Sony XR-C8200 Service Manual ▷ View online
– 17 –
Adjustment Location :
Tape speed Adjustment
– SET UPPER VIEW –
RV1 AM Auto Scan/Stop Level Adjustment
RV2 FM Auto Scan/Stop Level Adjustment
RV4 FM Stereo Separation Adjustment
TU11
RV261
RV251
(R-CH)
(L-CH)
Dolby
Level
Adjustment
R-CH
L-CH
L-CH
— SET BOTTOM VIEW —
TP (DOLBY)
Dolby
Level
Adjustment
Dolby
Level
Adjustment
– 18 –
SECTION 6
DIAGRAMS
•
MAIN BOARD IC101
µ
PD78013GC-761-AB8 (TUNER CONTROLLER)
Pin No.
Pin Name
I/O
Function
1
TUNON
O
Tuner system power supply on/off control signal output to the BA3918 (IC601) “H”: tuner on
2
FM ON
O
FM system power supply on/off control signal output to the BA3918 (IC601) “H”: FM on
3 to 8
NCO
O
Not used (open)
9
VSS
—
Ground terminal
10 to 23
NCO
O
Not used (open)
24
VSS
—
Ground terminal
25 to 32
NCO
O
Not used (open)
33
TUNMUT
O
FM and AM signal muting on/off control output “H”: muting on
34
RAMBU
I
35
RESET
I
System reset signal input from the system controller (IC501), reset signal generator (IC551) and
reset switch (S551) “L” is input for several 100 msec after power on, then it changes to “H”
reset switch (S551) “L” is input for several 100 msec after power on, then it changes to “H”
36
NCO
O
Not used (open)
37
BU IN
I
Battery detect signal input from the SONY bus interface (IC571) and battery check circuit
“H”: battery on
“H”: battery on
38
NCO
O
Not used (open)
39
BUSON
I
Bus on/off control signal input from the system controller (IC501) (for SONY bus)
“L”: bus on
“L”: bus on
40
VDD
—
Power supply terminal (+5V)
41
OSCOUT
O
Main system clock output terminal (8 MHz)
42
OSCIN
I
Main system clock input terminal (8 MHz)
43
GND
—
Ground terminal
44
XT OUT
O
Sub system clock output terminal Not used (pull down)
45
XT IN
I
Sub system clock input terminal Not used (fixed at “L”)
46
AVSS
—
Ground terminal (for A/D converter)
47
VSM
I
FM and AM signal meter voltage detection input from the FM/AM tuner unit (TU11)
48
DSTSEL1
I
Destination setting terminal (fixed at “L”)
49
DSTSEL0
I
Destination setting terminal (fixed at “H”)
50
SD IN
I
Station detector detect input from the FM/AM tuner unit (TU11)
Stop level for SEEK, BTM, etc. is determined SD is present at input of “H”
Stop level for SEEK, BTM, etc. is determined SD is present at input of “H”
51
ST MONO
I/O
52 to 54
NIL
I
Not used (fixed at “L”)
55
AVDD
—
Power supply terminal (+5V) (for A/D converter)
56
AVREF
I
Reference voltage input terminal (+5V) (for A/D converter)
57
PLL SI
I
PLL serial data input from the FM/AM PLL (IC91)
58
PLL SO
O
PLL serial data output to the FM/AM PLL (IC91)
59
PLLCKO
O
PLL serial data transfer clock signal output to the FM/AM PLL (IC91)
60
PLLCE
O
PLL serial chip enable output to the FM/AM PLL (IC91)
61
LINKOFF
O
Unilink on/off control signal output (for SONY bus) “L”: link off
62
UNISI
I
Serial data input from the SONY bus interface (IC571)
63
UNISO
O
Serial data output to the SONY bus interface (IC571)
64
UNICKI
I
Serial data reading clock signal input from the system controller (IC501) (for SONY bus)
Input of FM stereo detection signal from FM/AM tuner unit (TU11), and output of forced
monaural control signal to FM/AM tuner unit (TU11) (Commonly used for stereo display input
and forced monaural output)
FM stereo detection at input of “L”, forced monaural at output of “L”
monaural control signal to FM/AM tuner unit (TU11) (Commonly used for stereo display input
and forced monaural output)
FM stereo detection at input of “L”, forced monaural at output of “L”
Internal RAM reset detection signal input from the RN5VD23AA (IC552)
Input terminal to check that RAM data are not destroyed due to low voltage
This checking is made within 100 msec after reset
Input terminal to check that RAM data are not destroyed due to low voltage
This checking is made within 100 msec after reset
6-1.
