA-CA30
not supplied
не прилагается
2
B
Cautions
• This unit is designed for negative earth 12 V
DC operation only.
• Do not get the wires under a screw, or caught
in moving parts (e.g. seat railing).
• Before making connections, turn the car
ignition off to avoid short circuits.
• Connect the power connecting cord 6 to the
unit and speakers before connecting it to the
auxiliary power connector.
• Run all earth wires to a common earth
point.
• Be sure to insulate any loose unconnected
wires with electrical tape for safety.
Notes on the power supply cord (yellow)
• When connecting this unit in combination with
other stereo components, the connected car
circuit’s rating must be higher than the sum of
each component’s fuse.
• When no car circuits are rated high enough,
connect the unit directly to the battery.
Connection diagram (3)
To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting
any other system may damage the unit.
Warning
If you have a power aerial without a relay box,
connecting this unit with the power connecting
cord 6 may damage the aerial.
Notes on the control leads
• The power aerial control lead (blue) supplies +12 V
DC when you turn on the tuner.
• When your car has built-in FM/AM aerial in the
rear/side glass, connect the power aerial control
lead (blue) or the accessory power input lead (red)
to the power terminal of the existing aerial
booster. For details, consult your dealer.
• A power aerial without a relay box cannot be used
with this unit.
Memory hold connection
When the yellow power input lead is connected,
power will always be supplied to the memory circuit
even when the ignition switch is turned off.
Caution
Handle the bracket 1 carefully to avoid injuring
your fingers.
1
Catch
Note
Before installing, make sure that the catches on
both sides of the bracket 
1 are bent inwards 2 mm.
If the catches are straight or bent outwards, the unit
will not be installed securely and may spring out.
Connection example (2)
Notes (2-B-
)
• Be sure to connect the earth cord before
connecting the amplifier.
• If you connect an optional power amplifier and do
not use the built-in amplifier, the beep sound will
be deactivated.
Tip (2-B-
)
For connecting two or more CD/MD changers, the
source selector XA-C30 (optional) is necessary.
Mounting the unit in a Japanese
car (6)
You may not be able to install this unit in some
makes of Japanese cars. In such a case, consult
your Sony dealer.
Note
To prevent malfunction, install only with the
supplied screws 
8.
How to detach and attach the
front panel (7)
Before installing the unit, detach the front
panel.
7-A  To detach
Before detaching the front panel, be sure to
press
(OFF).
Press
(RELEASE), then slide the front panel to
the left, and pull it off towards you.
7-B  To attach
Attach part A of the front panel to part B of the
unit as illustrated and push the left side into
position until it clicks.
Warning when installing in a car
without ACC (accessory)
position on the ignition key
switch
Be sure to press 
(OFF) on the unit for 2
seconds to turn off the clock display after
turning off the engine.
When you press 
(OFF) only momentarily, the
clock display does not turn off and this causes
battery wear.
RESET button
When the installation and connections are
completed, be sure to press the RESET button
with a ballpoint pen, etc., after detaching the
front panel.
Power connection diagram
Auxiliary power connector may vary depending
on the car. Check your car’s auxiliary power
connector diagram to make sure the connections
match correctly. There are three basic types
(illustrated below). You may need to switch the
positions of the red and yellow leads in the car
stereo’s power connecting cord.
After matching the connections and switched
power supply leads correctly, connect the unit to
the car’s power supply. If you have any
questions and problems connecting your unit
that are not covered in this manual, please
consult the car dealer.
5
XR-CA360EE
BUS
AUDIO IN
AUDIO
OUT
1
3
5
7
2
4
6
8
5
7
4
8
3
Supplied with XA-C30
Прилагается к модели XA-C30
from car aerial*
от автомобильной
антенны*
Fuse (10 A)
Предохранитель
(10 А)
BUS AUDIO IN
BUS CONTROL IN
RCA pin cord (not supplied)
Шнур с контактными штырьками RCA
(не прилагается)
AUDIO OUT
REAR
See “Power connection diagram” on the reverse side for details.
Подpобнee cм. в paздeлe “Cxeмa подключeния питaния” нa
обpaтной cтоpонe.
AMP REM
from the car’s power connector
к автомобильному разъему
питания
A
Yellow
Желтый
Blue
Голубой
continuous power supply
непрерывное поступление питания
power aerial control
антенная электрика
7
8
4
5
Red
Красный
Black
Черный
switched power supply
включенное питание
earth
земля
Positions 1, 2, 3 and 6 do not have pins.
Позиции 1, 2, 3 и 6 не имеют контактных штырьков.
from the car’s speaker connector
к разъему автомобильного
громкоговорителя
Note for the aerial connecting
If your car aerial is an ISO (International Organisation for Standardisation)
type, use the supplied adaptor 
to connect it.
First connect the car aerial to the supplied adaptor, then connect it to the
aerial jack of the master unit.
*
Примечание о подсоединении антенны
Если антенна в Вашем автомобиле относится к типу, утвержденному ISO
(Международной организацией по стандартизации), используйте для ее
подсоединения переходник 5.
Сначала подсоедините автомобильную антенну к прилагаемому
переходнику, а затем — к антенному гнезду магнитолы.
Source selector
(not supplied)
Селектор источника
(не прилагается)
XA-C30
Supplied with the CD/MD changer
Прилагается к проигрывателю компaкт-диcков/мини-
диcков
1
2
3
4
Negative polarity positions 2, 4, 6, and 8 have striped cords.
Позиции отрицательной полярности 2, 4, 6 и 8 имеют провода с полосками.
Speaker, Rear, Right
Громкоговоритель, задний, правый
Speaker, Rear, Right
Громкоговоритель, задний, правый
Speaker, Front, Right
Громкоговоритель, передний, правый
Speaker, Front, Right
Громкоговоритель, передний, правый
Speaker, Front, Left
Громкоговоритель, передний, левый
Speaker, Front, Left
Громкоговоритель, передний, левый
Speaker, Rear, Left
Громкоговоритель, задний, левый
Speaker, Rear, Left
Громкоговоритель, задний, левый
 Purple
Фиолетовый
White
Белый
Grey
Серый
Green
Зеленый
Blue/white striped
С синей/белой полоской
+
+
+
+
5
6
7
8
5
6
Max. supply current 0.3 A
Макс. сила тока 0,3 А
Auxiliary power connector
Вспомогательный разъем питания
Red
Красный
Yellow
Желтый
4
Yellow
Желтый
switched power supply
включенное питание
Red
Красный
Yellow
Желтый
Red
Красный
continuous power supply
непрерывное поступление питания
7
the car without ACC position
автомобиль не имеет положения АСС
Red
Красный
Yellow
Желтый
Red
Красный
Yellow
Желтый
Red
Красный
Yellow
Желтый
Red
Красный
Yellow
Желтый
4
Yellow
Желтый
continuous power supply
непрерывное поступление питания
Red
Красный
switched power supply
включенное питание
7
Page of 31
Display

Sony XR-CA360EE Service Manual ▷ Download

  • DOWNLOAD Sony XR-CA360EE Service Manual ↓ Size: 1.49 MB | Pages: 31 in PDF or view online for FREE
  • Here you can View online or download the Service Manual for the Sony XR-CA360EE in PDF for free, which will help you to disassemble, recover, fix and repair Sony XR-CA360EE Car Audio. Information contained in Sony XR-CA360EE Service Manual (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.