DOWNLOAD Sony XR-C6210R / XR-C6220R Service Manual ↓ Size: 3.63 MB | Pages: 44 in PDF or view online for FREE

– 13 –

Mode

Tension Meter

Meter Reading

Forward

CQ-403A

more than 90 g

(more than 3.18 oz)

Reverse

CQ-403R

more than 90 g

(more than 3.18 oz)

1. Clean the following parts with a denatured-alcohol-moistened

swab:

playback head pinch roller
rubber belt

capstan

idlers

2. Demagnetize the playback head with a head demagnetizer.
3. Do not use a magnetized screwdriver for the adjustments.
4. After the adjustments, apply suitable locking compound to the

parts adjusted.

5. The adjustments should be performed with the power supply

voltage unless otherwise noted.

Mode

Torque Meter

Meter Reading

Forward

CQ-102C

30 – 65 g•cm

(0.42 – 0.90 oz•inch)

Forward

CQ-102C

0.5 – 4.5g•cm

Back Tension

(0.01 – 0.06 oz•inch)

Reverse

CQ-102RC

30 – 65 g•cm

(0.42 – 0.90 oz•inch)

Reverse

CQ-102RC

0.5 – 4.5g•cm

Back Tension

(0.01 – 0.06 oz•inch)

FF, REW

CQ-201B

60 – 200 g•cm

(0.83 – 2.78 oz•inch)

This set have the test mode function. In the test mode, FM Auto
Scan/Stop Level and AM (MW) Auto Scan/Stop Level adjustments
can be performed easier than it in ordinary procedure.

<Set the Test Mode>
1. Set the “power select” switch (S501) is “A (ON)” position.
2. Turn ON the regulated power supply. (All LEDs on the set

lights up, and the clock is displayed.)

 Press the 

[OFF]

 button, if the clock is not displayed.

3. Push the preset 

[4]

 button.

4. Push the preset 

[5]

 button.

5. Press the preset 

[1]

 button for more than two seconds.

6. Then the display indicates all lights, the test mode is set.

<Release the Test mode>
1. Push the [OFF] button.
2. Return the “power select” switch (S501) to initially set posi-

tion.

See the adjustment location from on page 16 for the
adjustment.

0 dB=0.775 V

Speed checker

Frequency counter

–1.5 to +2.5%

2,955 to 3,075 Hz

Procedure:
1. Put the set into the FWD PB mode.
2. Adjust adjustment resistor for inside capstan motor so that the

reading on the speed checker or frequency counter becomes in
specification.

Specification: Constant speed

Adjustment Location: See page 16.

set

+

–

test tape
WS-48A
(3 kHz, 0 dB)

AUDIO OUT jack (CNJ151)

10 k

Ω

speed checker

or

frequency counter

– 14 –

0 dB= 1

µ

V

When the tuner unit is defective, replace it by a new one be-
cause its internal block is difficult to repair.

Adjust the tuner section in the sequence shown below.

1. FM Auto Scan/Stop Level Adjustment
2. FM Stereo Separation Adjustment
3. FM RDS S Meter Adjustment
4. AM (MW) Auto Scan/Stop Level Adjustment

[SOURCE]

 button: FM

Procedure:
1. Set to the test mode. (See page 13)
2. Push the 

[SOURCE]

 button and set to FM.

Display

3. Adjust with the volume RV2 on TU1 so that the “FM” indica-

tion turns to “FM0” indication on the display window.
But, in case of already indicated “FM0”, turn the RV2 so that
put  out light “0” indication and adjustment.

Display

Adjustment Location: See page 16.

[SOURCE]

 button: FM

FM Stereo

Level meter

Level meter

signal generator

connection

reading (dB)

output channel

L-CH

L-CH

A

B

R-CH

L-CH

Adjust RV4 on TU1

for minimum reading.

R-CH

R-CH

C

D

L-CH

R-CH

Adjust RV4 on TU1

for minimum reading.

L-CH Stereo separation: A-B
R-CH Stereo separation: C-D
The separations of both channels should be equal.

Specification: Separation more than 30 dB

Adjustment Location: See page 16.

FM RF signal

generator

Carrier frequency

: 98.0 MHz

Output level

: 22 dB (12.6 

µ

V)

Mode

: mono

Modulation

: 1 kHz, 22.5 kHz deviation (30%)

0.01 

µ

F

set

antenna jack (J1)

SHUF

SHUF

FM RF signal

generator

Carrier frequency : 98.0 MHz
Output level

: 70 dB (3.2 mV)

Mode

: stereo

Modulation

: main: 1 kHz, 20 kHz deviation (26.7%)
  sub: 1 kHz, 20 kHz deviation (26.7%)

:

 19 kHz pilot: 7.5 kHz deviation (10%)

0.01 

µ

F

set

antenna jack (J1)

+
–

AUDIO OUT jack (CNJ151)

level meter

10 k

Ω

– 15 –

Make this adjustment after “FM Auto Scan/Stop Level Adjust-
ment”.
Setting:

[SOURCE]

 button: MW

Procedure:
1. Set to the test mode. (See page 13)
2. Push the 

[SOURCE]

 button and set to FM.

3. Push the 

[MODE]

 button and set to MW.

Display

4. Adjust with the volume RV1 on TU1 so that the “MW” indi-

cation turns to “MW0” indication on the display window.
But, in case of already indicated “MW0”, turn the RV1 so that
put out light “0” indication and adjustment.

Display

[SOURCE]

 button: FM

Procedure:
1. Set to the test mode. (See page 13)
2. Push the 

[SOURCE]

 button and set to FM.

Display

3. Push the 

[6]

 button.

4. Adjust RV1 so that the display indication is “10.2”.

Display

Specification: Display indication: 10.0 to 10.4

Adjustment Location: See page 16.

Adjustment Location: See page 16.

FM RF signal

generator

Carrier frequency : 98.00 MHz
Output level

: 35 dB (56.2 

µ

V)

Mode

: mono

Modulation

: no modulation

0.01 

µ

F

set

antenna jack (J1)

SHUF

SHUF

AM RF signal

generator

Carrier frequency : 999 kHz
30% amplitude
modulation by
1 kHz signal
Output level

: 33 dB (44.7 

µ

V)

(50 

Ω

)

set

AM dummy antenna

30 

Ω

15 pF

65 pF

antenna jack (J1)

TP

SHUF

TP

SHUF

– 16 –

– SET  UPPER  VIEW –

Tape Speed Adjustment

TU1

RV1  AM (MW) Auto Scan/Stop Level Adjustment

RV2  FM  Auto Scan/Stop Level Adjustment

RV4  FM  Stereo Separation Adjustment

RV1  FM  RDS S Meter Adjustment