PIN FUNCTION DESCRIPTION
– 19 –
•
MAIN BOARD IC501
µ
PD78058GC-463-3B9 (SYSTEM CONTROLLER)
Pin No.
Pin Name
I/O
Function
1
RC IN0
I
Rotary remote commander shift key A/D input terminal
2
ILL.IN
I
Dimmer detection signal input Dimmer is present at input of “L”
3
NIL
I
Not used (fixed at “L”)
4
AVSS
—
Ground terminal (for A/D converter)
5
LCDANG
O
Output signal for the LCD view angle adjustment
6
NIL
I
Not used (fixed at “L”)
7
AVREF1
I
Reference voltage (+5V) input terminal (for D/A converter)
8
RE IN0
I
Rotary encoder (RE701) input terminal
9
RE IN1
I
Rotary encoder (RE701) input terminal
10
SUB-CONT1
O
Sub-woofer control signal output
11
SUB-CONT2
O
Sub-woofer control signal output
12
LCDSO
O
Serial data output to the liquid crystal display driver (IC701)
13
LCDCKO
O
Serial data transfer clock signal output to the liquid crystal display driver (IC701)
14
LCDCE
O
Chip enable output to the liquid crystal display driver (IC701)
15
LCDINH
O
Blank indicate control signal output to the liquid crystal display driver (IC701)
“L”: no display
“L”: no display
16
UNISI
I
Serial data input from the SONY bus interface (IC571)
17
UNISO
O
Serial data output to the SONY bus interface (IC571)
18
UNICKI
I
Serial data reading clock signal input terminal (for SONY bus)
19
UNICKO
O
Serial data transfer clock signal output to the tuner controller (IC101) and SONY bus interface
(IC571)
(IC571)
20
BUSON
O
Bus on/off control signal output to the tuner controller (IC101) and SONY bus interface (IC571)
“L”: bus on
“L”: bus on
21
SYSRST
O
Reset signal output to the tuner controller (IC101) and SONY bus interface (IC571) “L”: reset
22
AMPON
O
Standby control signal output to the power amplifier (IC701) “L”: standby
23
—
—
Not used (open)
24
NCO
O
Not used (open)
25
PW ON
O
Main system power supply on/off control signal output to the BA3918 (IC601) “H”: power on
26
ILLON
O
27
COLOR
O
Illumination color selection signal output “H”: amber, “L”: green
28
AMSON
O
Tape auto music sensor control signal output to the CXA2511AQ (IC231)
“L” is output to lower the gain for audio level at FF/REW
“L” is output to lower the gain for audio level at FF/REW
29
REL
I
Reel table rotation detect signal input from the take-up and supply reel sensor
30
MTLIN
I
Auto METAL detect signal input from the METAL detect switch on the mechanism block
31
POS3
I
32
POS2
I
33
GND
—
Ground terminal
34
POS0
I
35
POS1
I
36
LM LOD
O
Loading/tape operation motor control signal output to the LB1638M (IC201)
(For the loading direction and forward side operation) *1
(For the loading direction and forward side operation) *1
37
LM EJ
O
Loading/tape operation motor control signal output to the LB1638M (IC201)
(For the eject direction and reverse side operation) *1
(For the eject direction and reverse side operation) *1
Tape position detect input from the tape operation switch on the mechanism block
Tape position detect input from the tape operation switch on the mechanism block
Power supply on/off control signal output terminal at the illumination and liquid crystal display
driver (IC701) “H”: power on
At power select switch (S501) on mode: “H” output at the accessory on
At power select switch (S501) off mode: “H” output at the power on
driver (IC701) “H”: power on
At power select switch (S501) on mode: “H” output at the accessory on
At power select switch (S501) off mode: “H” output at the power on
– 20 –
Pin No.
Pin Name
I/O
Function
38
N/R OUT
O
Forward/reverse direction control signal output to the CXA2511AQ (IC231)
“H: forward direction, “L”: reverse direction
“H: forward direction, “L”: reverse direction
39
MTLON
O
METAL on/off control signal output to the CXA2511AQ (IC231) “H”: METAL on
40
CM ON
O
Capstan/reel motor (M901) drive signal output terminal “H”: motor on
41
TAPON
O
Tape system power supply on/off control signal output terminal “H”: tape on
42
PW SEL
I
Power select switch (S501) input terminal “L”: off (halt mode), “H”: on (operation mode)
43
RC IN1
I
Rotary remote commander shift key A/D input terminal
44
TEST
I
Setting terminal for the test mode “L”: test mode (normally fixed at “H”)
45
EQSEL
I
Equalizer selection input terminal (fixed at “H”)
46
BEEP
O
Beep sound drive signal output terminal
47
MUT
O
Muting control signal output to the line muting circuit and power amplifier (IC701)
“H”: muting on
“H”: muting on
48
VOLCE
O
Chip enable signal output to the main electrical volume (IC301)
49
SUBCE
O
Chip enable signal output to the sub electrical volume (IC382)
50
VOLCKO
O
Serial data transfer clock signal output to the main electrical volume (IC301)
51
SUBCKO
O
Serial data transfer clock signal output to the sub electrical volume (IC382)
52
VOLSO
O
Serial data output to the main electrical volume (IC301) and sub electrical volume (IC382)
53
TAPMUT
O
Tape muting on/off control signal output to the CXA2511AQ (IC231) “H”: tape muting on
54
DOLON
O
Dolby on/off control signal output to the CXA2511AQ (IC231) “H”: dolby on
55
DOLBC
I/O
56
AMSIN
I
Whether a music is present or not from CXA2511AQ (IC231) is detected at auto music sensor
“L”: music is present, “H”: music is not present
“L”: music is present, “H”: music is not present
57
DIMMER
O
Dimmer control signal output terminal
58
AD ON
O
Power supply on/off control signal output for the A/D converter “L”: power on
59
TIRIND
O
LED drive signal output for the TIR indicator “L”: LED on Not used (open)
60
RESET
I
System reset signal input from the reset signal generator (IC551) and reset switch (S551)
“L” is input for several 100 msec after power on, then it changes to “H”
“L” is input for several 100 msec after power on, then it changes to “H”
61
SIRCS
I
Sircs signal input from the remote control receiver (IC702)
62
BU IN
I
Battery detect signal input from the SONY bus interface (IC571) and battery check circuit
“H”: battery on
“H”: battery on
63
DOORSW
I
Door open/close detect input “L”: door close
64
ACCIN
I
Accessory detect signal input terminal “L”: accessory on
65
NOSESW
I
Detects the removal of the attaching and removing type front panel block “L”: attaching
66
TELMUT
I
Telephone muting signal input terminal At input of “L”, the signal is attenuated by –20 dB
67
KEYACK
I
Input of acknowledge signal for the key entry Acknowledge signal is input to accept function
and eject keys in the power off status On at input of “L”
and eject keys in the power off status On at input of “L”
68
VDD
—
Power supply terminal (+5V)
69
X OUT
O
Main system clock output terminal (5 MHz)
70
X IN
I
Main system clock input terminal (5 MHz)
71
GND
—
Ground terminal
72
XT OUT
O
Sub system clock output terminal (32.768 kHz)
73
XT IN
I
Sub system clock input terminal (32.768 kHz)
74
AVDD
—
Power supply terminal (+5V) (for A/D converter)
75
AVREF0
I
Reference voltage input terminal (+5V) (for A/D converter)
Dolby B/C selection control in/out terminal
At initial mode: dolby B only/dolby B and C type selection input (“L” input: dolby B and C)
At normal mode: dolby type selection signal output to the CXA2511AQ (IC231)
“L”: dolby B, “H”: dolby C
At initial mode: dolby B only/dolby B and C type selection input (“L” input: dolby B and C)
At normal mode: dolby type selection signal output to the CXA2511AQ (IC231)
“L”: dolby B, “H”: dolby C
Click on the first or last page to see other XR-C8200 service manuals if exist.