Sony WX-C5000 Service Manual ▷ View online
1
CD player section
Signal-to-noise ratio
94 dB
Frequency response
5 – 20,000 Hz
Wow and flutter
Below measurable limit
Cassette player section
Tape track
4-track 2-channel stereo
Wow and flutter
0.08 % (WRMS)
Frequency response
30 – 20,000 Hz
Signal-to-noise ratio
Cassette type
Dolby B NR
Dolby NR off
TYPE II, IV
67 dB
58 dB
TYPE I
64 dB
55 dB
Model Name Using Similar Mechanism
WX-C55
CD Drive Mechanism Type
MG-378X-121
Optical Pick-up Name
KSS-521A
Model Name Using Similar Mechanism
WX-C55
Tape Transport Mechanism Type
MG-25E-136
SERVICE MANUAL
E Model
WX-C5000
CHANGER CONTROL AUDIO MASTER
SPECIFICATIONS
– Continued on next page –
CD
Section
Section
TC
Section
Section
Dolby noise reduction manufactured under license from Dolby Labo-
ratories Licensing Corporation.
“DOLBY” and the double-D symbol
ratories Licensing Corporation.
“DOLBY” and the double-D symbol
;
are trademarks of Dolby
Laboratories Licensing Corporation.
Tuner section
FM
Tuning range
FM tuning interval:
50 kHz/200 kHz switchable
87.5 – 108.0 MHz
(at 50 kHz step)
87.5 – 107.9 MHz
(at 200 kHz step)
50 kHz/200 kHz switchable
87.5 – 108.0 MHz
(at 50 kHz step)
87.5 – 107.9 MHz
(at 200 kHz step)
Aerial terminal
External aerial connector
Intermediate frequency 10.7 MHz
Usable sensitivity
Usable sensitivity
9 dBf
Selectivity
75 dB at 400 kHz
Signal-to-noise ratio
65 dB (stereo),
68 dB (mono)
68 dB (mono)
Harmonic distortion at 1 kHz
0.7% (stereo),
0.4% (mono)
0.4% (mono)
Separation
35 dB at 1 kHz
Frequency response
30 – 15,000 Hz
2
SERVICE NOTE
CAUTION
Use of controls or adjustments or performance of proce-
dures other than those specified herein may result in haz-
ardous radiation exposure.
dures other than those specified herein may result in haz-
ardous radiation exposure.
Notes on Chip Component Replacement
•
Never reuse a disconnected chip component.
•
Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
aged by heat.
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
OR BASE UNIT
OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
breakdown because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also use
the procedure in the printed matter which is included in the repair
parts.
The flexible board is easily damaged and should be handled with
care.
breakdown because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also use
the procedure in the printed matter which is included in the repair
parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission, ob-
serve from more than 30 cm away from the objective lens.
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission, ob-
serve from more than 30 cm away from the objective lens.
NOTES ON PICK-UP FLEXIBLE BOARD
The pick-up flexible board in this set is secured to the optical pick-
up with an adhesive tape. Once the tape is removed, an adhering
force becomes weak, and it cannot be reused.
Therefore, if the optical pick-up is replaced, replace also the pick-
up flexible board with a new one.
up with an adhesive tape. Once the tape is removed, an adhering
force becomes weak, and it cannot be reused.
