Sony MEX-BT3600U Service Manual ▷ View online
MEX-BT3600U
9
E, Mexican and Indian models:
Location of controls and basic operations
Main unit
This section contains instructions on the location
of controls and basic operations. For details, see
the respective pages.
The corresponding buttons on the card remote
The corresponding buttons on the card remote
commander control the same functions as those
on the unit.
" OFF button
To power off; stop the source.
#
(BROWSE) button
To enter the Quick-BrowZer mode.
$ Control dial/select/
(handsfree)
button
To adjust volume/select search category
To adjust volume/select search category
(rotate); select setup items (press and rotate);
receive/end a call (press).
% SOURCE button
To power on; change the source (Radio/CD/
USB/AUX/Bluetooth audio/Bluetooth
phone).
& Disc slot
Insert the disc (label side up), playback
starts.
' Display window
( USB terminal
To connect to the USB device.
) ;(eject) button
To eject the disc.
*
(front panel release) button
+
(BACK) button
To return to the previous display.
, Receptor for the card remote
commander
- SEEK –/+ buttons
CD/USB:
To skip tracks (press); skip tracks
continuously (press, then press again within
about 1 second and hold); reverse/fast-
forward a track (press and hold).
BT
BTM
DSPL
L
R
C
S
F
U
H
S
P
E
R
1
2
3
4
5
6
PAUSE
BROWSE
BACK
SEEK
SEEK
MODE
SOURCE
PUSH SELECT /
MIC
AUX
OFF
ALBUM
BLUETOOTH
RB
RE
R
RT
RGRH
RL
RK
RM
RI
RESET
XB
X
Radio:
To tune in stations automatically (press); find
a station manually (press and hold).
Bluetooth audio device*
1
:
To skip tracks (press).
. MODE button
To select the radio band (FM/MW/SW);
select the play mode of ATRAC Audio
Device.
/ BLUETOOTH button
For Bluetooth signal on/off, pairing.
0 BTM button
To start the BTM function (press and hold).
1 Frequency select switch (located on the
bottom of the unit)
See “Frequency select switch” in the
See “Frequency select switch” in the
supplied installation/connections manual.
2 Number buttons
CD/USB:
/ : ALBUM –/+ (during MP3/WMA/
/ : ALBUM –/+ (during MP3/WMA/
AAC playback)
To skip albums (press); skip albums
continuously (press and hold).
: REP
: SHUF
: PAUSE*
: SHUF
: PAUSE*
2
To pause playback. To cancel, press
again.
Radio:
To receive stored stations (press); store
stations (press and hold).
Bluetooth audio device*
1
:
: PAUSE*
2
To pause playback. To cancel, press
again.
Bluetooth phone:
: MIC
: MIC
3 DSPL (display)/SCRL (scroll) button
To change display items (press); scroll the
display item (press and hold).
4 AUX input jack
To connect a portable audio device.
5 RESET button (located behind the front
panel)
6 Microphone
Note
Do not cover the microphone, the handsfree
function may not work properly.
Do not cover the microphone, the handsfree
function may not work properly.
*1 When a Bluetooth audio device (supports
AVRCP of Bluetooth technology) is connected.
Depending on the device, certain operations
may not be available.
Depending on the device, certain operations
may not be available.
*2 When playing back on this unit.
Notes
• When ejecting/inserting a disc, keep any USB
• When ejecting/inserting a disc, keep any USB
devices disconnected to avoid damage to the disc.
• If the unit is turned off and the display disappears,
it cannot be operated with the card remote
commander unless 4063$& on the unit is
commander unless 4063$& on the unit is
pressed, or a disc is inserted to activate the unit
first.
first.
About USB cap
When not using the USB terminal ((), use the
When not using the USB terminal ((), use the
supplied USB cap to prevent dust or dirt entering.
Keep the USB cap out of the reach of children to
prevent accidental swallowing.
Keep the USB cap out of the reach of children to
prevent accidental swallowing.
Card remote commander
RM-X304
RM-X304
The following buttons on the card remote
commander have also different buttons/functions
from the unit. Remove the insulation film before
use.
" OFF button
To power off; stop the source.
# SOURCE button
To power on; change the source (Radio/CD/
USB/AUX/Bluetooth audio/Bluetooth
phone).
$ ()/
() buttons
To control CD/radio/USB/Bluetooth audio,
the same as 4&&,
–/+ on the unit.
Setup, sound setting, etc., can be operated by
.
.
% DSPL (display) button
To change display items.
& VOL (volume) +/– button
To adjust volume.
' ATT (attenuate) button
To attenuate the sound. To cancel, press
again.
( MODE button
To select the radio band (FM/MW/SW);
select the play mode of ATRAC Audio
Device.
) SEL (select)/
(handsfree) button
The same as the select button on the unit.
During the Quick-BrowZer mode, 4&-
(select) is inactive.
* . (+)/N (–) buttons
To control CD/USB, the same as
/
(ALBUM –/+) on the unit.
Setup, sound setting, etc., can be operated by
. N.
. N.
+ SCRL (scroll) button
To scroll the display item.
, Number buttons
To receive stored stations (press); store
stations (press and hold).
OFF
DSPL
SCRL
SEL
SOURCE
MODE
1
3
2
4
6
5
ATT
VOL
+
–
+
–
RB
MEX-BT3600U
10
Except AEP, Russian and UK models:
L
R
FRONT
AUDIO OUT
SUB REAR
SUB AUDIO OUT
REMOTE
IN
REAR
AUDIO OUT
FRONT
AUDIO OUT
Cautions
Be sure to install this unit in the dashboard of the car
as the rear side of the unit becomes hot during use.
