Sony WX-7700MDX Service Manual ▷ View online
6
WX-7700MDX
The buttons on the unit share the same
functions as those on the card remote
commander.
functions as those on the card remote
commander.
a
ANGLE button
b
Sound window
c
SOURCE button
d
MODE button
e
VOL (+/–) button
f
Operation window
g
Receptor for the card remote
commander
commander
h
OPEN/CLOSE button
i
ATT button
j
Reset button
k
Frequency select switch
(located on the
bottom of the unit)
See “Frequency select switch” in the
Installation/Connections manual.
See “Frequency select switch” in the
Installation/Connections manual.
l
DISC (–/+) buttons
m
AMS (
. m
/
M >
) buttons
AMS (. m/M >) buttons share
the same functions as SEEK (</,)
buttons on the card remote commander.
the same functions as SEEK (</,)
buttons on the card remote commander.
n
OFF (Stop/Power off) button
*
*
Warning when installing in a car without
an ACC (accessory) position on the
ignition switch
After turning off the ignition switch, be sure to
press
an ACC (accessory) position on the
ignition switch
After turning off the ignition switch, be sure to
press
(OFF)
on the unit for 2 seconds to turn
off the clock display.
Otherwise, the clock display does not turn off
and this causes battery drain.
and this causes battery drain.
Controls of the unit
VOL
ANGLE
MODE
SOURCE
DISC
AMS
ATT
OPEN/
CLOSE
OFF
WX-7700MDX
7
WX-7700MDX
Display windows
a
DSO
Lights up while you are setting the DSO
mode.
mode.
b
POS
Lights up while you are setting the POS
mode.
mode.
c
DISC number
Appears only when an optional CD/MD unit
is connected and a disc in the optional unit is
played.
is connected and a disc in the optional unit is
played.
d
Track number
Appears during CD/MD playback.
e
Various items for a setting or a source
f
Cursor directions
The selectable cursor direction appears as a
“v”.
By pressing a cursor button (M/,/m/<) in
the same direction as any “v” that appears,
you can select an item or proceed with the
operation.
“v”.
By pressing a cursor button (M/,/m/<) in
the same direction as any “v” that appears,
you can select an item or proceed with the
operation.
g
ENTER
Appears when it's necessary to press (ENTER)
after you select an item.
after you select an item.
Sound window
Operation window
VOL
ANGLE
MODE
SOURCE
DISC
AMS
AT T
OPEN/
CLOSE
OFF
VOL
ANGLE
MODE
SOURCE
DISC
AMS
AT T
OPEN/
CLOSE
OFF
1
2
Level meter
(volume)
(volume)
This manual illustrates the
operation window mainly.
operation window mainly.
8
WX-7700MDX
Cautions
• This unit is designed for negative earth 12 V
DC operation only.
• Do not get the wires under a screw, or caught
in moving parts (e.g. seat railing).
• Before making connections, turn the car
ignition off to avoid short circuits.
• Connect the
yellow
and
red
power input leads
only after all other leads have been connected.
•
Run all earth wires to a common earth
point.
point.
• Be sure to insulate any loose unconnected
wires with electrical tape for safety.
Notes on the power supply cord (yellow)
• When connecting this unit in combination with
other stereo components, the connected car
circuit’s rating must be higher than the sum of
each component’s fuse.
circuit’s rating must be higher than the sum of
each component’s fuse.
• When no car circuits are rated high enough,
connect the unit directly to the battery.
Parts Iist (
1
)
The numbers in the list are keyed to those in the
instructions.
instructions.
Connection example (
2
)
Notes (
2
-A)
• Be sure to connect the earth lead before
connecting the amplifier.
• If you connect an optional power amplifier and do
not use the built-in amplifier, the beep sound will
be deactivated.
be deactivated.
Tip (
2
-B-
)
For connecting two or more changers, the source
selector XA-C30 (optional) is necessary.
selector XA-C30 (optional) is necessary.
Connection diagram (
3
)
When inserting each connector, be sure to insert
securely, as vibration through driving may
cause a poor connection.
securely, as vibration through driving may
cause a poor connection.
1
To a metal surface of the car
Make sure to connect the black earth lead first of
all, then proceed with connection steps
Make sure to connect the black earth lead first of
all, then proceed with connection steps
2
-
7
.
Check the black earth lead is connected properly,
before connecting the orange/white striped lead,
yellow and red power input leads.
before connecting the orange/white striped lead,
yellow and red power input leads.
