DOWNLOAD Sony XR-C7200R Service Manual ↓ Size: 568.08 KB | Pages: 40 in PDF or view online for FREE

– 21 –

•

1 to 6

NCO

O

Not used (open)

7

VDD

—

Power supply terminal (+5V)

8

X1

I

Main system clock input terminal (8 MHz)

9

X2

O

Main system clock output terminal (8 MHz)

10

GND

—

Ground terminal

11

XI

I

Sub system clock input terminal    Not used (fixed at “L”)

12

NCO

O

Not used (open)

13

XO

O

Sub system clock output terminal    Not used (open)

14

RESET

I

System reset signal input from the system controller (IC501), reset signal generator (IC551) and
reset switch (S551)       “L” is input for several 100 msec after power on, then it changes to “H”

15

RDSCKI

I

Serial data reading clock signal input from the RDS decoder (IC150)

16

BU IN

I

Battery detect signal input from the SONY bus interface (IC571) and battery check circuit
“H”: battery on

17

BUSON

I

Bus on/off control signal input from the system controller (IC501) (for SONY bus)
“L”: bus on

18

POS3

I

19

POS2

I

20

POS1

I

21

POS0

I

22

NIL

I

Not used (fixed at “L”)

23

MTLIN

I

Auto METAL detect signal input from the METAL detect switch on the mechanism block

24

AMSIN

I

Whether a music is present or not from CXA2510AQ (IC210) is detected at auto music sensor
“L”: music is present, “H”: music is not present

25

TAPIN

I

Not used (fixed at “L”)

26

DOLON

I/O

27

NCO

O

Not used (open)

28

TAPMUT

O

Tape muting on/off control signal output to the CXA2510AQ (IC210)    “H”: tape muting on

29

MTLON

O

METAL on/off control signal output to the CXA2510AQ (IC210)    “H”: METAL on

30

RDSSI

I

Serial data input from the RDS decoder (IC150)

31

NIL

I

Not used (fixed at “L”)

32

CM-ON

O

Capstan/reel motor (M901) drive signal output terminal    “H”: motor on

33

TAP-ON

O

Tape system power supply on/off control signal output terminal    “H”: tape on

34

LMEJ

O

Loading/tape operation motor control signal output to the LB1638M (IC201)
(For the eject direction and reverse side operation)    *1

35

LMLOD

O

Loading/tape operation motor control signal output to the LB1638M (IC201)
(For the loading direction and forward side operation)    *1

36

NIL

I

Not used (fixed at “L”)

37

REEL

I

Reel table rotation detect signal input from the take-up and supply reel sensor

38

PLL-DI

I

PLL serial data input from the FM/AM PLL (IC10)

39

PLL-DO

O

PLL serial data output to the FM/AM PLL (IC10)

40

PLL-CLK

O

PLL serial data transfer clock signal output to the FM/AM PLL (IC10)

41

CE

O

PLL serial chip enable output to the FM/AM PLL (IC10)

42

RQ

O

Communication request signal output to the SONY bus interface (IC571)

43

LINK-OFF

O

Unilink on/off control signal output (for SONY bus)    “L”: link on

Tape position detect input from the tape operation switch on the mechanism block

Dolby control in/out terminal
At initial mode: valid/invalid selection input of dolby function (“L” input: valid)
At normal mode: dolby on/off control signal output to the CXA2510AQ (IC210)
“H”: dolby on

– 22 –

44

SCK

I

Serial data reading clock signal input from the system controller (IC501) (for SONY bus)

45

SI

I

Serial data input from the SONY bus interface (IC571)

46

SO

O

Serial data output to the SONY bus interface (IC571)

47

VDD

—

Power supply terminal (+5V)

48

AVDD

—

Power supply terminal (+5V) (for A/D converter)

49

VREF

I

Reference voltage input terminal (+5V) (for A/D converter)

50 to 52

NIL

I

Not used (fixed at “L”)

53

MUTE-SEL

I

Setting terminal for the muting selection (fixed at “L”)

54

DIST-SEL1

I

Destination setting terminal (fixed at “L”)

55

DIST-SEL0

I

Destination setting terminal (fixed at “L”)