• This unit is designed for negative ground (earth) 12 V
DC operation only.
• Do not get the leads under a screw, or caught in moving
parts (e.g. seat railing).
• Before making connections, turn the car ignition off to
avoid short circuits.
• Connect the yellow and red power input leads only
after all other leads have been connected.
• Run all ground (earth) leads to a common
ground (earth) point.
• Be sure to insulate any loose unconnected leads with
electrical tape for safety.
• Do not cover the ventilation slots or heat sinks of the
unit.
Notes on the power supply lead (yellow)
• When connecting this unit in combination with other
stereo components, the connected car circuit’s rating
must be higher than the sum of each component’s fuse.
• When no car circuits are rated high enough, connect
the unit directly to the battery.
Parts Iist
• The numbers in the list are keyed to those in the
instructions.
• The bracket
and the protection collar are
attached to the unit before shipping. Before mounting
the unit, use the release keys
to remove the bracket
and the protection collar from the unit. For
details, see “Removing the protection collar and the
bracket (
)” on the reverse side of the sheet.
• Keep the release keys
for future use as they
are also necessary if you remove the unit from
your car.
Caution
Handle the bracket
carefully to avoid injuring your
fingers.
Catch
Note
Before installing, make sure that the catches on both sides of
the bracket
are bent inwards 2 mm. If the catches are straight
or bent outwards, the unit will not be installed securely and may
spring out.
Connection example
Notes
• Be sure to connect the ground (earth) lead before connecting
the amplifier.
• The alarm will only sound if the built-in amplifier is used.
Connection diagram
To a metal surface of the car
First connect the black ground (earth) lead, then connect the
yellow and red power supply leads.
To the power antenna (aerial) control lead or
power supply lead of antenna (aerial) booster
amplifier
Notes
• It is not necessary to connect this lead if there is no power
antenna (aerial) or antenna (aerial) booster, or with a
manually-operated telescopic antenna (aerial).
• When your car has a built-in FM/MW/SW antenna (aerial)
in the rear/side glass, see “Notes on the control and power
supply leads.”
To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting any other
system may damage the unit.
To the interface cable of a car telephone
To the +12 V power terminal which is
energized in the accessory position of the
ignition key switch
Notes
• If there is no accessory position, connect to the +12 V
power (battery) terminal which is energized at all times.
Be sure to connect the black ground (earth) lead to a
metal surface of the car first.
• When your car has a built-in FM/MW/SW antenna (aerial)
in the rear/side glass, see “Notes on the control and power
supply leads.”
To the +12 V power terminal which is
energized at all times
Be sure to connect the black ground (earth) lead to a metal
surface of the car first.
Notes on the control and power supply leads
• The power antenna (aerial) control lead (blue) supplies +12 V
DC when you turn on the tuner.
• When your car has built-in FM/MW/SW antenna (aerial) in the
rear/side glass, connect the power antenna (aerial) control
lead (blue) or the accessory power input lead (red) to the
power terminal of the existing antenna (aerial) booster. For
details, consult your dealer.
• A power antenna (aerial) without a relay box cannot be used
with this unit.
Memory hold connection
When the yellow power input lead is connected, power will
always be supplied to the memory circuit even when the ignition
switch is turned off.
Notes on speaker connection
Notes on speaker connection
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms, and with
adequate power handling capacities to avoid its damage.
• Do not connect the speaker terminals to the car chassis, or
connect the terminals of the right speakers with those of the
left speaker.
• Do not connect the ground (earth) lead of this unit to the
negative (–) terminal of the speaker.
• Do not attempt to connect the speakers in parallel.
• Connect only passive speakers. Connecting active speakers
(with built-in amplifiers) to the speaker terminals may damage
the unit.
• To avoid a malfunction, do not use the built-in speaker leads
installed in your car if the unit shares a common negative (–)
lead for the right and left speakers.
• Do not connect the unit’s speaker leads to each other.
Note on connection
Note on connection
If speaker and amplifier are not connected correctly, “FAILURE”
appears in the display. In this case, make sure the speaker and
amplifier are connected correctly.
Precauciones
Asegúrese de instalar la unidad en el tablero del
automóvil, ya que la parte posterior de la unidad se
calienta durante el uso.
• Esta unidad ha sido diseñada para alimentarse sólo con cc
de 12 V de masa negativa.
• No coloque los cables debajo de ningún tornillo, ni los
aprisione con partes móviles (p. ej. los raíles del asiento).
• Antes de realizar las conexiones, desactive el encendido
del automóvil para evitar cortocircuitos.
• Conecte los cables de entrada de alimentación amarillo y
rojo solamente después de haber conectado los demás.
• Conecte todos los cables de conexión a masa a
un punto común.
• Por razones de seguridad, asegúrese de aislar con cinta
aislante los cables sueltos que no estén conectados.
• No cubra las ranuras ni las rejillas de ventilación de la
unidad.
Notas sobre el cable de fuente de alimentación
(amarillo)
• Cuando conecte esta unidad en combinación con otros
componentes estéreo, la capacidad nominal del circuito
conectado del automóvil debe ser superior a la suma del
fusible de cada componente.
• Si no hay circuitos del automóvil con capacidad nominal
suficientemente alta, conecte la unidad directamente a la
batería.
