DOWNLOAD Sony MEX-DV1700U / MEX-DV1707U Service Manual ↓ Size: 2.96 MB | Pages: 55 in PDF or view online for FREE

Model
MEX-DV1700U MEX-DV1707U
Pages
55
Size
2.96 MB
Type
PDF
Document
Service Manual
Brand
Device
Car Audio
File
mex-dv1700u-mex-dv1707u.pdf
Date
PREV: Sony MEX-V50DT Service Manual

Sony MEX-DV1700U / MEX-DV1707U Service Manual ▷ View online

MEX-DV1700U/DV1707U
9
SECTION  3
DISASSEMBLY
Note: Follow the disassembly procedure in the numerical order given.
3-2.   SUB  PANEL  COMPLETE  ASSY
SET
3-2.  SUB PANEL COMPLETE ASSY
 (Page 
9)
3-3.  DVD MECHANISM DECK (MG-613XI-187)
 (Page 
10)
3-6. SERVO 
BOARD
 (Page 
11)
3-4.  DC FAN (25X25) (M801), MAIN BOARD
 (Page 
10)
3-5.  DVD MECHANISM DECK BLOCK
 (Page 
11)
3-7.  CHASSIS (T612Z) SUB ASSY,
 SENSOR 
BOARD
 (Page 
12)
FRONT PANEL SECTION
Note:
 Illustration of disassembly is omitted.
3-8.  CHASSIS (OP, ZA) COMPLETE ASSY
 (Page 
12)
1 screw
 (PTT2.6 
u 6)
5 two screws
 (PTT2.6 
u 6)
2 two bosses
2 two bosses
4 cover
6 two claws
3 three claws
6 two claws
7 sub panel complete assy
•  This set can be disassembled in the order shown below.
3-1.  DISASSEMBLY  FLOW
MEX-DV1700U/DV1707U
10
3-3.   DVD  MECHANISM  DECK (MG-613XI-187)
3-4.   DC  FAN (25X25)  (M801),  MAIN  BOARD
1 screw
 (PTT
2.6
 
u 6)
7 DVD mechanism deck
 (MG-613XI-187)
4 connector 
 (CN
40
1)
5 cover (FFC)
2 Lift up the DVD 
 mechanism 
deck 
 (MG-613XI-187)
1 screw
 (PTT
2.6
 
u 6)
6 filament tape
3 flexible flat cable (60 core) 
 (CN101)
qf MAIN board
5 fuse (blade type) (auto fuse)
 
(10 A/32 V) (FU801)
4 chassis
3 insulating sheet
0 two screws
 
(PS2.6 
u 14)
8 screw
 
(PTT2.6 
u 8)
1 two screws
 
(PTT2.6 
u 8)
9 connection cord (front audio out,
 
rear/sub audio out, AUX audio in)
qd DC fan (25 u 25)
 
(M801)
qs sheet (GPS wire)
qa connector
 
(CN802)
7 connector
 
(CN803)
2  three ground point screws
 (PTT2.6 
u 6)
6  Lift up the lead pin.
Note 2: When the DC fan and MAIN board are mounted, 
 
lock connection cord for auto mobile and wire DC fan
 
by push lead pin.
Note 1: When COMPLETE MAIN BOARD for MEX-DV1700U: E (PAL), Iranian and Nigerian models is replaced, the destination 
setting is necessary. Refer to “NOTE THE MAIN BOARD OR SYSTEM CONTROLLER (IC502) REPLACING” on page 4.
Note: Since form of the shield surrounding DVD mechanism deck (MG-613XI-187) 
has been changed in the midway of production, it may differ from this illustration.
Ver. 1.2
MEX-DV1700U/DV1707U
11
3-5.  DVD  MECHANISM  DECK  BLOCK
3-6.  SERVO  BOARD
Note 1: Adhesive (ST-854GH) 10 
 33 m tape cannot re-used.
 
  Please replace to brand-new part ones adhesive (ST-854GH) 10 
 33 m tape is removed.
1 adhesive
 (ST-854GH)
 10 
u 33 m tape
1 adhesive (ST-854GH)
 10 
u 33 m tape
3 two screws
 
(PTT2.6 
u 5)
2 two screws
 
(P1.7 
u 2.2)
4 shield (613)
3 shield (613S)
5 bracket (DVD)
6 DVD mechanism deck block
2 screw
 
(PTT2.6 
u 5)
4 screw
 
(PTT2.6 
u 5)
1 two screws
 
(P1.7 
u 2.2)
5 bracket (DVD)
6 DVD mechanism deck block
Former type
New type
– DVD mechanism deck block (Bottom view) –
2 Remove the two solders 
 
of loading motor wire.
0 SERVO board
SERVO board
RED
WHITE
7 three screws
 
(M1.7 
u 2.5)
5 OP flexible board
 
(CN2)
4 cord with connector
9 flexible flat cable (60 core)
 
(CN10)
6 sled motor flexible board
 
(CN1)
8 
1 adhesive (ST-854GH)
 10 
u 33 m tape
1 adhesive (ST-854GH)
 10 
u 33 m tape
 Note 
2: When disconnecting the OP flexible board from
 
 
of the connector. Be sure to refer to “NOTE FOR
 
 
FLEXIBLE BOARD OF THE OPTICAL PICK-UP” 
 
 
of the servicing notes (See page 5).
3 Remove the five solders 
 
of SENSOR board wire
 
and cord with connector.
SERVO board
RED
RED
WHITE
WHITE
BLACK
Ver. 1.1
Note 1: The shield of DVD mechanism deck has been changed in the midway of production.
Note 2: Adhesive (ST-854GH) 10 
 33 m tape cannot re-used.
 
  Please replace to brand-new part ones adhesive (ST-
854GH) 10 
 33 m tape is removed.
MEX-DV1700U/DV1707U
12
3-7.  CHASSIS (T612Z)  SUB  ASSY,  SENSOR  BOARD
3-8.  CHASSIS (OP,  ZA)  COMPLETE  ASSY
1 two screws
 
(P1.7 
u 2.2)
4 chassis (T612Z) sub assy
1 two screws
 
(P1.7 
u 2.2)
2 claw
3 claw
5 Remove the three solders.
6 SENSOR borad
A
5
1 OP flexible board
 
(CN2)
6 two coil springs 
 (damper)
8 chassis (OP, ZA) complete assy
7 compression spring 
 (damper, 
Z)
2 flexible board
 
(CN1)
3 tension spring (KF)
tension spring (KF)
‡0HWKRGRILQVWDOOLQJWHQVLRQVSULQJ.)
4 Turn the gear (RA1) fully 
 
in the direction of arrow A.
Hang in order of 
A, B by pay
attention spring of direction.
A
B
±%RWWRPYLHZ±
Page of 55
Display

Click on the first or last page to see other MEX-DV1700U / MEX-DV1707U service manuals if exist.

RANDOM: