Sony XR-C7220 / XR-C7300 / XR-C7300W Service Manual ▷ View online
– 37 –
Pin No.
Pin Name
I/O
Function
76
KEYACK
I
Input of acknowledge signal for the key entry Acknowledge signal is input to accept function
and eject keys in the power off status On at input of “H”
and eject keys in the power off status On at input of “H”
77
BU-IN
I
Battery detect signal input from the SONY bus interface (IC701) and battery detect circuit
“L” is input at low voltage
“L” is input at low voltage
78
ILL IN
I
Auto dimmer control illumination line detection signal input terminal
“L” is input at dimmer detection Fixed at “L” in this set
“L” is input at dimmer detection Fixed at “L” in this set
79
TEL-ATT
I
Telephone muting signal input terminal At input of “H”, the signal is attenuated by –20 dB
80
NOSESW
I
Front panel block remove/attach detection switch (S504) input terminal
“L”: front panel is attached
“L”: front panel is attached
81
ACC IN
I
Accessory detect signal input terminal “L”: accessory on
82 to 85
NCO
O
Not used (open)
86
HSTX
I
Hardware standby input terminal “L”: hardware standby mode Reset signal input in this set
87
MD2
I
Setting terminal for the CPU operational mode (fixed at “L” in this set)
88
MD1
I
Setting terminal for the CPU operational mode (fixed at “H” in this set)
89
MD0
I
Setting terminal for the CPU operational mode (fixed at “H” in this set)
90
RESET
I
System reset signal input from the reset signal generator (IC652) and reset switch (S503)
“L”: reset “L” is input for several 100 msec after power on, then it changes to “H”
“L”: reset “L” is input for several 100 msec after power on, then it changes to “H”
91
VSS
—
Ground terminal
92
X0
I
Main system clock input terminal (3.68 MHz)
93
X1
O
Main system clock output terminal (3.68 MHz)
94
VCC
—
Power supply terminal (+5V)
95 to 99
NCO
O
Not used (open)
100
9K/10K
I
Frequency select switch (S502) input terminal
“L”: AM 9 kHz/FM 50 kHz step, “H”: AM 10 kHz/FM 200 kHz step
Used for the XR-C7300/C7300W only
“L”: AM 9 kHz/FM 50 kHz step, “H”: AM 10 kHz/FM 200 kHz step
Used for the XR-C7300/C7300W only
101
NCO
O
Not used (open)
102
NCO
I
Not used (open)
103
AMSIN
I
Whether a music is present or not from CXA2510AQ (IC301) is detected at auto music sensor
“L”: music is present, “H”: music is not present
“L”: music is present, “H”: music is not present
104
REEL
I
Rotation detect signal input from supply reel sensor and take-up reel sensor on the deck
mechanism
mechanism
105
POS0
I
106
POS1
I
107
POS2
I
108
POS3
I
109
LM-EJ
O
Motor drive signal output to the loading/tape operation motor drive (IC361) “H” active
(For the eject direction and reverse side operation) *1
(For the eject direction and reverse side operation) *1
110
LM-LOD
O
Motor drive signal output to the loading/tape operation motor drive (IC361) “H” active
(For the loading direction and forward side operation) *1
(For the loading direction and forward side operation) *1
111
CM-ON
O
Capstan/reel motor (M901) drive signal output terminal “H”: motor on
112
TAPEON
O
Tape system power supply on/off control signal output terminal “H”: tape on
113
N-ROUT
O
Forward/reverse direction control signal output to the CXA2510AQ (IC301)
“L”: forward direction, “H”: reverse direction
“L”: forward direction, “H”: reverse direction
114
AMSON
O
Tape auto music sensor control signal output to the CXA2510AQ (IC301)
“L” is output to lower the gain for audio level at FF/REW mode
“L” is output to lower the gain for audio level at FF/REW mode
115
MTLON
I/O
METAL control in/out terminal
At initial mode: auto/manual mode selection input of METAL function (manual at “L” input)
At manual mode: METAL on/off control signal output to the CXA2510AQ (IC301)
(METAL on at “H” output)
At auto mode: input at MTLIN (pin `⁄‚¤)
At initial mode: auto/manual mode selection input of METAL function (manual at “L” input)
At manual mode: METAL on/off control signal output to the CXA2510AQ (IC301)
(METAL on at “H” output)
At auto mode: input at MTLIN (pin `⁄‚¤)
Tape position (EJECT/FF/REW/
REV/FWD mode) detect input from
the tape operation switch on the deck
mechanism
REV/FWD mode) detect input from
the tape operation switch on the deck
mechanism
POS0: “L”: EJECT mode, “H”: others mode
POS1: “L”: FF and FWD mode, “H”: others mode
POS2: “L”: REW mode, “H”: others mode
POS3: “L”: REV and EJECT mode, “H”: others mode
POS1: “L”: FF and FWD mode, “H”: others mode
POS2: “L”: REW mode, “H”: others mode
POS3: “L”: REV and EJECT mode, “H”: others mode
– 38 –
Pin No.