Lista de componentes
• Los números de la lista corresponden a los de las
instrucciones.
• La unidad se comercializa con el soporte
y el marco
de protección
ya colocados. Antes de montarla,
utilice las llaves de liberación
para extraer el
soporte
y el marco de protección de la misma.
Para obtener más información, consulte “Extracción
del marco de protección y del soporte (
)”.
• Conserve las llaves de liberación
para
utilizarlas en el futuro, ya que también las
necesitará si retira la unidad del automóvil.
Precaución
Tenga mucho cuidado al manipular el soporte
para
evitar posibles lesiones en los dedos.
Enganche
Nota
Antes de instalar la unidad, compruebe que los enganches de
ambos lados del soporte
están doblados hacia adentro 2 mm.
Si no lo están o están doblados hacia afuera, la unidad no se
instalará correctamente y puede saltar.
Ejemplo de conexiones
Notas
• Asegúrese de conectar primero el cable de conexión a masa
antes de realizar la conexión del amplificador.
• La alarma sonará únicamente si se utiliza el amplificador
incorporado.
Diagrama de conexión
A una superficie metálica del automóvil
Conecte primero el cable de conexión a masa negro, y después
los cables amarillo, y rojo de entrada de alimentación.
Al cable de control de la antena motorizada
o al cable de fuente de alimentación del
amplificador de señal de la antena
Notas
• Si no se dispone de antena motorizada ni de amplificador
de antena, o se utiliza una antena telescópica accionada
manualmente, no será necesario conectar este cable.
• Si el automóvil dispone de una antena de FM/MW/SW
incorporada en el cristal trasero o lateral, consulte “Notas
sobre los cables de control y de fuente de alimentación”.
A AMP REMOTE IN de un amplificador de
potencia opcional
Esta conexión es sólo para amplificadores. La conexión de
cualquier otro sistema puede dañar la unidad.
Al cable de interfaz de un teléfono para
automóvil
Al terminal de alimentación de +12 V que
recibe energía en la posición de accesorio del
interruptor de la llave de encendido
Notas
• Si no hay posición de accesorio, conéctelo al terminal de
alimentación (batería) de +12 V que recibe energía sin
interrupción.
Asegúrese de conectar primero el cable de conexión a masa
negro a una superficie metálica del automóvil.
• Si el automóvil dispone de una antena de FM/MW/SW
incorporada en el cristal trasero o lateral, consulte “Notas
sobre los cables de control y de fuente de alimentación”.
Al terminal de alimentación de +12 V que recibe
energía sin interrupción
Asegúrese de conectar primero el cable de conexión a masa
negro a una superficie metálica del automóvil.
Notas sobre los cables de control y de fuente de alimentación
• El cable de control de la antena motorizada (azul) suministrará cc
de + 12 V cuando conecte la alimentación del sintonizador.
• Si el automóvil dispone de una antena de FM/MW/SW incorporada
en el cristal trasero o lateral, conecte el cable de control de antena
motorizada (azul) o el cable de entrada de alimentación auxiliar
(rojo) al terminal de alimentación del amplificador de antena
existente. Para obtener más información, consulte a su distribuidor.
• Con esta unidad no es posible utilizar una antena motorizada sin
caja de relé.
Conexión para protección de la memoria
Si conecta el cable de entrada de alimentación amarillo, el circuito
de la memoria recibirá siempre alimentación, aunque apague el
interruptor de encendido.
Notas sobre la conexión de los altavoces
Notas sobre la conexión de los altavoces
• Antes de conectar los altavoces, desconecte la alimentación de la
unidad.
• Utilice altavoces con una impedancia de 4 a 8
Ω con la capacidad
de potencia adecuada para evitar que se dañen.
• No conecte los terminales de altavoz al chasis del automóvil, ni
conecte los terminales del altavoz derecho con los del izquierdo.
• No conecte el cable de conexión a masa de esta unidad al
terminal negativo (–) del altavoz.
• No intente conectar los altavoces en paralelo.
• Conecte solamente altavoces pasivos. Si conecta altavoces
activos (con amplificadores incorporados) a los terminales de
altavoz, puede dañar la unidad.
• Para evitar fallas de funcionamiento, no utilice los cables de altavoz
incorporados instalados en el automóvil si la unidad comparte un
cable negativo común (–) para los altavoces derecho e izquierdo.
• No conecte los cables de altavoz de la unidad entre sí.
Nota sobre la conexión
Nota sobre la conexión
Si el altavoz y el amplificador no están conectados correctamente,
aparecerá “FAILURE” en la pantalla. En tal caso compruebe la
conexión de ambos dispositivos.
from car antenna (aerial)
desde la antena del automóvil
desde la antena del automóvil
REAR
AUDIO OUT
SUB AUDIO OUT
FRONT AUDIO OUT
AMP REM
Max. supply current 0.3 A
Corriente máx. de alimentación de 0,3 A
Corriente máx. de alimentación de 0,3 A
Fuse (10 A)
Fusible (10 A)
Fusible (10 A)
Blue/white striped
Con rayas azules y blancas
Con rayas azules y blancas
Red
Rojo
Rojo
Yellow
Amarillo
Amarillo
White
Blanco
Blanco
Green
Verde
Verde
Purple
Morado
Morado
White/black striped
Con rayas blancas y negras
Con rayas blancas y negras
Grey/black striped
Con rayas grises y negras
Con rayas grises y negras
Green/black striped
Con rayas verdes y negras
Con rayas verdes y negras
Grey
Gris
Gris
Left
Izquierdo
Izquierdo
Right
Derecho
Derecho
Left
Izquierdo
Izquierdo
Right
Derecho
Derecho
ANT REM
Black
Negro
Negro
Blue
Azul
Azul
Max. supply current 0.1 A
Corriente máx. de alimentación de 0,1 A
Purple/black striped
Con rayas moradas y negras
Con rayas moradas y negras
*
1
*
1
ATT
Light blue
Azul celeste
Azul celeste
*
2
*
1
RCA pin cord (not supplied)
*
2
Insert with the cord upwards.