56

S-METER (AM)

I

AM signal meter voltage detection input from the FM/AM tuner unit (TU10)

57

S-METER (FM)

I

FM signal meter voltage detection input from the FM/AM tuner unit (TU10)

58 to 60

NIL

I

Not used (fixed at “L”)

61

MODE2

O

Tuner system power supply on/off control signal output to the BA3918 (IC601)    “H”: tuner on

62

NCO

O

Not used (open)

63

RECEIVE

O

Seek control signal output to the FM/AM tuner unit (TU10)

64

BST-ON

O

Bass-boost control signal output to the power amplifier (IC701)    “H”: bass-boost on

65

MODE1

O

FM system power supply on/off control signal output to the BA3918 (IC601)    “H”: FM on

66

TUNER-MUTE

O

FM and AM signal muting on/off control output    “H”: muting on

67

AF-SEEK

O

AF seek control signal output terminal    Not used (pull down)

68

NCO

O

Not used (open)

69

—

I

Not used (fixed at “H”)

70

ST-IN/MONO

I/O

71

SD-IN

I

Station detector detect input from the FM/AM tuner unit (TU10)
Stop level for SEEK, BTM, etc. is determined    SD is present at input of “H”

72

NCO

O

Not used (open)

73

FWD/REV

O

Forward/reverse direction control signal output to the CXA2510AQ (IC210)
“H: reverse direction, “L”: forward direction

74

AMSON

O

Tape auto music sensor control signal output to the CXA2510AQ (IC210)
“L” is output to lower the gain for audio level at FF/REW

75 to 80

NCO

O

Not used (open)

Input of FM stereo detection signal from FM/AM tuner unit (TU10), and output of forced
monaural control signal to FM/AM tuner unit (TU10)  (Commonly used for stereo display input
and forced monaural output)
FM stereo detection at input of “L”, forced monaural at output of “L”

*1  loading/tape operation motor control

                           MODE

 TERMINAL

LMLOD (pin #∞)

“L”

“H”

“L”

“H”

LMEJ (pin #¢)

“L”

“L”

“H”

“H”

STOP

LOADING/

FORWARD

EJECT/

REVERSE

BRAKE

– 23 –

•

µ

1

RC-IN0

I

Rotary remote commander shift key A/D input terminal

2

ILL-IN

I

Dimmer detection signal input    Dimmer is present at input of “L”

3

NIL

I

Not used (fixed at “L”)

4

AVSS

—

Ground terminal (for A/D converter)

5

LCDANG

O

Output signal for the LCD view angle adjustment

6

NIL

I

Not used (fixed at “L”)

7

AVREF1

I

Reference voltage (+5V) input terminal (for D/A converter)

8

RE IN0

I

Rotary encoder (RE701) input terminal

9

RE IN1

I

Rotary encoder (RE701) input terminal

10

SUB-F

O

Sub-woofer control signal output terminal    Not used (pull down)

11

COLSEL

I

Input terminal to set whether the illumination color change function is present or not
“L”: illumination color change function is present (fixed at “L” in this set)

12

LCDSO

O

Serial data output to the liquid crystal display driver (IC701)

13

LCDCKO

O

Serial data transfer clock signal output to the liquid crystal display driver (IC701)

14

LCDCE

O

Chip enable output to the liquid crystal display driver (IC701)

15

LCDINH

O

Blank indicate control signal output to the liquid crystal display driver (IC701)
“L”: no display

16

UNISI

I

Serial data input from the SONY bus interface (IC571)

17

UNISO

O

Serial data output to the SONY bus interface (IC571)

18

UNICKI

I

Serial data reading clock signal input terminal (for SONY bus)

19

UNICKO

O

Serial data transfer clock signal output to the tuner/tape deck system controller (IC101) and
SONY bus interface (IC571)

20

BUSON

O

Bus on/off control signal output to the tuner/tape deck system controller (IC101) and SONY bus
interface (IC571)    “L”: bus on

21

SYSRST

O

Reset signal output to the tuner/tape deck system controller (IC101) and SONY bus interface
(IC571)    “L”: reset

