DOWNLOAD Sony XAV-7W (serv.man2) Service Manual ↓ Size: 6.16 MB | Pages: 78 in PDF or view online for FREE

13

2

six screws (BTP2.6 

×

 6)

3

flat 40P cable (CN201)

5

monitor

1

Pull the monitor.

4

ground sheet (A) (CN202)

0

monitor (R) cabinet assy

1

three screws (2 

×

 6)

2

three screws (2 

×

 6)

6

flexible board (CN401)

7

connector (CN205)

3

two claws

9

monitor (F) cabinet assy

4

two claws

5

flat cable 10P (CN202)

8

connector (CN601)

14

2

LCD

1

two claws

1

two claws

3

three PCB retainers

3

two PCB retainers

1

connector (CN301)

5

monitor board

4

sheet (EMC)

2

three screws (2 

×

 6)

2

two screws (2 

×

 6)

15

 Follow the assembly procedure in the numerical order given.

250

150

flexible retainer

3

It lets flat cables pass
in two holes of flexible retainer.

2

flat cable 16P

1

flat cable 40P
Note: Turn the point-of-contact side up, bend to 

a valley type in a 250 mm portion, 
and make a crease.

Note: Turn the point-of-contact side up, bend to 

a valley type in a 150 mm portion, 
and make a crease.

sheet (tape)

4

Two cables are turned up 
in a fold portion and 
stuck with a sheet (tape).

5

Pass the ground sheet (A) as 
shown in a figure.

6

Bent a flexible retainer 
as shown in a figure.

8

two screws 
(M2 

×

 2.3)

7

flexible retainer

9

sheet (tape)

16

Adjusting Procedure:
1. Connect a digital voltmeter to the TP58 on the MONITOR

board.

2. Adjust the RV501 so that the reading of digital voltmeter is

7.50 

± 0.04 V.

Adjusting Procedure:
1. Connect a digital voltmeter to the TP64 on the MONITOR

board.

2. Adjust the RV602 so that the reading of digital voltmeter is

6.80 

± 0.04 V.

γ

Adjusting Procedure:
1. Connect a digital voltmeter to the TP67 on the MONITOR

board.

2. Adjust the RV213 so that the reading of digital voltmeter is

2.50 

± 0.04 V.

Use the following measuring equipment for the electrical
adjustment.
• Set (XAV-7W)
• Connection box (XA-114)
• PAL pattern generator
• Oscilloscope
• Frequency counter
• Digital voltmeter
• Regulated power supply

1. Open the monitor, and press the 

[MENU]

 button on the wireless

remote commander (RM-X118), and select the “MONITOR
TUNE” with the

M

 DISC +

or

m

 DISC –

button. Then, select

the “COLOR”, “HUE” with the

M

 DISC +

or

m

 DISC –

button,

and set the COLOR and HUE to the standard setting by pressing
the 

[ENTER]

 button for more than 2 seconds respectively.

2. For the monitor adjustment, use the 5-step gray scale signal

(chroma off) obtained from the pattern generator. Enter the
gray scale signal to the connection box (XA-114) and connect
an oscilloscope to the TP154 on the MONITOR board. Check
that the voltage between black and white of the gray scale signal
is 0.74Vp-p.

Adjusting Procedure:
1. Connect a frequency counter to the TP88 on the MONITOR

board.

2. Adjust the RV900 so that the reading of frequency counter is

145 

± 1 kHz.

Adjusting Procedure:
1. Connect a digital voltmeter to the TP57 on the MONITOR

board.

2. Adjust the RV503 so that the reading of digital voltmeter is

5.00 

± 0.04 V.

white

 black

0.74Vp-p

+
–

TP152 (GND)

TP88

set

(XAV-7W)

frequency

counter

digital

voltmeter

TP152 (GND)

TP57

set

(XAV-7W)

+
–

degital

voltmeter

TP152 (GND)

TP58

set

(XAV-7W)

+
–

+
–

degital

voltmeter

TP152 (GND)

TP64

set

(XAV-7W)

+
–

degital

voltmeter

PAL pattern

generator

TP152 (GND)

TP67

set

(XAV-7W)

connection box

(XA-114)

INPUT1

VIDEO jack