2
To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting
any other system may damage the unit.
amplifier
This connection is only for amplifiers. Connecting
any other system may damage the unit.
2
B
Source selector
*
XA-C30
BUS CONTROL IN
A
3
To the power aerial control lead or power supply
lead of aerial booster amplifier
Notes
• I t is not necessary to connect this lead if there
Notes
• I t is not necessary to connect this lead if there
is no power aerial or aerial booster, or with a
manually-operated telescopic aerial.
manually-operated telescopic aerial.
• When your car has a built-in FM/AM aerial in
the rear/side glass, see “Notes on the control
and power supply leads.”
and power supply leads.”
4
To the interface cable of a car telephone
5
To a car’s illumination signal
Be sure to connect the black earth lead to it first.
Be sure to connect the black earth lead to it first.
6
To the +12 V power terminal which is energized
in the accessory position of the ignition key
switch
Notes
• If there is no accessory position, connect to the
in the accessory position of the ignition key
switch
Notes
• If there is no accessory position, connect to the
+12 V power (battery) terminal which is
energized at all times.
Be sure to connect the black earth lead to it
first.
energized at all times.
Be sure to connect the black earth lead to it
first.
• When your car has a built-in FM/AM aerial in
the rear/side glass, see “Notes on the control
and power supply leads.”
and power supply leads.”
7
To the +12 V power terminal which is energized
at all times
Be sure to connect the black earth lead to it first.
at all times
Be sure to connect the black earth lead to it first.
Notes on the control and power supply leads
• The power aerial control lead (blue) supplies +12 V
• The power aerial control lead (blue) supplies +12 V
DC when you turn on the tuner.
• When your car has built-in FM/AM aerial in the
rear/side glass, connect the power aerial control
lead (blue) or the accessory power input lead (red)
to the power terminal of the existing aerial
booster. For details, consult your dealer.
lead (blue) or the accessory power input lead (red)
to the power terminal of the existing aerial
booster. For details, consult your dealer.
• A power aerial without relay box cannot be used
with this unit.
Memory hold connection
When the yellow power input lead is connected,
power will always be supplied to the memory circuit
even when the ignition key is turned off.
When the yellow power input lead is connected,
power will always be supplied to the memory circuit
even when the ignition key is turned off.
Notes on speaker connection
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms,
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms,
and with adequate power handling capacities to
avoid its damage.
avoid its damage.
• Do not connect the speaker terminals to the car
chassis, or connect the terminals of the right
speakers with those of the left speaker.
speakers with those of the left speaker.
• Do not connect the earth lead of this unit to the
negative (–) terminal of the speaker.
• D o not attempt to connect the speakers in parallel.
• Connect only passive speakers. Connecting active
• Connect only passive speakers. Connecting active
speakers (with built-in amplifiers) to the speaker
terminals may damage the unit.
terminals may damage the unit.
• To avoid a malfunction, do not use the built-in
speaker wires installed in your car if the unit shares
a common negative (–) lead for the right and left
speakers.
a common negative (–) lead for the right and left
speakers.
• Do not connect the unit’s speaker cords to each
other.
SUBWOOFER OUT
(MONO)
*
not supplied
BUS AUDIO IN
BUS CONTROL IN
BUS AUDIO IN
AUDIO OUT
(FRONT)
AUDIO OUT
(REAR)
9
WX-7700MDX
L
R
L
R
REAR
AUX IN
FRONT
BUS AUDIO
AUDIO OUT
IN
3
1
4
5
6
Blue
Red
Yellow
4
Black
Max. supply current 0.1 A
Fuse (10 A)
BUS AUDIO IN
AMP REM
ANT REM
BUS CONTROL IN
Light blue
Max. supply current 0.3 A
White
Grey
Green
Purple
White/black striped
Grey/black striped
Green/black striped
Purple/black striped
Source selector
XA-C30
Left
Right
Left
Right
3
Blue/white striped
2
ATT
Supplied with the CD/MD changer
Supplied with XA-C30
SUBWOOFER OUT
(MONO)
RCA pin cord
*
1
Orange/white striped
7
ILLUMINATION
*
1
not supplied
*
2
Connect the Bus cable to its
terminal with the unit’s
V
mark and
the Bus cable’s
v
mark aligned.