Therefore, if the optical pick-up is replaced, replace also the pick-
up flexible board with a new one.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
0
OR DOTTED LINE
WITH MARK
0
ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
AM
Tuning range
AM tuning interval:
9 kHz/10 kHz switchable
531 - 1,602 kHz
(at 9 kHz step)
530 – 1,710 kHz
(at 10 kHz step)
9 kHz/10 kHz switchable
531 - 1,602 kHz
(at 9 kHz step)
530 – 1,710 kHz
(at 10 kHz step)
Aerial terminal
External aerial connector
Intermediate frequency 10.71 MHz/450 kHz
Sensitivity
Sensitivity
30 µV
Power amplifier section
Outputs
Speaker outputs
(sure seal connectors)
(sure seal connectors)
Speaker impedance
4 – 8 ohms
Maximum power output 45 W
×
4 (at 4 ohms)
General
Outputs
Audio outputs (2)
Power aerial relay
control lead
Power amplifier control
lead
Power aerial relay
control lead
Power amplifier control
lead
Intputs
Telephone ATT control
lead
Illumination control lead
Bus audio input connector
Bus control input
lead
Illumination control lead
Bus audio input connector
Bus control input
Power requirements
12 V DC car battery
(negative ground)
(negative ground)
Dimensions
Approx. 178
×
100
×
181 mm
(w/h/d)
Mounting dimension
Approx. 178
×
100
×
160 mm
(w/h/d)
Mass
Approx. 2.2 kg
Supplied accessories
Parts for installation and
connections (1 set)
Dummy cover (1)
connections (1 set)
Dummy cover (1)
Design and specifications are subject to change without
notice.
notice.
3
TABLE OF CONTENTS
1. GENERAL
Location of Controls ............................................................... 4
Getting Started ........................................................................ 4
CD Player ............................................................................... 4
Cassette Player ....................................................................... 5
Radio ...................................................................................... 5
Other Functions ...................................................................... 5
CD/MD Unit ........................................................................... 6
Additional Information ........................................................... 7
Connections ............................................................................ 8
Getting Started ........................................................................ 4
CD Player ............................................................................... 4
Cassette Player ....................................................................... 5
Radio ...................................................................................... 5
Other Functions ...................................................................... 5
CD/MD Unit ........................................................................... 6
Additional Information ........................................................... 7
Connections ............................................................................ 8
2. DISASSEMBLY
2-1. Cover ................................................................................ 10
2-2. Front Panel Assy .............................................................. 10
2-3. CD Mechanism Block ...................................................... 11
2-4. TR Board, Heat Sink ........................................................ 11
2-5. CD Board ......................................................................... 12
2-6. Chassis (U) ....................................................................... 12
2-7. Tape Mechanism Block .................................................... 13
2-8. Main Board ...................................................................... 13
2-9. Chassis (TM) Assy ........................................................... 14
2-10. Sensor Board .................................................................... 14
2-11. Servo Board ...................................................................... 15
2-12. Roller Assy ....................................................................... 15
2-13. Chassis (OP) (O/S) Assy .................................................. 16
2-14. Optical Pick-up Block ...................................................... 16
2-2. Front Panel Assy .............................................................. 10
2-3. CD Mechanism Block ...................................................... 11
2-4. TR Board, Heat Sink ........................................................ 11
2-5. CD Board ......................................................................... 12
2-6. Chassis (U) ....................................................................... 12
2-7. Tape Mechanism Block .................................................... 13
2-8. Main Board ...................................................................... 13
2-9. Chassis (TM) Assy ........................................................... 14
2-10. Sensor Board .................................................................... 14
2-11. Servo Board ...................................................................... 15
2-12. Roller Assy ....................................................................... 15
2-13. Chassis (OP) (O/S) Assy .................................................. 16
2-14. Optical Pick-up Block ...................................................... 16
3. ASSEMBLY OF MECHANISM DECK
3-1. Housing ............................................................................ 17
3-2. Arm (Suction) ................................................................... 17
