DOWNLOAD Sony XR-CA360 / XR-CA360X / XRS-CA300 / XRS-CA310X Service Manual ↓ Size: 1.59 MB | Pages: 32 in PDF or view online for FREE

5

BUS

AUDIO IN

AUDIO

OUT

1

4

5

2

6

3

Equipment used in illustrations
(not supplied)
Equipo utilizado en las ilustraciones
(no suministrado)

3

•Choose the installation location carefully so that the unit will not

interfere with normal driving operations.

•Avoid installing the unit in areas subject to dust, dirt, excessive

vibration, or high temperatures, such as in direct sunlight or near
heater ducts.

•Use only the supplied mounting hardware for a safe and secure

installation.

Adjust the mounting angle to less than 20

°

.

Removing the protection collar and the
bracket (4)

Before installing the unit, remove the protection collar 5 and
the bracket 1 from the unit.

Remove the protection collar 5.
1

 Engage the release keys 7 together with the protection collar

5

 .

2

 Pull out the release keys 7 to remove the protection collar 5.

Remove the bracket 1.
1

 Insert both release keys 7 together between the unit and the

bracket until they click.

2

 Pull down the bracket 1, then pull up the unit to separate.

The AM (FM) tuning interval is factory-set to the 9 k (50 k) position.
If the frequency allocation system of your country is based on 10 kHz
(200 kHz) interval, set the switch on the bottom of the unit to the 10 k
(200 k) position before making connections.

Be sure to press (OFF) on the unit for two seconds to turn
off the clock display after turning off the engine.

When you press (OFF) only momentarily, the clock display does not
turn off and this causes battery wear.

When the installation and connections are completed, be sure to
press the RESET button with a ballpoint pen, etc., after detaching the
front panel.

Mounting example (5)

Notes
• Bend these claws outward for a tight fit, if necessary (5-2).
• Make sure that the 4 catches on the protection collar 5 are properly

engaged in the slots of the unit (5-3).

Mounting the unit in a Japanese car (6)

You may not be able to install this unit in some makes of Japanese
cars. In such a case, consult your Sony dealer.

Note
To prevent malfunction, install only with the supplied screws 4.

How to detach and attach the front panel
(7)

7-A To detach

Before detaching the front panel, be sure to press (OFF).
Press (RELEASE), then slide the front panel to the left, and pull it off
towards you.

7-B

Attach part A of the front panel to part B of the unit as illustrated
and push the left side into position until it clicks.

6

5

7

7

c

c

c

1

4

×

×

4

×

×

4

4

×

×

×

×

4

182 mm

53 mm

1

2

5

(OFF)

(RELEASE)

3

B

A

5

6

7

1

7

 Follow the disassembly procedure in the numerical order given.

1

two claws

1

claw

1

two claws

2

sub panel

• This set can be disassembled in the order shown below.

Note 1: The process described in      can be performed in any order.

Note 2: Without completing the process described in      , the next process can not be performed.

Note 3: Illustration of disassembly is omitted.

SET

2-2. SUB PANEL

(Page 7)

FRONT PANEL SECTION

(Note 3)

COVER

(Note 3)

2-3. MECHANISM DECK (MG-36SZ13-32)

(Page 8)

2-4. MAIN BOARD

(Page 8)

2-5. HEAT SINK

(Page 9)

2-6. BRACKET (MD)

(Page 9)

2-7. DC MOTOR 

(CAPSTAN/REEL) (M901)
(Page 10)

2-8. MAIN BELT, 

SUB BELT (C)
(Page 10)

2-9. MAGNETIC HEAD
 

(PLAYBACK) (HP901)
(Page 11)

8

2

two screws
(PTT2.6 

×

 6)

1

connector
(CN350)

1

connector
(CN300)

3

mechanism deck
(MG-36SZ13-32)

2

two screws
(PTT2.6 

×

 6)

2

two ground point screws
(PTT2.6 

×

 6)

3

screw
(PTT2.6 

×

 6)

3

two screws
(PTT2.6 

×

 6)

4

main board

1

claw