DOWNLOAD Sony XR-CA310 / XR-L210 Service Manual ↓ Size: 2.08 MB | Pages: 37 in PDF or view online for FREE

13

1

main belt

4

sub belt (c)

2

screw
(PTP2 

×

 3)

A

2

screw
(PTP2 

×

 3)

2

screw
(PTP2 

×

 3)

2

screw
(PTP2 

×

 3)

3

Lift up the bottom BKT (TS)
in the direction of arrow 

A

(as far as the belt can be removed).

14

Mode

Tension Meter

Meter Reading

Forward

CQ-403A

more than 5.89 mN•m

(more than 60 g)

Reverse

CQ-403R

(more than 2.12 oz)

1. Clean the following parts with a denatured-alcohol-moistened

swab:

playback head

pinch roller

rubber belt

capstan

idler

2. Demagnetize the playback head with a head demagnetizer.
3. Do not use a magnetized screwdriver for the adjustments.
4. The adjustments should be performed with the power supply

voltage (14.4 V) unless otherwise noted.

With this set, it is not necessary to apply suitable locking
compound to the parts after the azimuth adjustment.

Mode

Torque Meter

Meter Reading

2.46 – 5.39 mN•m

Forward

CQ-102C

(25 – 55 g•cm)

(0.35 – 0.76 oz•inch)

Forward

0.15 – 0.39 mN•m

CQ-102C

(1.5 – 4 g•cm)

Back Tension

(0.02 – 0.06 oz•inch)

2.46 – 5.39 mN•m

Reverse

CQ-102RC

(25 – 55 g•cm)

(0.35 – 0.76 oz•inch)

Reverse

0.15– 0.39 mN•m

CQ-102RC

(1.5 –

4 g•cm)

Back Tension

(0.02 – 0.06 oz•inch)

4.91 – 14.70 mN•m

FF, REW

CQ-201B

(50 – 150 g•cm)

(0.69 – 2.08 oz•inch)

This set have the test mode function. In the test mode, FM RDS S-
Meter, FM Auto Seek/Stop Level and MW Auto Seek/Stop Level
adjustments can be performed easier than it in ordinary proce-
dure.

<Set the Test Mode>
1. Turn ON the regulated power supply. (All LEDs on the set

lights up, and the clock is displayed.)

 Press the 

[OFF]

 button, if the clock is not displayed.

2. Push the 

[4]

 button.

3. Push the 

[5]

 button.

4. Press the 

[1]

 button for more than two seconds.

5. Then the display indicates all lights, the test mode is set.

<Release the Test mode>
1. Push the 

[OFF]

 button.

15

0 dB= 0.775 V

1. The adjustments should be performed in the order given in

this service manual.

2. The adjustments should be performed for both L-CH and

R-CH.

Procedure:
1. Put the set into the FWD PB mode.

2. Turn the screw and check the output peak value.  Adjust the

screw  so that the peak value in channels L and R coincides
within 3 dB.

3. Check the phase in the FWD PB mode.

4. Repeat the above adjustment for the REV PB mode.
5. Check that output level difference between FWD PB mode

and REV PB mode is within 4 dB.

Type

 Signal

 Used for

P-4-A063

6.3 kHz, –10 dB

head azimuth adjustment

WS-48A

3 kHz, 0 dB

tape speed adjustment

Adjustment Location: PB head

Procedure:
1. Put the set into the FWD PB mode.
2. Adjust adjustment resistor for inside capstan motor so that the

reading on the frequency counter becomes in 3,015 Hz.

Specified Value: 2,940 to 3,090 Hz

Adjustment Location: See page 18.

Ω

°

°

°

°

Ω

Ω

Ω











16

0 dB=1 

µ

V

When the tuner unit is defective, replace it by a new one be-
cause its internal block is difficult to repair.

Adjust the tuner section in the sequence shown below.

1. FM RDS S-Meter Adjustment
2. FM Auto Seek/Stop Level Adjustment
3. FM Stereo Separation Adjustment
4. MW Auto Seek/Stop Level Adjustment

[SOURCE]

 (CA310) or 

[TUNER]

 (L210) button: FM

Procedure:
1. Set to the test mode. (see page 14)
2. Push the 

[SOURCE]

 (CA310) or 

[TUNER]

 (L210) button and

set to FM.

Display

3. Push the 

[6]

 button.

4. Adjust RV100 on main board so that the display indication is

“8.2”.

Display

Specified Value: Display indication: 8.2 

±

 0.2

Adjustment Location: See page 18.

[SOURCE]

 (CA310) or 

[TUNER]

 (L210) button: FM

Procedure:
1. Set to the test mode. (see page 14)
2. Push the 

[SOURCE]

 (CA310) or 

[TUNER]

 (L210) button and

set to FM.

Display

3. Adjust with the volume RV3 on TU100 so that the “FM” indi-

cation turns to “FM0” indication on the display window.
But, in case of already indicated “FM0”, turn the RV3 so that
put  out light “0” indication and adjustment.

Display

Adjustment Location: See page 18.

µ

Ω

Ω

µ

µ

SHUF

MBP

REG

MBP

SHUF

REG

MBP

SHUF

REG

SHUF

MBP

REG