22

AMPON

O

Standby control signal output to the power amplifier (IC701)    “L”: standby

23, 24

NCO

O

Not used (open)

25

PW-ON

O

Main system power supply on/off control signal output to the BA3918 (IC601)    “H”: power on

26

ILL-ON

O

27

COLOR

O

Illumination color selection signal output    “H”: amber, “L”: green

28

NCO

O

Not used (open)

29 to 32

NIL

I

Not used (fixed at “L”)

33

GND

—

Ground terminal

34, 35

NIL

I

Not used (fixed at “L”)

36 to 39

NCO

O

Not used (open)

40

AD-ON

O

Power supply on/off control signal output for the A/D converter    “L”: power on

41

NCO

O

Not used (open)

42

PW-SEL

I

Power select switch (S501) input terminal
“L”: position A or off (halt mode), “H”: position B or on (operation mode)

43

RC-IN1

I

Rotary remote commander shift key A/D input terminal

44

TEST

I

Setting terminal for the test mode    “L”: test mode (normally fixed at “H”)

45

EQ-SEL

I

Equalizer selection input terminal (fixed at “H”)

46

BEEP

O

Beep sound drive signal output terminal

Power supply on/off control signal output terminal at the illumination and liquid crystal display
driver (IC701)    “H”: power on
At power select switch (S501) on mode: “H” output at the accessory on
At power select switch (S501) off mode: “H” output at the power on

– 24 –

47

MUT

O

Muting control signal output to the line muting circuit and power amplifier (IC701)
“H”: muting on

48

VOLCE

O

Chip enable signal output to the electrical volume (IC301)

49

NCO

O

Not used (open)

50

VOLCKO

O

Serial data transfer clock signal output to the electrical volume (IC301)

51

NCO

O

Not used (open)

52

VOLSO

O

Serial data output to the electrical volume (IC301)

53 to 56

NCO

O

Not used (open)

57

DIMMER

O

Dimmer control signal output terminal

58, 59

NCO

O

Not used (open)

60

RESET

I

System reset signal input from the reset signal generator (IC551) and reset switch (S551)
“L” is input for several 100 msec after power on, then it changes to “H”

61

SIRCS

I

Sircs signal input from the remote control receiver (IC702)

62

BU-IN

I

Battery detect signal input from the SONY bus interface (IC571) and battery check circuit
“H”: battery on

63

DOORSW

I

Door open/close detect input    “L”: door close

64

ACCIN

I

Accessory detect signal input terminal    “L”: accessory on

65

NOSESW

I

Detects the removal of the attaching and removing type front panel block    “L”: attaching

66

TELMUT

I

Telephone muting signal input terminal    At input of “L”, the signal is attenuated by –20 dB

67

KEYACK

I

Input of acknowledge signal for the key entry    Acknowledge signal is input to accept function
and eject keys in the power off status    On at input of “H” (fixed at “H” in this set)

68

VDD

—

Power supply terminal (+5V)

69

OSCOUT

O

Main system clock output terminal (5 MHz)

70

OSCIN

I

Main system clock input terminal (5 MHz)

71

GND

—

Ground terminal

72

XT-OUT

O

Sub system clock output terminal (32.768 kHz)

73

XT-IN

I

Sub system clock input terminal (32.768 kHz)

74

AVDD

—

Power supply terminal (+5V) (for A/D converter)

75

AVREF0

I

Reference voltage input terminal (+5V) (for A/D converter)

76

KEYIN0

I

77

KEYIN1

I

Key input terminal (A/D input)    

6, DSPL, LIST, 10, 9, 8, 7, 6, 5 keys input

(LSW800, LSW711, LSW712 and LSW715 to LSW720)

78

KEYSEL0

I

Setting terminal for the key function select (fixed at “L”)

79

KEYSEL1

I

Setting terminal for the key function select (fixed at “H”)

80

DESTSEL

I

Destination setting terminal (fixed at “L”)

Key input terminal (A/D input)
OFF, SOURCE,  – 

= 0 SEEK/AMS, MODE *, + + ) SEEK/AMS, SOUND,

SHIFT, 1, 2, 3, 4 keys input (LSW700 to LSW710)