DOWNLOAD Sony MEX-D30 / MEX-V30 Service Manual ↓ Size: 1.23 MB | Pages: 12 in PDF or view online for FREE

Choose the installation location carefully so that the 
unit will not interfere with normal driving operations.
Avoid installing the unit in areas subject to dust, dirt, 
excessive vibration, or high temperature, such as in 
direct sunlight or near heater ducts.
Use only the supplied mounting hardware for a safe and 
secure installation.

Adjust the mounting angle to less than 30°.

Be sure to connect the parking brake lead (light green) of 
the power supply connection cable 

 to the parking 

brake switch cord. The mounting position of the parking 
brake switch cord depends on your car. Consult your car 
dealer or your nearest Sony dealer for further details.

Pinch both edges of the protection collar 

 and 

push outwards, then pull out.

  Insert both release keys 

 together between 

the unit and the bracket 

 until they click.

   Pull down the bracket 

, then pull up the unit 

to separate.

( -2).

( -3).

Before detaching the front panel, be sure to press 

. 

Press 

, then slide the front panel to the right side, 

and pull out the left side.

Engage part 

 of the front panel with part 

 of the unit, 

as illustrated, and push the left side into position until it 
clicks.

Unnecessary battery drainage will occur if the unit is 
wired directly to a car ignition system that does not have 
an ACC position. To avoid battery drainage, install a 
suitable switch on the ACC line.

When the installation and connections are completed, be 
sure to press the reset button with a ballpoint pen, etc.

The auxiliary power connector may vary depending on 
your car. Check your car’s auxiliary power connector 
diagram to make sure the connections match correctly. 
There are two basic types (illustrated below). You may 
need to switch the positions of the red and yellow leads of 
the unit’s power supply connection cable 

.

After matching the connections and switched power 
supply leads correctly, connect the unit to the car’s power 
supply. If you have any questions and problems 
connecting your unit that are not covered in these 
instructions, please consult your car dealer.

•  This set can be disassembled in the order shown below.

Note: Follow the disassembly procedure in the numerical order given.

 Note: Illustration of disassembly is omitted.

1 screw 

u 5) (MEX-V30)

2 boss

4 cover

2 boss

3 two claws

Note 1: Before disconnecting the FPC (SJ-V049-01) of optical pick-up block, solder the short-land.

Note 3: When assembling the optical pick-up block, 
 

remove the solder of short-land after 

 

connecting the FPC (SJ-V049-01).

2

1 screw 

u 5) (MEX-V30)

4 Lift up the lead pin.

5 FPC (SJ-V049-01)

6 FFC (deck to MAIN MT, SJ-V049-0)

7 DVD deck assy

1 three screws 

u 5) (MEX-V30)

2: When you install three screws, fix by the following bond.

Part No. 

Description

7-432-916-01  BOND TAFF, SONY 20 ml

3 Solder the short-land.

3 two screws 

u 3) (MEX-D30)

u 3) (MEX-V30)

5 FFC (S. panel to M. MT, SJ-V049-0)

6 sub panel complete assy

3 two screws

u 3) (MEX-D30)

u 3) (MEX-V30)

2 Remove 

1 fixing cloth

4

8 screw

u 8) (MEX-V30)

8 two screws

u 8) (MEX-V30)

9 three screws

u 5.2) (MEX-D30)

u 5) (MEX-V30)

1 fuse (blade type) (auto fuse) 

2 connector

4 connector

6 connector

3 cord (V/A out) with bracket 

5 cord (audio) with bracket 

7 cord (video in) with bracket 

0 MAIN board