Sony MEX-D30 / MEX-V30 Service Manual ▷ View online
MEX-D30/V30
5
Cautions
Run all ground (earth) leads to a common ground
(earth) point.
This unit is designed for negative ground (earth) 12 V
DC operation only.
Do not disassemble or modify the unit.
Do not install in locations which interfere with airbag
operation.
Do not get the leads under a screw, or caught in moving
parts (e.g. seat railing).
Before making connections, turn the car ignition off to
avoid short circuits.
Connect the yellow and red power supply leads only
after all other leads have been connected.
Be sure to insulate any loose unconnected leads with
electrical tape for safety.
Do not press on the LCD when installing the unit.
Install the unit with the monitor facing straight forward;
do not install it at a slanted angle.
(earth) point.
This unit is designed for negative ground (earth) 12 V
DC operation only.
Do not disassemble or modify the unit.
Do not install in locations which interfere with airbag
operation.
Do not get the leads under a screw, or caught in moving
parts (e.g. seat railing).
Before making connections, turn the car ignition off to
avoid short circuits.
Connect the yellow and red power supply leads only
after all other leads have been connected.
Be sure to insulate any loose unconnected leads with
electrical tape for safety.
Do not press on the LCD when installing the unit.
Install the unit with the monitor facing straight forward;
do not install it at a slanted angle.
Notes on the power supply lead (yellow)
When connecting this unit in combination with other
stereo components, the amperage rating of the car
circuit to which the unit is connected must be higher
than the sum of each component's fuse amperage rating.
If no car circuits are rated high enough, connect the unit
directly to the battery.
stereo components, the amperage rating of the car
circuit to which the unit is connected must be higher
than the sum of each component's fuse amperage rating.
If no car circuits are rated high enough, connect the unit
directly to the battery.
Connection example
Notes (
-A)
Be sure to connect the ground (earth) lead before connecting the amplifier.
The alarm will only sound if the built-in amplifier is used.
The alarm will only sound if the built-in amplifier is used.
Note (
-B)
You cannot use multiple auxiliary devices simultaneously, even if they are
connected to different terminals.
connected to different terminals.
Connection diagram
To AMP REMOTE IN of an optional power
amplifier
amplifier
This connection is only for amplifiers. Connecting any other system
may damage the unit.
may damage the unit.
To the car's reverse lamp cord for an optional rear
view camera
To the parking brake switch cord
To an auxiliary device such as a portable media
player, game console, etc. (not supplied)
view camera
To the parking brake switch cord
To an auxiliary device such as a portable media
player, game console, etc. (not supplied)
Tip
You can use an RCA cord (not supplied) to connect auxiliary devices.
You can use an RCA cord (not supplied) to connect auxiliary devices.
Warning
If you have a power antenna (aerial) without a relay box,
connecting this unit with the supplied power supply
connection cable
connecting this unit with the supplied power supply
connection cable
may damage the antenna (aerial).
Notes on the control and power supply leads
The power antenna (aerial) control lead (blue) supplies +12 V DC when
you turn on the tuner.
If your car has a built-in FM/AM antenna (aerial) in the rear/side glass,
connect the power antenna (aerial) control lead (blue) or the accessory
power supply lead (red) to the power terminal of the antenna (aerial)
booster. For details, consult your car dealer.
A power antenna (aerial) without a relay box cannot be used with this unit.
you turn on the tuner.
If your car has a built-in FM/AM antenna (aerial) in the rear/side glass,
connect the power antenna (aerial) control lead (blue) or the accessory
power supply lead (red) to the power terminal of the antenna (aerial)
booster. For details, consult your car dealer.
A power antenna (aerial) without a relay box cannot be used with this unit.
Memory hold connection
When the yellow power supply lead is connected, power will always be
supplied to the memory circuit even when the ignition switch is turned off.
When the yellow power supply lead is connected, power will always be
supplied to the memory circuit even when the ignition switch is turned off.
Notes on speaker connection
Before connecting the speakers, turn the unit off.
Use speakers with an impedance of 4 to 8 ohms, and with adequate
power handling capacities to avoid damage.
Do not connect the speaker terminals to the car chassis, or connect the
terminals of the right speakers with those of the left speakers.
Do not connect the ground (earth) lead of this unit to the negative (–)
terminal of a speaker.