3-3. Lever (LDG-A)/(LDG-B) ................................................ 18
3-4. Gear (Loading FT) ........................................................... 18
3-5. Guide (C) .......................................................................... 19
3-6. Capstan/Reel Motor (M904) ............................................ 19
3-2. Arm (Suction) ................................................................... 17
3-3. Lever (LDG-A)/(LDG-B) ................................................ 18
3-4. Gear (Loading FT) ........................................................... 18
3-5. Guide (C) .......................................................................... 19
3-6. Capstan/Reel Motor (M904) ............................................ 19
4. MECHANICAL ADJUSTMENTS
.............................. 20
5. ELECTRICAL ADJUSTMENTS
Tape Section ......................................................................... 21
Tuner Section ........................................................................ 21
CD Section ........................................................................... 24
Tuner Section ........................................................................ 21
CD Section ........................................................................... 24
6. DIAGRAMS
6-1. IC Pin Descriptions .......................................................... 25
6-2. Block Diagram –CD Section– .......................................... 29
6-3. Block Diagram –Tape Section– ....................................... 30
6-4. Block Diagram –Main Section– ....................................... 31
6-5. Circuit Boards Location ................................................... 32
6-6. Printed Wiring Boards –CD Mechanism Section– ........... 33
6-7. Schematic Diagram –CD Mechanism Section (1/2)– ...... 34
6-8. Schematic Diagram –CD Mechanism Section (2/2)– ...... 35
6-9. Printed Wiring Board –TR Section– ................................ 36
6-10. Schematic Diagram –TR Section– ................................... 36
6-11. Printed Wiring Board –CD Section– ................................ 36
6-12. Schematic Diagram –CD Section– ................................... 37
6-13. Printed Wiring Board –Main Section– ............................. 38
6-14. Schematic Diagram –Main Section (1/4)– ....................... 40
6-15. Schematic Diagram –Main Section (2/4)– ....................... 41
6-16. Schematic Diagram –Main Section (3/4)– ....................... 42
6-17. Schematic Diagram –Main Section (4/4)– ....................... 43
6-18. Printed Wiring Board –Control Section– ......................... 44
6-19. Schematic Diagram –Control Section– ............................ 46
6-20. Printed Wiring Board –Jog Section– ................................ 47
6-21. Schematic Diagram –Jog Section– ................................... 47
6-2. Block Diagram –CD Section– .......................................... 29
6-3. Block Diagram –Tape Section– ....................................... 30
6-4. Block Diagram –Main Section– ....................................... 31
6-5. Circuit Boards Location ................................................... 32
6-6. Printed Wiring Boards –CD Mechanism Section– ........... 33
6-7. Schematic Diagram –CD Mechanism Section (1/2)– ...... 34
6-8. Schematic Diagram –CD Mechanism Section (2/2)– ...... 35
6-9. Printed Wiring Board –TR Section– ................................ 36
6-10. Schematic Diagram –TR Section– ................................... 36
6-11. Printed Wiring Board –CD Section– ................................ 36
6-12. Schematic Diagram –CD Section– ................................... 37
6-13. Printed Wiring Board –Main Section– ............................. 38
6-14. Schematic Diagram –Main Section (1/4)– ....................... 40
6-15. Schematic Diagram –Main Section (2/4)– ....................... 41
6-16. Schematic Diagram –Main Section (3/4)– ....................... 42
6-17. Schematic Diagram –Main Section (4/4)– ....................... 43
6-18. Printed Wiring Board –Control Section– ......................... 44
6-19. Schematic Diagram –Control Section– ............................ 46
6-20. Printed Wiring Board –Jog Section– ................................ 47
6-21. Schematic Diagram –Jog Section– ................................... 47
7. EXPLODED VIEWS
7-1. Cover Section ................................................................... 53
7-2. Front Panel Section .......................................................... 54
7-3. Chassis Section ................................................................ 55
7-4. Tape Mechanism Section ................................................. 56
7-5. CD Mechanism Section (1) .............................................. 57
7-6. CD Mechanism Section (2) .............................................. 58
7-7. CD Mechanism Section (3) .............................................. 59
7-2. Front Panel Section .......................................................... 54
7-3. Chassis Section ................................................................ 55
7-4. Tape Mechanism Section ................................................. 56
7-5. CD Mechanism Section (1) .............................................. 57
7-6. CD Mechanism Section (2) .............................................. 58
7-7. CD Mechanism Section (3) .............................................. 59
8. ELECTRICAL PARTS LIST
...................................
60
4
SECTION 1
GENERAL
This section extracted from
instruction manual.
instruction manual.
