DOWNLOAD Sony XR-1750 / XR-P200 / XR-T200 Service Manual ↓ Size: 3.05 MB | Pages: 34 in PDF or view online for FREE

– 13 –

1

Fit shaft of the lever (Pinch) ass’y
in hole on the chassis (M) ass’y and
install the lever (pinch) ass’y.

2

two polyethylene washers

3

Install the spring
(pinch press) to shaft 

A

.

Set the ends of spring to

B

 and 

C

.

shaft

shaft

B

C

C

B

shaft 

A

2

Install the hanger on to
two claws of the housing.

1

Install the catch to the hanger.

7

Holder the hanger by bending the claw.

A

part

B

part

C

part

D

part

8

Holder the hanger by
bending the claw.

3

Put the housing
under 

A

 part.

4

Fit claw on 

B

 part.

6

Fit projections on 

D

 part.

5

Fit projections on 

C

 part.

hanger

– 14 –

2

Move the arm (suction) in the arrow
direction and fit on projection.

1

Fit the arm (suction) on the shaft.

projection

1

Fit the lever (LDG-A)
on shaft 

A

 – 

C

 and install it.

shaft 

A

shaft 

B

shaft 

C

3

two type-E stop ring 2.0

2

Fit the lever (LDG-B)
on shafts 

A

 and 

B

 and

install.

shaft 

A

shaft 

B

– 15 –

2

guide (C)

1

three claws

4

Align hole in the gear (LDG-D) with

¢

 mark on the lever (LDG-A).

gear (LDG-FB)

hole

gear (LDG-D)

gear (LDG-A)

3

Move the lever (LDG-B)
in the arrow direction.

1

gear (LDG-A)

2

tension spring (lever LDG)

5

gear (LDG-FT)

6

polyethylene washer

– 16 –

1. Clean the following parts with a denatured-alcohol-moistened

swab:

playback head

pinch roller

rubber belt

capstan

idler

2. Demagnetize the playback head with a head demagnetizer.
3. Do not use a magnetized screwdriver for the adjustments.
4. The adjustments should be performed with the power supply

voltage (14.4 V) unless otherwise noted.

•

See the adjustment location from on page 17 for the
adjustment.

–1.5 to +2.5%

2,955 to 3,075 Hz

Specification: Constant speed

Adjustment Location: See page 17.

test tape
WS-48A
(3 kHz, 0 dB)

10 k 

Ω

LINE OUT

Procedure:
1. Put the set into the FWD PB mode.

Procedure:
1. Put the set into the FWD PB mode.

SOURCE button

: FM

FREQUENCY SELECT switch : 9 k (E, Australian model)

antenna jack  (J1)

0.01 µF

TU1 pin 

!•

Carrier frequency : 97.9 MHz (US model)

: 98.0 MHz (E, Australian model)

Output level

: 30 dB (31.6 µV)

Mode

: mono

Modulation

: 1 kHz, 75 kHz deviation

Procedure:
1. Tune the 97.9 MHz (US model) or 98.0 MHz (E, Australian

model).

2. Adjust RV1 on TU1 so that the digital voltmeter reading is

3.1 V.

Adjustment Location: See page 17.

Forward

CQ-403A

more than 60 g

Reverse

CQ-403R

(more than 2.12 oz)

•

Forward

CQ-102C

35–65 g•cm

(0.49–0.90 oz•inch)

Forward

CQ-102C

0.5–5.0 g•cm

Back Tension

(0.01–0.07 oz•inch)

Reverse

CQ-102RC

35–65 g•cm

(0.49–0.90 oz•inch)

Reverse

CQ-102RC

0.5–5.0 g•cm

Back Tension

(0.01–0.07 oz•inch)

FF, REW

CQ-201B

60–200 g•cm

(0.83–2.78 oz•inch)