Do not attempt to connect the speakers in parallel.
Connect only passive speakers. Connecting active speakers (with
built-in amplifiers) to the speaker terminals may damage the unit.
To avoid a malfunction, do not use the built-in speaker leads installed in
your car if they feature a common negative (–) lead for the right and left
speakers.
Do not connect the unit’s speaker leads to each other.
Use speakers with an impedance of 4 to 8 ohms, and with adequate
power handling capacities to avoid damage.
Do not connect the speaker terminals to the car chassis, or connect the
terminals of the right speakers with those of the left speakers.
Do not connect the ground (earth) lead of this unit to the negative (–)
terminal of a speaker.
Do not attempt to connect the speakers in parallel.
Connect only passive speakers. Connecting active speakers (with
built-in amplifiers) to the speaker terminals may damage the unit.
To avoid a malfunction, do not use the built-in speaker leads installed in
your car if they feature a common negative (–) lead for the right and left
speakers.
Do not connect the unit’s speaker leads to each other.
REAR/SUB
AUDIO OUT
FRONT
AUDIO OUT
REAR
VIDEO OUT
A
B
CAMERA IN
AUX
AUDIO IN
AUX
VIDEO IN
*not supplied
Video camera*
REAR VIDEO OUT
AUX VIDEO IN
AUX AUDIO IN
CAMERA IN
REAR/SUB
AUDIO OUT
FRONT
AUDIO OUT
*
1
For details on connecting to the parking brake switch cord, see
“Connecting the parking brake lead
( )” on the reverse side.
*
2
RCA pin cord (not supplied)
Blue/white striped
AMP REM
Max. supply current: 0.3 A
PARKING BRAKE
REVERSE IN
From car antenna (aerial)
Fuse (10 A)
For details, see “Power connection diagram” on the reverse side.
Light green
Purple/white striped
Positions 1, 2, and 3 do not have pins.
4
Yellow
Continuous power supply
5
Blue
Power antenna (aerial) control
6
Orange
Switched illumination power supply
7
Red
Switched power supply
8
Black
Ground (earth)
Negative polarity positions 2, 4, 6, and 8 have striped leads.
1
Purple
+
Speaker, rear, right
2
–
Speaker, rear, right
3
Gray
+
Speaker, front, right
4
–
Speaker, front, right
5
White
+
Speaker, front, left
6
–
Speaker, front, left
7
Green
+
Speaker, rear, left
8
–
Speaker, rear, left
*
2
*
2
*
2
*
2
*
1
*
2
From the car’s speaker connector
From the car’s power connector
MEX-V30:
MEX-D30/V30
6
Precautions
Choose the installation location carefully so that the
unit will not interfere with normal driving operations.
Avoid installing the unit in areas subject to dust, dirt,
excessive vibration, or high temperature, such as in
direct sunlight or near heater ducts.
Use only the supplied mounting hardware for a safe and
secure installation.
unit will not interfere with normal driving operations.
Avoid installing the unit in areas subject to dust, dirt,
excessive vibration, or high temperature, such as in
direct sunlight or near heater ducts.
Use only the supplied mounting hardware for a safe and
secure installation.
Mounting angle adjustment
Adjust the mounting angle to less than 30°.
Connecting the parking brake
lead
lead
Be sure to connect the parking brake lead (light green) of
the power supply connection cable
the power supply connection cable
to the parking
brake switch cord. The mounting position of the parking
brake switch cord depends on your car. Consult your car
dealer or your nearest Sony dealer for further details.
brake switch cord depends on your car. Consult your car
dealer or your nearest Sony dealer for further details.
Removing the protection
collar and the bracket
collar and the bracket
Before installing the unit, remove the protection
collar
collar
and the bracket
from the unit.
1
Remove the pre-installed screws.
2
Remove the protection collar
.
Pinch both edges of the protection collar
and
push outwards, then pull out.
3
Remove the bracket
.
Insert both release keys
together between
the unit and the bracket
until they click.
Pull down the bracket
, then pull up the unit
to separate.
Mounting example
Installation in the dashboard
Notes
Bend these claws outward for a tight fit, if necessary
( -2).
Make sure that the 2 catches on the protection collar
are properly
engaged in the slots of the unit
( -3).
