DOWNLOAD Sony WX-4500X Service Manual ↓ Size: 6.46 MB | Pages: 61 in PDF or view online for FREE

17

2

 Move the arm (suction) in the arrow

Direction and fit on projection.

1

 Fit the arm (suction) on the shaft.

projection

Note : Follow the assembly procedure in the numerical order given.

7

 Holder the hanger by bending the claw.

1

Install the catcher to the hanger.

2

 Install the hanger onto

two claws of the housing.

3

 Put the housing

under 

A

 part.

6

 Fit projection on 

D

 part.

4

 Fit claw on 

B

 part.

5

 Fit projection on 

C

 part.

8

 Hold the hanger by

bending the claw.

hanger

housing

D

 part

head

C

 part

B

 part

A

 part

Head, Housing

Arm (Suction)

Guide (U)

Main Motor Assy

Lever (LDG-A) / (LDG-B)

Gear (Loading FT)

Note : This set can be assemble according to the following sequence.

18

1

 Fit the lever (LDG-A) on

shafts 

A

 to 

C

 and install it.

2

 Fit the lever (LDG-B) on

shafts 

A

 and 

B

 and install it.

3

 type-E stop ring 2.0

shaft 

A

shaft 

C

shaft 

A

shaft 

B

shaft 

B

5

 Align hole in the gear (LDG-D)

with hole the lever (LDG-A).

4

 Move the lever (LDG-B)

in the arrow direction.

2

 tension spring (LD-2)

1

3

 tension spring (LD-1)

7

 polyethylene washer

6

 gear (loading FT)

gear (LDG-D)

gear (LDG-FB)

lever (LDG-A)

hole

hole

19

1

 claws

2

 guide (C)

3

 belt (25)

2

 precision screws P 2x2

1

 main motor assy

(CAPSTAN/REEL) (M904)

30

°

20

set

frequency counter

test tape
WS-48A
(3 kHz, 0 dB)

SP OUT

4

Ω

1. Wipe the following components with an absorbent cotton cloth

moistened with alcohol before adjustment :

PB head

Pinch roller

Idler

Rubber belt

Capstan

2. Demagnetize the PB head using a head demagnetizer.
3. Be careful not to use a magnetized screwdriver.
4. After the adjustment is completed, lock the adjustment parts

using screws.

5. Unless otherwise specified, make adjustments at the specified

voltage (14.4 V).

2.95 – 6.37 mN • m

FWD

(30 – 65 g • cm)

CQ-102C

(0.42 – 0.90 oz • inch)

FWD

0.05 – 0.44 mN • m

Back Tension

(0.5 – 4.5 g • cm)

(0.01 – 0.06 oz • inch)

2.95 – 6.37 mN • m

REV

(30 – 65 g • cm)

CQ-102RC

(0.42 – 0.90 oz • inch)

REV

0.05 – 0.44 mN • m

(0.5 – 4.5 g • cm)

Back Tension

(0.01 – 0.06 oz • inch)

5.88 – 19.61 mN • m

FF, REW

CQ-201B

(60 – 200 g • cm)

(0.83 – 2.78 oz • inch)

FWD

CQ-403A

more than 90 g

REV

CQ-403R

(more than 3.17 oz)

Mode : FWD play

Tape Speed Adjustment

-Tape Mechanism Block upper side-

•

Adjustments of the tuner and CD sections have auto adjustments
in this set.

WS-48A

3 kHz, 0 dB

Tape speed adjustment

P-4-D400

400 Hz, 0 dB

Dolby level adjustment

Procedure:
1. Playback the test tape in the FWD play mode.
2. Verify that the reading on the digital frequency counter is in the

range between 3,010 and 3,300 Hz at the top of tape.

3. If the specified value is not met, adjust the variable resistor on

the capstan motor so that the reading is 3,000 Hz at the FWD
top of tape.