*
1
Cable con terminales RCA
(no suministrado)
*
2
Insertar con el cable hacia arriba.
*
1
MEX-BT3600U
11
1
2
3
182 m
m
53 m
m
Dashboard
Tablero
Tablero
A
TOYOTA
to dashboard/centre console
al tablero o consola central
al tablero o consola central
Bracket
Soporte
Soporte
Bracket
Soporte
Soporte
B
NISSAN
to dashboard/centre console
al tablero o consola central
al tablero o consola central
Bracket
Soporte
Soporte
Bracket
Soporte
Soporte
Existing parts supplied with your car
Piezas existentes suministradas con su automóvil
Piezas existentes suministradas con su automóvil
A
B
max. size
5
5
× 8 mm
Tamaño máx.
5
5
× 8 mm
max. size
5
5
× 8 mm
Tamaño máx.
5
5
× 8 mm
max. size
5
5
× 8 mm
Tamaño máx.
5
5
× 8 mm
max. size
5
5
× 8 mm
Tamaño máx.
5
5
× 8 mm
Face the hook inwards.
El gancho debe
encontrarse en la parte
interior.
El gancho debe
encontrarse en la parte
interior.
Claws
Uñas
Uñas
Mounting the unit in a Japanese
car
You may not be able to install this unit in some makes of
Japanese cars. In such a case, consult your Sony dealer.
Note
To prevent malfunction, install only with the supplied screws
.
How to detach and attach the
front panel
Before installing the unit, detach the front panel.
-A To detach
Before detaching the front panel, be sure to press
.
Press
, and pull it off towards you.
-B To attach
Engage part
of the front panel with part of the unit,
as illustrated, and push the left side into position until it
clicks.
Warning if your car’s ignition
has no ACC position
Be sure to set the Auto Off function. For details, see the
supplied Operating Instructions.
The unit will shut off completely and automatically in
the set time after the unit is turned off, which prevents
battery drain.
If you do not set the Auto Off function, press and hold
until the display disappears each time you turn
the ignition off.
RESET button
When the installation and connections are completed, be
sure to press the RESET button with a ballpoint pen, etc.,
after detaching the front panel.
Precautions
• Choose the installation location carefully so that the
unit will not interfere with normal driving operations.
• Avoid installing the unit in areas subject to dust, dirt,
excessive vibration, or high temperatures, such as in
direct sunlight or near heater ducts.
• Use only the supplied mounting hardware for a safe
and secure installation.
Mounting angle adjustment
Adjust the mounting angle to less than 45°.
Removing the protection collar
and the bracket
Before installing the unit, remove the protection
collar
and the bracket from the unit.
1
Remove the protection collar
.
Engage the release keys together with the
protection collar
.
Pull out the release keys to remove the
protection collar
.
2
Remove the bracket
.
Insert both release keys together between
the unit and the bracket
until they click.
Pull down the bracket , then pull up the unit
to separate.
Frequency select switch
The MW (FM) tuning interval is factory-set to the 9 k
(50 k) position. If the frequency allocation system of
your country is based on 10 kHz (200 kHz) interval, set
the switch on the bottom of the unit to the 10 k (200 k)
position before making connections.
Mounting example
Installation in the dashboard
Notes
• Bend these claws outward for a tight fit, if necessary (
-2).
• Make sure that the 4 catches on the protection collar
are
properly engaged in the slots of the unit (
-3).
Forma de extraer e instalar el
panel frontal
Antes de instalar la unidad, extraiga el panel
frontal.
-A Para extraerlo
Antes de extraer el panel frontal, asegúrese de presionar
. Después presione y tire de él hacia usted.
-B Para instalarlo
Coloque la parte
del panel frontal en la parte de
la unidad, como se muestra en la ilustración, y después
presione la parte izquierda hasta que encaje.
Advertencia: si el encendido del
automóvil no dispone de una
posición ACC
Asegúrese de ajustar la función de desconexión
automática. Para obtener más información, consulte el
manual de instrucciones suministrado.
La unidad se apagará completa y automáticamente en
el tiempo establecido después de que se desconecte la
unidad, lo que evita que se desgaste la batería.
Si no ha ajustado la función de desconexión automática,
mantenga presionado
cada vez que apague
el interruptor de encendido, hasta que la pantalla
desaparezca.
Botón RESET
Una vez finalizada la instalación y las conexiones,
desmonte el panel frontal y presione el botón RESET con
un bolígrafo o un objeto similar.
Precauciones
• Elija cuidadosamente el lugar de montaje de forma que
la unidad no interfiera con las funciones normales de
conducción.
• Evite instalar la unidad donde pueda quedar sometida
a polvo, suciedad, vibraciones excesivas o altas
temperaturas como, por ejemplo, a la luz solar directa o
cerca de conductos de calefacción.
• Para realizar una instalación segura y firme, utilice
solamente elementos de instalación suministrados.
Ajuste del ángulo de montaje
Ajuste el ángulo de montaje a menos de 45°.
Extracción del marco de
protección y del soporte
Antes de instalar la unidad, retire el marco de
protección
y el soporte de la misma.
1
Retire el marco de protección
.
Acople las llaves de liberación al marco de
protección
.
Retire las llaves de liberación para extraer
el marco de protección
.
2
Retire el soporte
.
Inserte ambas llaves de liberación entre la
unidad y el soporte
hasta que encajen.
Presione el soporte y, a continuación,
levante la unidad para separar ambos
elementos.
Selector de frecuencia
El intervalo de sintonía de MW (FM) ha sido ajustado
en fábrica en la posición 9 k (50 k). Si el sistema de
asignación de frecuencias de su país se basa en el
intervalo de 10 kHz (200 kHz), ajuste este selector,
situado en la base de la unidad, en la posición 10 k
(200 k) antes de realizar las conexiones.
Ejemplo de montaje
Instalación en el tablero
Notas
• Si es necesario, doble estos ganchos hacia fuera para que
encaje firmemente (
-2).
• Compruebe que los 4 enganches del marco de protección
estén bien fijados en las ranuras de la unidad (
-3).
Existing parts supplied with your car
Piezas existentes suministradas con su automóvil
Piezas existentes suministradas con su automóvil
1
2
Orient the release key
correctly.
Oriente la llave de
liberación en la
dirección correcta.
correctly.
Oriente la llave de
liberación en la
dirección correcta.
Fire wall
Cortafuegos
Cortafuegos
Montaje de la unidad en un
automóvil japonés
Es posible que no pueda instalar esta unidad en algunos
automóviles japoneses. En tal caso, consulte a su
distribuidor Sony.
Nota
Para evitar que se produzcan fallas de funcionamiento, realice la
instalación solamente con los tornillos suministrados
.
(E, Mexican and Indian models)
(E, Mexican and Indian models)
(E, Mexican and Indian models)
MEX-BT3600U
12
AEP, Russian and UK models:
L
R
FRONT
AUDIO OUT
SUB REAR
5 7
8
1 3
5 7
2 4
6 8
"
#
4
REMOTE
IN
FRONT
AUDIO OUT
SUB AUDIO OUT
REAR
AUDIO OUT
Let op
Installeer dit apparaat in het dashboard van de auto
omdat de achterkant van het apparaat tijdens gebruik
heet kan worden.
• Dit apparaat is ontworpen voor gebruik op een auto-accu
van 12 V gelijkstroom, negatief geaard.
• Zorg ervoor dat de kabels niet onder een schroef of tussen
bewegende onderdelen (b.v. zetelrail) terechtkomen.
• Voordat u de aansluitingen maakt, moet u het contact
uitzetten om kortsluiting te vermijden.
• Sluit het netsnoer
aan op het apparaat en
de luidsprekers voordat u het aansluit op de
hulpvoedingsaansluiting.
• Sluit alle aardingskabels op een
gemeenschappelijk aardpunt aan.
• Voorzie niet aangesloten kabels om veiligheidsredenen
altijd van isolatietape.
• Dek de ventilatieopeningen of koelplaten van het apparaat
niet af.
Opmerkingen bij de voedingskabel (geel)
• Wanneer u dit apparaat aansluit samen met andere
componenten, moet het vermogen van de aangesloten
autostroomkring groter zijn dan de som van de zekeringen
van elke component afzonderlijk.
• Wanneer het vermogen ontoereikend is, moet u het
apparaat rechtstreeks aansluiten op de accu.
Onderdelenlijst
• De nummers in de afbeelding verwijzen naar die in de
instructies.
• De beugel
en de beschermende rand worden
bevestigd op het apparaat voordat dit wordt
verzonden. Voordat u het apparaat plaatst, moet u de
ontgrendelingssleutels
gebruiken om de beugel en
de beschermende rand
te verwijderen van het apparaat.
Zie "De beschermende rand en de beugel verwijderen
(
)" op de achterkant van dit vel voor meer informatie.
• Bewaar de ontgrendelingssleutels
voor
toekomstig gebruik omdat u deze ook nodig hebt
om het apparaat uit de auto te verwijderen.
Let op
Houd de beugel
voorzichtig vast zodat u uw vingers niet
verwondt.
Greep
Opmerking
Voordat u het apparaat installeert, moet u de grepen aan beide
zijden van de beugel
2 mm naar binnen buigen. Als de grepen
recht zijn of naar buiten gebogen, kan het apparaat niet goed
worden bevestigd en kan dit losschieten.
Voorbeeldaansluitingen
Opmerkingen
• Sluit eerst de aardingskabel aan voordat u de versterker aansluit.
• U hoort de pieptoon alleen als de ingebouwde versterker wordt
gebruikt.
Aansluitschema
Naar AMP REMOTE IN van een optionele
eindversterker
Deze aansluiting is alleen bedoeld voor versterkers. Door
een ander systeem aan te sluiten kan het apparaat worden
beschadigd.
Naar het interfacesnoer van een autotelefoon
Waarschuwing
Indien u een elektrische antenne hebt zonder relaiskast, kan
het aansluiten van dit apparaat met het bijgeleverde netsnoer
de antenne beschadigen.
Opmerkingen over de bedienings- en voedingskabels
• De antennevoedingskabel (blauw) levert +12 V gelijkstroom
wanneer u de tuner inschakelt of de AF (Alternative Frequency) of
TA (Traffic Announcement) functie activeert.
