Sony XR-C2200 / XR-C2300X Service Manual ▷ View online
MICROFILM
SERVICE MANUAL
FM/AM CASSETTE CAR STEREO
US Model
Canadian Model
SPECIFICATIONS
XR-C2200/C2300X
Model Name Using Similar Mechanism
NEW
Tape Transport Mechanism Type
MG-36SZ10-32
Photo: XR-C2200
AUDIO POWER SPECIFICATIONS (US model)
POWER OUTPUT AND TOTAL HARMONIC DISTORTION
19 watts (for XR-C2300X)/18 watts (for XR-C2200) per channel
minimum continuous average power into 4 ohms, 4 channels
driven from 20 Hz to 20 kHz with no more than 1 % total
harmonic distortion.
19 watts (for XR-C2300X)/18 watts (for XR-C2200) per channel
minimum continuous average power into 4 ohms, 4 channels
driven from 20 Hz to 20 kHz with no more than 1 % total
harmonic distortion.
Other specifications
Cassette player section
Tape track
4-track 2-channel stereo
Wow and flutter
0.13 % (WRMS)
Frequency response
30 – 15,000 Hz
Signal-to-noise ratio
55 dB
Tuner section
FM
Tuning range
87.5 – 107.9 MHz
Antenna terminal
External antenna connector
Intermediate frequency
10.7 MHz
Usable sensitivity
9 dBf
Selectivity
75 dB at 400 kHz
Signal-to-noise ratio
65 dB (stereo),
68 dB (mono)
68 dB (mono)
Harmonic distortion at 1 kHz
0.7 % (stereo),
0.4 % (mono)
0.4 % (mono)
Separation
35 dB at 1 kHz
Frequency response
30 – 15,000 Hz
AM
Tuning range
530 – 1,710 kHz
Antenna terminal
External antenna connector
Intermediate frequency
10.7 MHz/450 kHz
Sensitivity
30
µ
V
Power amplifier section
Outputs
Speaker outputs
(sure seal connectors)
(sure seal connectors)
Speaker impedance
4 – 8 ohms
Maximum power output XR-C2300X:
50 W
×
4 (at 4 ohms)
XR-C2200:
45 W
45 W
×
4 (at 4 ohms)
General
Outputs
Audio output
Power antenna relay
control lead
Power amplifier control
lead
Power antenna relay
control lead
Power amplifier control
lead
Tone controls
Bass
±
8 dB at 100 Hz
Treble
±
8 dB at 10 kHz
Power requirements
12 V DC car battery
(negative ground)
(negative ground)
Dimensions
Approx. 188
×
58
×
182 mm
(7
1
/
2
×
2
3
/
8
×
7
1
/
4
in.)
(w/h/d)
Mounting dimensions
Approx. 182
×
53
×
163 mm
(7
1
/
4
×
2
1
/
8
×
6
1
/
2
in.)
(w/h/d)
Mass
Approx. 1.2 kg (2 lb 10 oz)
Supplied accessories
Parts for installation and
connections (1 set)
Front panel case (1)
connections (1 set)
Front panel case (1)
Design and specifications are subject to change
without notice.
without notice.
2
TABLE OF CONTENTS
1.
GENERAL
Location of Controls .......................................................
3
Setting the Clock .............................................................
3
Installation .......................................................................
4
Connections .....................................................................
5
2.
DISASSEMBLY
.........................................................
7
3.
MECHANICAL ADJUSTMENTS
....................... 10
4.
ELECTRICAL ADJUSTMENTS
Test Mode ........................................................................ 10
Tape Deck Section .......................................................... 10
Tuner Section .................................................................. 12
Tape Deck Section .......................................................... 10
Tuner Section .................................................................. 12
5.
DIAGRAMS
5-1. Note for Printed Wiring Boards and
Schematic Diagrams ....................................................... 14
5-2. Printed Wiring Board – MAIN Board – ......................... 15
5-3. Schematic Diagram – MAIN Board (1/2) – ................... 16
5-4. Schematic Diagram – MAIN Board (2/2) – ................... 17
5-5. Printed Wiring Board – KEY Board – ........................... 18
5-6. Schematic Diagram – KEY Board – .............................. 19
5-7. IC Pin Function Description ........................................... 21
5-3. Schematic Diagram – MAIN Board (1/2) – ................... 16
5-4. Schematic Diagram – MAIN Board (2/2) – ................... 17
5-5. Printed Wiring Board – KEY Board – ........................... 18
5-6. Schematic Diagram – KEY Board – .............................. 19
5-7. IC Pin Function Description ........................................... 21
6.
EXPLODED VIEWS
................................................ 23
7.
ELECTRICAL PARTS LIST
............................... 26
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270 ˚C dur-
ing repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-
• Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
3
SECTION 1
GENERAL
This section is extracted from
instruction manual.
instruction manual.
Location of controls
Refer to the pages listed for details.
1 MENU button 7, 9, 10, 11, 13
2 Volume control dial
3 SOURCE (TUNER/CD/MD) button
9, 10, 12
4 PRST/DISC +/– (cursor up/down) buttons
7, 9, 10, 11, 13
During radio reception:
During radio reception:
Preset stations select 10
During CD/MD playback:
Disc change 13
5 DSPL (display mode change) button
8, 12, 13
6 MODE button
During radio reception:
BAND select 9, 10
During CD or MD playback:
CD/MD unit select 12
7 Z (eject) button 8
8 Display window
9 m/M(fast winding)/DIR (tape
transport direction change) buttons 8
0 D-BASS button 12
XR-C2200/XR-C2300X
D I SC
+
PR
S
T
+
-
D IS C
–
PR
ST
- -
MODE
DSPL
OFF
DIR
D-BASS
ENTER
MENU
SOUND
RELEASE
1
2
3
4
5
6
-SEEK/AMS
REP
SHUF
SOURCE
qa SOUND button 11
qs RELEASE (front panel release) button
6, 15
qd SEEK/AMS –/+ (cursor left/right) buttons
7, 9, 10, 11, 13
seek 10
Automatic Music Sensor 13
manual search 13
Automatic Music Sensor 13
manual search 13
qf Reset button (located on the front side
of the unit behind the front panel) 6
qg ENTER button 7, 9, 10, 11, 13
qh Number buttons
During radio reception
Preset number select 10
During CD/MD playback:
(1) REP 14
(2) SHUF 14
qj OFF button* 6
* Warning when installing in a car
without ACC (accessory) position on
the ignition key switch
Be sure to press (OFF) on the unit for two
seconds to turn off the clock display after
turning off the engine.
When you press (OFF) momentarily, the
clock display does not turn off and this
causes battery wear.
the ignition key switch
Be sure to press (OFF) on the unit for two
seconds to turn off the clock display after
turning off the engine.
When you press (OFF) momentarily, the
clock display does not turn off and this
causes battery wear.
Setting the clock
The clock uses a 12-hour digital indication.
Example: To set the clock to 10:08
1
Press (MENU), then press either side of
(PRST/DISC) repeatedly until “CLOCK”
appears.
(PRST/DISC) repeatedly until “CLOCK”
appears.
1
Press (ENTER).
The hour indication flashes.
2
Press either side of (PRST/DISC) to set
the hour.
the hour.
3
Press + side of (SEEK/AMS).
The minute indication flashes.
4
Press either side of (PRST/DISC) to set
the minute.
the minute.
2
Press (ENTER).
The clock starts.
After the clock setting is complete, the
display returns to normal playback mode.
display returns to normal playback mode.
4
182 m
m
53 m
m
Installation
Precautions
•Choose the installation location carefully so that the unit will not interfere with normal driving.
•Avoid installing the unit in areas subject to dust, dirt, excessive vibration, or high temperatures, such as
•Avoid installing the unit in areas subject to dust, dirt, excessive vibration, or high temperatures, such as
in direct sunlight or near heater ducts.
•Use only the supplied mounting hardware for a safe and secure installation.