Pin Name
I/O
Function
116
DOLON
I/O
Dolby control in/out terminal
At initial mode: valid/invalid selection input of dolby function (valid at “L” input)
At normal mode: dolby on/off control signal output to the CXA2510AQ (IC301)
(dolby on at “H” output)
At initial mode: valid/invalid selection input of dolby function (valid at “L” input)
At normal mode: dolby on/off control signal output to the CXA2510AQ (IC301)
(dolby on at “H” output)
117
TAPE MUTE
O
Tape muting on/off control signal output to the CXA2510AQ (IC301) “H”: muting on
Active at ATA, FF/REW mode
Active at ATA, FF/REW mode
118
AMP ON
O
Standby on/off control signal output to the power amplifier (IC611)
“L”: standby mode, “H”: amp on
“L”: standby mode, “H”: amp on
119
VSS
—
Ground terminal
120
POWON
O
Main system power supply on/off control signal output to the BA3918 (IC671) “H”: power on
*1 Loading/tape operation motor control
STOP
LOADING/
FORWARD
EJECT/
REVERSE
BRAKE
LM-LOD (pin `⁄⁄‚)
“L”
“H”
“L”
“H”
LM-EJ (pin `⁄‚·)
“L”
“L”
“H”
“H”
Mode
Terminal
– 39 –
(1)
CHASSIS SECTION
SECTION 7
EXPLODED VIEWS
NOTE:
• -XX and -X mean standardized parts, so they
may have some difference from the original
one.
one.
• Color Indication of Appearance Parts
Example:
KNOB, BALANCE (WHITE) . . . (RED)
KNOB, BALANCE (WHITE) . . . (RED)
↑
↑
Parts Color Cabinet's Color
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Description
Remark
1
3-031-048-01 COLLAR (C7220/C7300)
1
3-031-048-11 COLLAR (C7300W)
2
X-3376-749-1 PANEL ASSY, SUB
3
X-3376-699-1 GEAR ASSY
4
3-027-437-11 DOOR, CASSETTE
5
3-935-003-01 SPRING, TORSION
6
3-031-188-01 BUTTON (EJECT) (
6)
* 7
1-673-172-11 SUB BOARD
8
X-3376-700-1 LOCK ASSY
* 9
3-031-189-01 SHEET, INSULATING
* 10
X-3373-269-1 COVER ASSY (ISO)
11
3-915-923-01 SCREW, GROUND POINT
12
3-012-859-01 CAP (25), RUBBER
13
3-937-650-01 PLATE (C), GROUND
14
1-776-207-72 CORD (WITH CONNECTOR) (POWER)
15
3-935-014-01 CUSHION (U)
* 16
A-3317-359-A MAIN BOARD, COMPLET (C7220)
* 16
A-3317-360-A MAIN BOARD, COMPLET (C7300/C7300W)
* 17
3-031-828-01 BRACKET (REG. IC)
* 18
3-018-390-01 BRACKET (IC)
* 19
3-031-023-01 HEAT SINK
* 20
3-031-049-01 CHASSIS
F801
1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) (10A)
• Items marked “*” are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering
these items.
delay should be anticipated when ordering
these items.
• The mechanical parts with no reference num-
ber in the exploded views are not supplied.
• Hardware (# mark) list and accessories and
packing materials are given in the last of the
electrical parts list.
electrical parts list.
13
12
F801
MG-25G-136
#3
#3
#3
#4
#3
#3
#3
#2
#2
Front panel section
#1
#5
17
11
10
18
14
15
19
16
20
9
3
2
1
8
7
6
4
5
B
B
A
A
– 40 –
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Description
Remark
(2)
FRONT PANEL SECTION
51
3-031-089-01 BUTTON (1-6) (OFF. SHIFT. 1. 2. 3. 4. 5. 6)
52
3-031-093-01 BUTTON (OPEN) (C7220/C7300)
52
3-031-093-11 BUTTON (OPEN) (C7300W)
53
3-935-151-01 SPRING (OPEN)
54
3-031-091-01 BUTTON (D-BASS) (C7220/C7300)
54
3-031-091-11 BUTTON (D-BASS) (C7300W)
55
X-3376-560-1 PANEL SUB ASSY (C7220)
55
X-3376-898-1 PANEL SUB ASSY (C7300)
55
X-3377-199-1 PANEL SUB ASSY (C7300W)
56
3-031-064-01 BUTTON (D/F/D) (+ DISC –. LIST. DSPL)
57
3-031-088-01 BUTTON (M/S) (MODE
*. SOUND)
58
3-031-047-01 LEVER (S/A) (+. –) (C7220/C7300)
58
3-031-047-11 LEVER (S/A) (+. -) (C7300W)
* 59
3-031-326-01 PLATE (A), GROUND
60
1-694-507-11 CONDUCTIVE BOARD, CONNECTION
* 61
3-031-092-01 SHEET (REFLECTOR)
* 62
3-034-309-01 PLATE, LIGHT GUIDE
* 63
3-034-310-01 HOLDER (LCD)
64
3-031-046-01 BUTTON (SOURCE)
65
3-031-045-01 KNOB (VOL) (C7220/C7300W)
65
3-031-045-11 KNOB (VOL) (C7300)
66
3-031-086-01 PLATE (VOL), LIGHT GUIDE
67
X-3376-751-1 PANEL ASSY, FRONT BACK
LCD901 1-803-494-11 DISPLAY PANEL, LIQUID CRYSTAL
#8
not supplied
(KEY board)
(KEY board)
LCD901
#8
67
63
62
61
60
59
57
56
55
54
53
52
51
58
64
65
66
Click on the first or last page to see other XR-C7220 / XR-C7300 / XR-C7300W service manuals if exist.