DOWNLOAD Sony XR-C440 / XR-C450 / XR-C450W / XR-P600C Service Manual ↓ Size: 5.17 MB | Pages: 43 in PDF or view online for FREE

– 17 –

1

Fit the lever (LDG-A) on
shafts 

A

 – 

C

 and install it.

shaft 

A

shaft 

C

4

type-E stop ring 2.0

shaft 

A

shaft 

B

3

Align hole in the gear (LDG-D)
with hole the lever (LDG-A).

gear (LDG-FB)

hole

gear (LDG-D)

lever (LDG-A)

2

Move the lever (LDG-B)
in the arrow direction.

1

tension spring (lever LDG)

5

gear (LDG-FT)

5

polyethyene washer

hole

shaft 

B

3

Fit the lever (LDG-B) on
shafts 

A

 and 

B

 and

install it.

2

Pull the lever in the
arrow direction.

– 18 –

2

guide (C)

1

three claws

– 19 –

This set have the test mode function. In the test mode, FM Auto
Scan/Stop Level and AM (MW) Auto Scan/Stop Level adjustments
can be performed easier than it in ordinary procedure.

<Set the Test Mode>
1. Set the “OFF” mode.
2. Push the preset 4 button.
3. Push the preset 5 button.
4. Press the preset 1 button for more than two seconds.
5. Then the display indicates all lights, the test mode is set.

<Release the Test mode>
1. Push the “OFF” button.

1. Clean the following parts with a denatured-alcohol-moistened

swab:

playback head

pinch roller

rubber belt

capstan

idles

2. Demagnetize the playback head with a head demagnetizer.
3. Do not use a magnetized screwdriver for the adjustments.
4. After the adjustments, apply suitable locking compound to the

parts adjusted.

5. The adjustments should be performed with the power supply

voltage unless otherwise noted.

•

Forward

CQ-403A

more than 90 g

(more than 3.18 oz)

Reverse

CQ-403R

more than 90 g

(more than 3.18 oz)

•

Forward

CQ-102C

30 - 65 g·cm

(0.42 - 0.90 oz·inch)

Forward

CQ-102C

0.5 - 4.5g·cm

Back Tension

(0.01 - 0.06 oz·inch)

Reverse

CQ-102RC

30 - 65 g·cm

(0.42 - 0.90 oz·inch)

Reverse

CA-102RC

0.5 - 4.5g·cm

Back Tension

(0.01 - 0.06 oz·inch)

FF, REW

CQ-201B

60 - 200 g·cm

(0.83 - 2.78 oz·inch)

– 20 –

When the tuner unit is defective, replace it by a new one because
its internal block is difficult to repair.

SOURCE button

: FM

FREQUENCY SELECT switch : 10 k

µ

µ

Procedure:
1. Set to the test mode. (See page 19).
2. Push the SOURCE button and set to FM.

Display

FM

SHUF1

3. Push the preset 3 button.

Display

FM

SHUF1

4. Adjust with the volume RV2 on TU1 so that the “FM” indica-

tion turns to “FM0” indication on the display window.
But, in case of already indicated “FM0”, turn the RV2 so that
put  out light “0” indication and adjustment.

Display

Adjustment Location: See page 22.

SHUF1

Procedure:
1. Put the set into the FWD PB mode.
2. Adjust RV231 (L-CH) and RV131 (R-CH) so that the level meter

reading is –6±0.5 dB (0.37 to 0.41 V).

Adjustment Location: See page 22.

See the adjustment location from on page 22 for the ad-
justment.

Procedure:
1. Put the set into the FWD PB mode.

Ω

–1.5 to +2.5%

2,955 to 3,075Hz

Specification: Constant speed

Adjustment Location: See page 22.

Preset 3 (DOLBY) button

: OFF

SEL (BAS) button

: Center

SEL (TRE) button

: Center

SEL (BAL) button

: Center

SEL (FAD) button

: Center

SEL (VOL) button

: Maximum

D-BASS control

: OFF







7

@¢