• Wanneer uw auto is uitgerust met een FM/MW/LW-antenne in de
achterruit/zijruit, moet u de antennevoedingskabel (blauw) of de
hulpvoedingskabel (rood) aansluiten op de voedingsingang van
de bestaande antenneversterker. Raadpleeg uw dealer voor meer
details.
• Met dit apparaat is het niet mogelijk een automatische antenne
zonder relaiskast te gebruiken.
Instandhouden van het geheugen
Zolang de gele voedingskabel is aangesloten, blijft de
stroomvoorziening van het geheugen intact, ook wanneer het
contact van de auto wordt uitgeschakeld.
Opmerkingen betreffende het aansluiten van de luidsprekers
Opmerkingen betreffende het aansluiten van de luidsprekers
• Zorg dat het apparaat is uitgeschakeld, alvorens de luidsprekers
aan te sluiten.
• Gebruik luidsprekers met een impedantie van 4 tot 8 Ohm en let
op dat die het vermogen van de versterker kunnen verwerken. Als
u dit niet doet, kunnen de luidsprekers ernstig beschadigd raken.
• Verbind in geen geval de aansluitingen van de luidsprekers met
het chassis van de auto en sluit de aansluitingen van de rechter-
en linkerluidspreker niet op elkaar aan.
• Verbind de aardingskabel van dit apparaat niet met de negatieve
(–) aansluiting van de luidspreker.
• Probeer nooit de luidsprekers parallel aan te sluiten.
• Sluit geen actieve luidsprekers (met ingebouwde versterkers)
aan op de luidsprekeraansluiting van dit apparaat. Dit zal leiden
tot beschadiging van de actieve luidsprekers. Sluit dus altijd
uitsluitend luidsprekers zonder ingebouwde versterker aan.
• Om defecten te vermijden mag u de bestaande
luidsprekerbedrading in uw auto niet gebruiken wanneer er een
gemeenschappelijke negatieve (–) kabel is voor de rechter- en
linkerluidsprekers.
• Verbind de luidsprekerkabels niet met elkaar.
Opmerking over aansluiten
Opmerking over aansluiten
Als de luidspreker en versterker niet correct zijn aangesloten, wordt
"FAILURE" in het display weergegeven. In dit geval moet u zorgen
dat de luidspreker en versterker correct zijn aangesloten.
Précautions
Installez cet appareil sur le tableau de bord de la voiture,
car l’arrière de l’appareil chauffe en cours d’utilisation.
• Cet appareil est conçu pour fonctionner sur un courant
continu de 12 V avec masse négative.
• Evitez de coincer les câbles sous des vis ou dans des
pièces mobiles (par exemple, armature de siège).
• Avant d’effectuer des raccordements, coupez le moteur
pour éviter les courts-circuits.
• Branchez le câble d’alimention
sur l’appareil et les
haut-parleurs avant de le brancher sur le connecteur
d’alimentation auxiliaire.
• Rassemblez tous les câbles de terre en un point
de masse commun.
• Veillez à isoler tout câble ou câble non connecté avec du
ruban isolant.
• Ne recouvrez pas les orifices d’aération ou les dissipateurs
thermiques de l’appareil.
Remarques sur le câble d’alimentation (jaune)
• Lorsque cet appareil est raccordé à d’autres équipements
stéréo, la valeur nominale des circuits du véhicule
raccordés doit être supérieure à la somme des fusibles de
chaque élément.
• Si aucun circuit de la voiture n’est assez puissant,
raccordez directement l’appareil à la batterie.
Liste des composants
• Les numéros de la liste correspondent à ceux des
instructions.
• Le support
et le tour de protection sont fixés à
l’appareil en usine. Avant le montage de l’appareil,
utilisez les clés de déblocage
pour détacher le support
et le tour de protection de l’appareil. Pour de plus
amples informations, reportez-vous à la section « Retrait
du tour de protection et du support (
) » au verso de la
feuille.
• Conservez les clés de déblocage
pour une
utilisation ultérieure car vous en aurez également
besoin pour retirer l’appareil de votre véhicule.
Avertissement
Manipulez le support
avec soin pour éviter de vous
blesser aux doigts.
Loquet
Remarque
Avant l’installation, assurez-vous que les loquets des deux côtés du
support
sont bien pliés de 2 mm vers l’intérieur. Si les loquets
sont droits ou pliés vers l’extérieur, l’appareil ne peut pas être fixé
solidement et peut se détacher.
Exemple de raccordement
Remarques
• Raccordez d’abord le câble de mise à la masse avant de
connecter l’amplificateur.
• L’alarme est émise uniquement lorsque l’amplificateur intégré est
utilisé.
Schémas de raccordement
Vers AMP REMOTE IN d’un amplificateur de
puissance facultatif
Ce raccordement existe seulement pour les amplificateurs. Le
raccordement à tout autre système peut endommager l’appareil.
Vers le cordon de liaison d’un téléphone de
voiture
Avertissement
Si vous disposez d’une antenne électrique sans boîtier de
relais, le branchement de cet appareil au moyen du cordon
d’alimentation fourni
risque d’endommager l’antenne.
Remarques sur les câbles de commande et d’alimentation
• Le câble de commande (bleu) fournit du courant continu de +12 V
lorsque vous mettez le tuner sous tension ou lorsque vous activez
la fonction AF (fréquence alternative) ou TA (informations de
circulation).
