Sony XR-C5080R / XR-C5090R Service Manual ▷ View online
– 34 –
6-5.
IC PIN FUNCTION DESCRIPTION
•
MAIN BOARD IC501 MN1886426SA (SYSTEM CONTROLLER)
Pin No.
Pin Name
I/O
Function
1
TUNMUT
O
FM audio signal muting control output terminal “H”: muting on
2
AMPON
O
Standby control signal output to the power amplifier (IC801) “L”: standby
3
ILLON
O
4
PW ON
O
Main system power supply on/off control signal output to the BA3918 (IC601) “H”: power on
5
AMPMUTE
O
Muting control signal output to the power amplifier (IC801) “L”: muting on
6
RCIN1
I
Rotary remote commander shift key A/D input terminal
7
VDD
—
Power supply terminal (+5V)
8
X IN
I
Main system clock input terminal (8 MHz)
9
X OUT
O
Main system clock output terminal (8 MHz)
10
GND
—
Ground terminal
11
XT IN
I
Sub system clock input terminal (32.768 kHz)
12
XT OUT
O
Sub system clock output terminal (32.768 kHz)
13
EX2
I
Connected to ground
14
RESET
I
System reset signal input from the reset signal generator (IC571) and reset switch (S601)
“L” is input for several 100 msec after power on, then it changes to “H”
“L” is input for several 100 msec after power on, then it changes to “H”
15
RDSCKI
I
Serial data transfer clock signal input from the RDS decoder (IC3)
16
BU IN
I
Battery detect signal input terminal “H”: battery on
17
KEYACK
I
Input of acknowledge signal for the key entry Acknowledge signal is input to accept function
and eject keys in the power off status On at input of “L”
and eject keys in the power off status On at input of “L”
18
VOLSO
O
Serial data output to the electrical volume (IC151)
19
VOLCKO
O
Serial data transfer clock signal output to the electrical volume (IC151)
20
VOLCE
O
Chip enable signal output to the electrical volume (IC151)
21
TAPEMUT
O
Tape muting on/off control signal output to the CXA2509AQ (IC351) “H”: tape muting on
22
LMLOD
O
Loading/tape operation motor control signal output to the MM1322XFBE (IC360)
(For the loading direction and forward side operation) *1
(For the loading direction and forward side operation) *1
23
LMEJ
O
Loading/tape operation motor control signal output to the MM1322XFBE (IC360)
(For the eject direction and reverse side operation) *1
(For the eject direction and reverse side operation) *1
24
AMSON
O
Tape auto music sensor control signal output to the CXA2509AQ (IC351)
“L” is output to lower the gain for audio level at FF/REW
“L” is output to lower the gain for audio level at FF/REW
25
N/R OUT
O
Forward/reverse direction control signal output to the CXA2509AQ (IC351)
“L: forward direction, “H”: reverse direction
“L: forward direction, “H”: reverse direction
26
AMSIN
I
Whether a music is present or not from CXA2509AQ (IC351) is detected at auto music sensor
“L”: music is present, “H”: music is not present
“L”: music is present, “H”: music is not present
27
PLLSO
O
PLL serial data output to the FM/AM PLL (IC1)
28
PLLCKO
O
PLL serial data transfer clock signal output to the FM/AM PLL (IC1)
29
PLLCE
O
PLL serial chip enable output to the FM/AM PLL (IC1)
30
RDSSI
I
Serial data input from the RDS decoder (IC3)
31
AD ON
O
Power supply on/off control signal output for the A/D converter “L”: power on
32
DOLON
I/O
Dolby control in/out terminal
At initial mode: valid/invalid selection input of dolby function (“L” input: valid)
At normal mode: dolby on/off control signal output (“H” output: dolby on)
Not used this function (fixed at “H”)
At initial mode: valid/invalid selection input of dolby function (“L” input: valid)
At normal mode: dolby on/off control signal output (“H” output: dolby on)
Not used this function (fixed at “H”)
Power supply on/off control signal output terminal at the illumination and liquid crystal display
driver (IC901) “H”: power on
At power select switch (S801) on mode: “H” output at the accessory on
At power select switch (S801) off mode: “H” output at the power on
driver (IC901) “H”: power on
At power select switch (S801) on mode: “H” output at the accessory on
At power select switch (S801) off mode: “H” output at the power on
– 35 –
Pin No.