Mounting angle adjustment
Adjust the mounting angle to less than 20
°
.
Note
To prevent malfunction, install only with the supplied screws 5.
To prevent malfunction, install only with the supplied screws 5.
A
B
Mounting example
Installation in the dashboard
1
2
3
Bend these claws outward for a
tight fit, if necessary.
tight fit, if necessary.
Plier ces griffes pour assurer
une prise correcte si nécessaire.
une prise correcte si nécessaire.
1
Mounting the unit in a Japanese car
You may not be able to install this unit in some makes of Japanese cars. In such a case, consult your Sony
dealer.
dealer.
How to detach and attach the front panel
Before installing the unit, detach the front panel.
A
To detach
Before detaching the front panel, be sure to press (OFF). Press (RELEASE), then slide the front panel a
little to the left, and pull it off towards you.
little to the left, and pull it off towards you.
B
To attach
Attach part
of the front panel to part
of the unit as illustrated and push the left side into position
until it clicks.
Installation
Précautions
•Choisir soigneusement l’emplacement d’installation pour que l’appareil ne gêne pas le chauffeur
pendant la conduite.
•Eviter d’installer l’appareil dans un endroit exposé à des températures élevées, comme en plein soleil ou
à proximité d’une bouche d’air chaud, ou à de la poussière, saleté ou vibrations violentes.
•Pour garantir un montage sûr, n’utiliser que le matériel fourni.
Réglage de l’angle de montage
Ajuster l’inclinaison à un angle inférieur à 20
°
.
Remarque
Pour éviter tout dysfonctionnement, utilisez uniquement les vis 5 pour le montage.
Pour éviter tout dysfonctionnement, utilisez uniquement les vis 5 pour le montage.
Exemple de montage
Installation dans le tableau de bord
Installation de l’appareil dans une voiture japonaise
Cet appareil ne peut pas être installé dans certaines voitures japonaise. Consultez, dans ce cas, votre
concessionnaire Sony.
concessionnaire Sony.
Retrait et pose de la façade
Avant d’installer l’appareil, déposer la façade.
A
Pour retirer
Avant de déposer la façade, ne pas oublier d’appuyer sur (OFF). Appuyer ensuite sur (RELEASE), puis
faire glisser la façade légèrement vers la gauche et enlever la façade en tirant à soi.
faire glisser la façade légèrement vers la gauche et enlever la façade en tirant à soi.
B
Pour attacher
Fixez la partie
de la façade sur la partie
de l’appareil, comme indiqué sur l’illustration, puis poussez
jusqu’au déclic.
(RELEASE)
2
3
Fire wall
Paroi ignifuge
Paroi ignifuge
Dashboard
Tableau de bord
Tableau de bord
1
4
First attach 6 to the unit, then insert
the unit into 1.
the unit into 1.
Fixez d’abord 6 sur l’appareil et
introduisez ensuite l’appareil dans 1.
introduisez ensuite l’appareil dans 1.
6
5
max. size
5
5
×
8 mm
Dimension
max. 5
max. 5
×
8 mm
5
max. size
5
5
×
8 mm
Dimension
max. 5
max. 5
×
8 mm
Bracket
Support
Support
to dashboard/center console
au tableau de bord/console centrale
au tableau de bord/console centrale
Existing parts supplied with your car
Pièces existantes fournies avec la voiture
Pièces existantes fournies avec la voiture
5
max. size
5
5
×
8 mm
Dimension
max. 5
max. 5
×
8 mm
to dashboard/center console
au tableau de bord/console centrale
au tableau de bord/console centrale
5
max. size
5
5
×
8 mm
Dimension
max. 5
max. 5
×
8 mm
Bracket
Support
Support
Existing parts supplied with your car
Pièces existantes fournies avec la voiture
Pièces existantes fournies avec la voiture
Bracket
Support
Support
Bracket
Support
Support
TOYOTA
NISSAN
(OFF)
With the UP marking up
Avec l’inscription UP vers le haut
Avec l’inscription UP vers le haut