• Lorsque votre voiture est équipée d’une antenne FM/MW
(GO)/LW (PO) intégrée dans la vitre arrière/latérale, raccordez le
câble de commande d’antenne (bleu) ou l’entrée d’alimentation
des accessoires (rouge) au bornier de l’amplificateur d’antenne
existant. Pour plus de détails, consultez votre revendeur.
• Une antenne électrique sans boîtier de relais ne peut pas être
utilisée avec cet appareil.
Raccordement pour la conservation de la mémoire
Lorsque le câble de commande d’antenne jaune est connecté, le
circuit de la mémoire est alimenté en permanence même si la clé de
contact est en position d’arrêt.
Remarques sur le raccordement des haut-parleurs
Remarques sur le raccordement des haut-parleurs
• Avant de raccorder les haut-parleurs, mettre l’appareil hors
tension.
• Utiliser des haut-parleurs ayant une impédance de 4 à 8 ohms et
une capacité adéquate sous peine de les endommager.
• Ne pas raccorder les bornes du système de haut-parleurs au
châssis de la voiture et ne pas connecter les bornes du haut-
parleur droit à celles du haut-parleur gauche.
• Ne pas raccorder le câble de mise à la masse de cet appareil à la
borne négative (–) du haut-parleur.
• Ne pas tenter de raccorder les haut-parleurs en parallèle.
• Connecter uniquement des haut-parleurs passifs. La connexion
de haut-parleurs actifs (avec des amplificateurs intégrés) aux
bornes des haut-parleurs pourrait endommager l’appareil.
• Pour éviter tout problème de fonctionnement, n’utilisez pas les
câbles des haut-parleurs intégrés installés dans votre voiture si
l’appareil dispose d’un câble négatif commun (–) pour les haut-
parleurs droit et gauche.
• Ne raccordez pas entre eux les cordons des haut-parleurs de
l’appareil.
Remarque sur le raccordement
Si les enceintes et l’amplificateur ne sont pas raccordés
correctement, le message « FAILURE » s’affiche. Dans ce cas,
assurez-vous que les enceintes et l’amplificateur sont raccordés
correctement.
Vorsichtsmaßnahmen
Installieren Sie das Gerät unbedingt im Armaturenbrett
des Fahrzeugs, denn die Rückseite des Geräts erwärmt
sich bei Betrieb.
• Dieses Gerät ist ausschließlich für den Betrieb bei 12 V
Gleichstrom (negative Erdung) bestimmt.
• Achten Sie darauf, dass die Kabel nicht unter einer
Schraube oder zwischen beweglichen Teilen wie z. B. in
einer Sitzschiene eingeklemmt werden.
• Schalten Sie, bevor Sie irgendwelche Anschlüsse
vornehmen, die Zündung des Fahrzeugs aus, um
Kurzschlüsse zu vermeiden.
• Verbinden Sie das Stromversorgungskabel
mit dem
Gerät und den Lautsprechern, bevor Sie es mit dem
Hilfsstromanschluss verbinden.
• Schließen Sie alle Massekabel an einen
gemeinsamen Massepunkt an.
• Aus Sicherheitsgründen müssen alle losen, nicht
angeschlossenen Drähte mit Isolierband abgeklebt werden.
• Decken Sie die Lüftungsschlitze und Kühlkörper des
Geräts nicht ab.
Hinweise zum Stromversorgungskabel (gelb)
• Wenn Sie dieses Gerät zusammen mit anderen
Stereokomponenten anschließen, muss der
Autostromkreis, an den die Geräte angeschlossen sind,
eine höhere Leistung aufweisen als die Summe der
Sicherungen der einzelnen Komponenten.
• Wenn kein Autostromkreis eine so hohe Leistung
aufweist, schließen Sie das Gerät direkt an die Batterie an.
Teileliste
• Die Nummern in der Liste sind dieselben wie im
Erläuterungstext.
• Die Halterung
und die Schutzumrandung werden
vor dem Ausliefern am Gerät angebracht. Bevor Sie
das Gerät montieren, nehmen Sie die Halterung
und
die Schutzumrandung
mithilfe der Löseschlüssel
bitte vom Gerät ab. Einzelheiten dazu finden Sie unter
„Abnehmen der Schutzumrandung und der Halterung
(
)“ auf der Rückseite dieses Blattes.
• Bewahren Sie die Löseschlüssel
für den
späteren Gebrauch auf. Sie werden
z. B. benötigt, wenn Sie das Gerät aus dem
Fahrzeug ausbauen wollen.
Vorsicht
Seien Sie beim Umgang mit der Halterung
vorsichtig,
damit Sie sich nicht die Hände verletzen.
Verriegelung
Hinweis
Vergewissern Sie sich vor dem Installieren, dass die Verriegelungen
an beiden Seiten der Halterung
um 2 mm nach innen gebogen
sind. Wenn die Verriegelungen gerade oder nach außen gebogen sind,
lässt sich das Gerät nicht sicher installieren und kann herausspringen.
Anschlussbeispiel
Hinweise
• Schließen Sie unbedingt zuerst das Massekabel an, bevor Sie
den Verstärker anschließen.
• Der Warnton wird nur ausgegeben, wenn der integrierte
Verstärker verwendet wird.
Anschlussdiagramm
An AMP REMOTE IN des gesondert erhältlichen
Endverstärkers
Dieser Anschluss ist ausschließlich für Verstärker gedacht.