Pin Name
I/O
Function
33
MTLON
I/O
34
CMON
O
Capstan/reel motor (M901) drive signal output terminal “H”: motor on
35
TAPEON
O
Tape system power supply on/off control signal output terminal “H”: tape on
36
ACCON
I
Accessory detect signal input terminal “L”: accessory on
37
PLLSI
I
PLL serial data input from the FM/AM PLL (IC1)
38
BEEP
O
Beep sound output terminal
39
LCDCKO
O
Serial data transfer clock signal output to the liquid crystal display driver (IC901)
40
LCDSO
O
Serial data output to the liquid crystal display driver (IC901)
41
LCDINH
O
Blank indicate control signal output to the liquid crystal display driver (IC901)
“L”: no display
“L”: no display
42
LCDCE
O
Chip enable output to the liquid crystal display driver (IC901)
43
UNICKO
O
Serial data transfer clock signal output to the bus interface (IC701) (for SONY bus)
44
UNICKI
I
Serial data reading clock signal input terminal (for SONY bus)
45
UNISI
I
Serial data input from the bus interface (IC701) (for SONY bus)
46
UNISO
O
Serial data output to the bus interface (IC701) (for SONY bus)
47
VDD
—
Power supply terminal (+5V)
48
AVDD
—
Power supply terminal (+5V) (for A/D converter)
49
AVREF+
I
Reference voltage input terminal (+5V) (for A/D converter)
50
KEYIN1
I
51
KEYIN0
I
52
D-BASS
I
D-BASS switch (SW951) input (A/D input)
53
KEYSEL
I
Setting terminal for the key (XR-C5080R: fixed at center voltage, XR-C5090R: fixed at “H”)
54
DSTSEL
I
Destination setting terminal
AEP, UK models: fixed at “L”, German model: fixed at “H”
AEP, UK models: fixed at “L”, German model: fixed at “H”
55
RCIN0
I
Rotary remote commander shift key A/D input terminal
56
VSM1
I
Signal meter voltage detection input terminal Not used (fixed at “L”)
57
VSM0
I
FM and AM (MW/LW) signal meter voltage detection input from the FM/AM tuner unit (TU1)
58
AVREF–
I
Reference ground terminal
59
AVSS
—
Ground terminal (for A/D converter)
60
GND
—
Ground terminal
61
BUSON
O
Bus on/off control signal output to the bus interface (IC701) (for SONY bus) “L”: bus on
62
SYSRST
O
Reset signal output to the bus interface (IC701) (for SONY bus) “L”: reset
63
SEKOUT
O
Seek control signal output to the FM/AM tuner unit (TU1)
64
TUNON
O
Tuner system power supply on/off control signal output to the BA3918 (IC601) “H”: tuner on
65
FM ON
O
FM system power supply on/off control signal output to the BA3918 (IC601) “H”: FM on
66
MUT
O
Line muting control signal output terminal “H”: line muting on
67
AF SEK
O
AF seek control signal output terminal Not used (open)
68
COLOR
I
Setting terminal for the illumination color “L”: amber, “H”: green Not used (open)
69
NOSESW
I
Detects the removal of the attaching and removing type front panel block “L”: attaching
Key input terminal (A/D input)
OFF, SOURCE, MODE
OFF, SOURCE, MODE
*, + ) + SEEK AMS, – = 0 SEEK AMS, VOLUME –,
SEL, VOLUME +, DSPL, ATT , BTM SENS keys input (LSW901 to LSW910)
Key input terminal (A/D input)
6, INTRO 1, REPEAT 2, SHUF 3, BL SKIP 6, ATA 5, 4, FILE, AF/TA, PRESET DISC +/–,
DSPL keys input (LSW921 to LSW932)
6, INTRO 1, REPEAT 2, SHUF 3, BL SKIP 6, ATA 5, 4, FILE, AF/TA, PRESET DISC +/–,
DSPL keys input (LSW921 to LSW932)
METAL control in/out terminal
At initial mode: valid/invalid selection input of METAL function (“L” input: valid)
At normal mode: METAL on/off control signal output (“H” output: METAL on)
Not used this function (fixed at “H”)
At initial mode: valid/invalid selection input of METAL function (“L” input: valid)
At normal mode: METAL on/off control signal output (“H” output: METAL on)
Not used this function (fixed at “H”)
– 36 –
*1 loading/tape operation motor control
MODE
TERMINAL
LMLOD (pin @™)
“L”
“H”
“L”
“H”
LMEJ (pin @£)
“L”
“L”
“H”
“H”
STOP
LOADING/
FORWARD
EJECT/
REVERSE
BRAKE
Pin No.