*
3
supplied with the auxiliary
equipment
*
4
Auxiliary optional equipment such
as portable DVD player (not
supplied)
supplied)
*
2
from car aerial
AUX IN
AUDIO OUT
(REAR)
AUDIO OUT
(FRONT)
RCA pin cord
*
1
*
3
*
4
Notes
• Use the screws
1
or
2
depending on the make of
car. When this unit is attached to a MITSUBISHI car,
use the supplied screws
use the supplied screws
2
.
• T o prevent malfunction, be sure to install using
brackets and the supplied screws
1
or
2
.
• Do not apply excessive force to the buttons of the
unit.
• Do not push on the display window.
• Before mounting, make sure there is nothing on
• Before mounting, make sure there is nothing on
the top of the unit.
Warning when installing in a car
without ACC (accessory)
position on the ignition key
switch
without ACC (accessory)
position on the ignition key
switch
Be sure to press
(OFF)
on the unit for two
seconds to turn off the clock display after
turning off the engine.
turning off the engine.
When you press (OFF) only momentarily, the
clock display does not turn off and this causes
battery wear.
clock display does not turn off and this causes
battery wear.
Reset button
When the installation and connections are
completed, be sure to press the reset button with
a ballpoint pen, etc.
completed, be sure to press the reset button with
a ballpoint pen, etc.
Note
When you connect the power supply cord to the
unit or reset the unit, wait for about 10 seconds
before you insert a disc. If you insert a disc within
these 10 seconds, the unit will not be reset, and you
will have to press the reset button again.
unit or reset the unit, wait for about 10 seconds
before you insert a disc. If you insert a disc within
these 10 seconds, the unit will not be reset, and you
will have to press the reset button again.
Precautions
• Choose the installation location carefully so
that the unit will not interfere with normal
driving operations.
driving operations.
• Avoid installing the unit in areas subject to
dust, dirt, excessive vibration, or high
temperatures, such as in direct sunlight or near
heater ducts.
temperatures, such as in direct sunlight or near
heater ducts.
• Use only the supplied mounting hardware for
a safe and secure installation.
To open/close the front panel smoothly, to insert/
eject a disc easily, and especially to drive safely, a
certain distance between the front panel and the
shift lever is necessary. The necessary distance
differs, depending on the shift lever position of
your car. Before installing the unit, choose the
installation location carefully so that you can
drive safely.
To open/close the front panel smoothly, to insert/
eject a disc easily, and especially to drive safely, a
certain distance between the front panel and the
shift lever is necessary. The necessary distance
differs, depending on the shift lever position of
your car. Before installing the unit, choose the
installation location carefully so that you can
drive safely.
Mounting angle adjustment
Adjust the mounting angle to less than 30
°
.
Frequency select switch
The AM (FM) tuning interval is factory-set to the
9 k (50 k) position. If the frequency allocation
system of your country is based on 10 kHz (200
kHz) interval, set the switch
9 k (50 k) position. If the frequency allocation
system of your country is based on 10 kHz (200
kHz) interval, set the switch
on the bottom of
the unit
to the 10 k (200 k) position before
making connections.
After the frequency select switch is set, you must
press the reset button to reset the unit.
After the frequency select switch is set, you must
press the reset button to reset the unit.
Mounting the unit in a Japanese
car (
car (
4
)
You may not be able to install this unit in some
makes of Japanese cars. In such a case, consult
your Sony dealer.
makes of Japanese cars. In such a case, consult
your Sony dealer.
When mounting this unit to the preinstalled
brackets of your car, use the supplied screws 1
or 2 in the appropriate screw holes, according
to your vehicle: T for TOYOTA, M for
MITSUBISHI, and N for NISSAN.
brackets of your car, use the supplied screws 1
or 2 in the appropriate screw holes, according
to your vehicle: T for TOYOTA, M for
MITSUBISHI, and N for NISSAN.
4
A
TOYOTA/MITSUBISHI
to dashboard/centre console
Bracket
Bracket
1
or
2
max. size 5
×
8 mm
Existing parts supplied with your car
1
or
2
max. size 5
×
8 mm
VOL
ANGLE
MODE
SOURCE
DISC
AMS
ATT
OPEN/
CLOSE
OFF
Reset button
T
N
T
M
N
M
T
N
M
N
N
T
T
This illustration is for TOYOTA cars.
B
NISSAN
1
or
2
max. size 5
×
8 mm
Bracket
Existing parts supplied with your car
1
or
2
max. size 5
×
8 mm
to dashboard/centre console
3
WX-7700MDX
WX-7700MDX
Shift lever
88 mm
Bracket
Click on the first or last page to see other WX-7700MDX service manuals if exist.