How to detach and attach the
front panel
front panel
Before installing the unit, detach the front panel.
-A To detach
Before detaching the front panel, be sure to press
.
Press
, then slide the front panel to the right side,
and pull out the left side.
-B To attach
Engage part
of the front panel with part
of the unit,
as illustrated, and push the left side into position until it
clicks.
clicks.
Warning if your car’s ignition
has no ACC position
has no ACC position
Unnecessary battery drainage will occur if the unit is
wired directly to a car ignition system that does not have
an ACC position. To avoid battery drainage, install a
suitable switch on the ACC line.
wired directly to a car ignition system that does not have
an ACC position. To avoid battery drainage, install a
suitable switch on the ACC line.
Reset button
When the installation and connections are completed, be
sure to press the reset button with a ballpoint pen, etc.
sure to press the reset button with a ballpoint pen, etc.
Foot brake type
Parking brake switch cord
Hand brake type
Parking brake switch cord
1
3
Dashboard
Fire wall
Claws
2
A
B
Red
Red
Yellow
Yellow
Red
Red
Yellow
Yellow
Power connection diagram
The auxiliary power connector may vary depending on
your car. Check your car’s auxiliary power connector
diagram to make sure the connections match correctly.
There are two basic types (illustrated below). You may
need to switch the positions of the red and yellow leads of
the unit’s power supply connection cable
your car. Check your car’s auxiliary power connector
diagram to make sure the connections match correctly.
There are two basic types (illustrated below). You may
need to switch the positions of the red and yellow leads of
the unit’s power supply connection cable
.
After matching the connections and switched power
supply leads correctly, connect the unit to the car’s power
supply. If you have any questions and problems
connecting your unit that are not covered in these
instructions, please consult your car dealer.
supply leads correctly, connect the unit to the car’s power
supply. If you have any questions and problems
connecting your unit that are not covered in these
instructions, please consult your car dealer.
Auxiliary power connector
4
Yellow
Continuous power supply
7
Red
Switched power supply
4
Yellow
Switched power supply
7
Red
Continuous power supply
Face the hook inwards.
1
2
3
MEX-D30/V30
7
SECTION 3
DISASSEMBLY
• This set can be disassembled in the order shown below.
3-1. DISASSEMBLY FLOW
Note: Follow the disassembly procedure in the numerical order given.
3-2. COVER
3-2. COVER
(Page
(Page
7)
3-3. DVD
DECK
ASSY
(DL-C28DB2-YG2-SP:
MEX-D30/
DL-C28DB2-YG2:
MEX-V30)
(Page
8)
3-4. SUB PANEL COMPLETE ASSY
(Page
(Page
9)
3-5. MAIN
BOARD
(Page
9)
SET
FRONT PANEL SECTION
Note: Illustration of disassembly is omitted.
1 screw
(BTT M3) (MEX-D30)
(M3
u 5) (MEX-V30)
2 boss
4 cover
2 boss
3 two claws
Ver. 1.2
MEX-D30/V30
8
3-3. DVD DECK ASSY (DL-C28DB2-YG2-SP: MEX-D30/DL-C28DB2-YG2: MEX-V30)
Note 1: Before disconnecting the FPC (SJ-V049-01) of optical pick-up block, solder the short-land.
Note 3: When assembling the optical pick-up block,
remove the solder of short-land after
connecting the FPC (SJ-V049-01).
2
1 screw
(BTT M3) (MEX-D30)
(M3
u 5) (MEX-V30)
4 Lift up the lead pin.
5 FPC (SJ-V049-01)
(CON2)
6 FFC (deck to MAIN MT, SJ-V049-0)
(J101)
7 DVD deck assy
(DL-C28DB2-YG2-SP)
(MEX-D30)
(DL-C28DB2-YG2)
(MEX-V30)
1 three screws
(BTT M3) (MEX-D30)
(M3
u 5) (MEX-V30)
Note
2: When you install three screws, fix by the following bond.
Part No.
Description
7-432-916-01 BOND TAFF, SONY 20 ml
3 Solder the short-land.
)OH[LEOHSULQWHGFDEOHVHWWLQJ
rear side
MAIN board
lead pin
Ver. 1.2
Click on the first or last page to see other MEX-D30 / MEX-V30 service manuals if exist.