Pin Name
I/O
Function
70
ST IN
I/O
71
SD IN
I
Station detector detect input from the FM/AM tuner unit (TU1)
Stop level for SEEK, BTM, etc. is determined SD is present at input of “H”
Stop level for SEEK, BTM, etc. is determined SD is present at input of “H”
72
REL T
I
Reel table rotation detect signal input from the take-up and supply reel sensor
73
POS3
I
74
POS2
I
75
POS1
I
76
POS0
I
77
PW SEL
I
Power select switch (S801) input terminal
“L”: position A (halt mode), “H”: position B (operation mode)
“L”: position A (halt mode), “H”: position B (operation mode)
78
TELEMUTE
I
Telephone muting signal input terminal
At input of “L”, the signal is attenuated by –20 dB Not used (fixed at “H”)
At input of “L”, the signal is attenuated by –20 dB Not used (fixed at “H”)
79
TEST
I
Setting terminal for the test mode “L”: test mode (normally fixed at “H”)
80
ILLIN
I
Not used (fixed at “L”)
Tape position detect input from tape operation switch on the mechanism block
Input of FM stereo detection signal from FM/AM tuner unit (TU1), and output of forced
monaural control signal to FM/AM tuner unit (TU1) (Commonly used for stereo display input
and forced monaural output)
FM stereo detection at input of “L”, forced monaural at output of “L”
monaural control signal to FM/AM tuner unit (TU1) (Commonly used for stereo display input
and forced monaural output)
FM stereo detection at input of “L”, forced monaural at output of “L”
– 37 –
SECTION 7
EXPLODED VIEWS
• Items marked “*” are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering
these items.
delay should be anticipated when ordering
these items.
• The mechanical parts with no reference num-
ber in the exploded views are not supplied.
• Hardware (# mark) list and accessories and
packing materials are given in the last of the
electrical parts list.
electrical parts list.
NOTE:
• -XX and -X mean standardized parts, so they
may have some difference from the original
one.
one.
• Color Indication of Appearance Parts
Example:
KNOB, BALANCE (WHITE) . . . (RED)
KNOB, BALANCE (WHITE) . . . (RED)
↑
↑
Parts Color Cabinet's Color
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Description
Remark
(1) CHASSIS SECTION
1
4
5
6
7
9
14
19
15
3
2
#2
#2
#3
#8
#4
#4
#2
#2
F201
MG-25G-136
#1
Front panel ass’y
10
18
8
12
11
13
16
17
1
3-009-294-01 PANEL, SUB
2
3-935-003-01 SPRING, TORSION
3
3-932-205-21 DOOR, CASSETTE
4
X-3367-636-1 LOCK ASSY
* 5
3-009-306-01 SHEET, INSULATING
* 6
A-3313-472-A MAIN BOARD, COMPLETE
(XR-C5090R: AEP, UK)
* 6
A-3313-473-A MAIN BOARD, COMPLETE
(XR-C5090R: German)
* 6
A-3313-481-A MAIN BOARD, COMPLETE
(XR-C5080R: AEP, UK)
* 6
A-3313-482-A MAIN BOARD, COMPLETE
(XR-C5080R: German)
7
3-915-923-01 SCREW, GROUND POINT
* 8
X-3373-269-1 COVER ASSY (ISO)
9
3-012-859-01 CAP (25), RUBBER
* 10
3-018-798-01 BRACKET (IC)
* 11
3-018-613-01 HEAT SINK
12
3-935-014-01 CUSHION (U)
* 13
3-009-813-01 CHASSIS
14
3-937-650-01 PLATE (C), GROUND
* 15
A-3313-456-A POWER BOARD, COMPLETE
16
1-782-092-11 CORD (WITH CONNECTOR) (ISO-P) (POWER)
17
1-782-093-11 CORD (WITH CONNECTOR) (ISO-S) (SPEAKER)
18
1-777-989-21 CORD (WITH CONNECTOR) (AMP REM)
* 19
3-019-148-01 BRACKET (HS) (M)
F801
1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) (10A)
Click on the first or last page to see other XR-C5080R / XR-C5090R service manuals if exist.