Schließen Sie nichts anderes daran an. Andernfalls kann das
Gerät beschädigt werden.
An Schnittstellenkabel eines Autotelefons
Warnung
Wenn Sie eine Motorantenne ohne Relaiskästchen verwenden,
kann durch Anschließen dieses Geräts mit dem mitgelieferten
Stromversorgungskabel
die Antenne beschädigt werden.
Hinweise zu den Steuer- und Stromversorgungsleitungen
• Die Motorantennen-Steuerleitung (blau) liefert +12 V Gleichstrom,
wenn Sie den Tuner einschalten oder die AF- (Alternativfrequenzen)
oder die TA-Funktion (Verkehrsdurchsagen) aktivieren.
• Wenn das Fahrzeug mit einer in der Heck-/Seitenfensterscheibe
integrierten FM (UKW)/MW/LW-Antenne ausgestattet ist,
schließen Sie die Motorantennen-Steuerleitung (blau) oder die
Zubehörstromversorgungsleitung (rot) an den Stromversor-
gungsanschluss des vorhandenen Antennenverstärkers an.
Näheres dazu erfahren Sie bei Ihrem Händler.
• Es kann nur eine Motorantenne mit Relaiskästchen
angeschlossen werden.
Stromversorgung des Speichers
Wenn die gelbe Stromversorgungsleitung angeschlossen ist, wird
der Speicher stets (auch bei ausgeschalteter Zündung) mit Strom
versorgt.
Hinweise zum Lautsprecheranschluss
Hinweise zum Lautsprecheranschluss
• Schalten Sie das Gerät aus, bevor Sie die Lautsprecher
anschließen.
• Verwenden Sie Lautsprecher mit einer Impedanz zwischen 4 und
8 Ohm und ausreichender Belastbarkeit. Ansonsten können die
Lautsprecher beschädigt werden.
• Verbinden Sie die Lautsprecheranschlüsse nicht mit dem
Wagenchassis und verbinden Sie auch nicht die Anschlüsse des
rechten mit denen des linken Lautsprechers.
• Verbinden Sie die Masseleitung dieses Geräts nicht mit dem
negativen (–) Lautsprecheranschluss.
• Versuchen Sie nicht, Lautsprecher parallel anzuschließen.
• An die Lautsprecheranschlüsse dieses Geräts dürfen nur
Passivlautsprecher angeschlossen werden. Schließen Sie keine
Aktivlautsprecher (Lautsprecher mit eingebauten Verstärkern) an,
da das Gerät sonst beschädigt werden könnte.
• Um Fehlfunktionen zu vermeiden, verwenden Sie nicht die im
Fahrzeug installierten, integrierten Lautsprecherleitungen, wenn
am Ende eine gemeinsame negative (–) Leitung für den rechten
und den linken Lautsprecher verwendet wird.
• Verbinden Sie nicht die Lautsprecherkabel des Geräts miteinander.
Hinweis zum Anschließen
Hinweis zum Anschließen
Wenn Lautsprecher und Verstärker nicht richtig angeschlossen sind,
erscheint „FAILURE“ im Display. Vergewissern Sie sich in diesem
Fall, dass Lautsprecher und Verstärker richtig angeschlossen sind.
Attenzione
Assicurarsi di installare l’apparecchio nel cruscotto
dell’auto, poiché la parte posteriore dell’apparecchio
stesso si surriscalda durante l’uso.
• Questo apparecchio è stato progettato per l’uso solo a 12
V CC con massa negativa.
• Evitare che i cavi rimangano bloccati da una vite o
incastrati nelle parti mobili (ad esempio nelle guide
scorrevoli dei sedili).
• Prima di effettuare i collegamenti, spegnere il motore
dell’automobile onde evitare di causare cortocircuiti.
• Collegare il cavo di collegamento dell’alimentazione
all’apparecchio e ai diffusori prima di collegarlo al
connettore di alimentazione accessoria.
• Portare tutti i cavi di massa a un punto di massa
comune.
• Per sicurezza, assicurarsi di isolare qualsiasi cavo non
collegato utilizzando del nastro adesivo.
• Non ostruire le prese di ventilazione o i dispersori di
calore dell’apparecchio.
Note sul cavo di alimentazione (giallo)
• Se questo apparecchio viene collegato in combinazione
con altri componenti stereo, la potenza nominale dei
circuiti dell’automobile deve essere superiore a quella
prodotta dalla somma dei fusibili di ciascun componente.
• Se la potenza nominale dei circuiti dell’automobile non
è sufficiente, collegare l’apparecchio direttamente alla
batteria.
Elenco dei componenti
• I numeri nella lista corrispondono a quelli riportati nelle
istruzioni.
• La staffa
e la cornice di protezione vengono
applicati all’apparecchio in fabbrica. Prima di installare
l’apparecchio, utilizzare le chiavette di rilascio
per
rimuovere la staffa
e la cornice di protezione
dall’apparecchio. Per ulteriori informazioni, vedere
“Rimozione della staffa e della cornice di protezione
(
)” sul lato opposto del foglio.
• Conservare le chiavette di rilascio
per un uso
futuro in quanto sono necessarie per rimuovere
l’apparecchio dall’auto.
Attenzione
Maneggiare la staffa
con cautela per evitare di ferirsi le
mani.
Fermo
Nota
Prima di installare l’apparecchio, accertarsi di ripiegare i fermi
presenti su entrambi i lati della staffa
verso l’interno di 2 mm. Se
i fermi sono diritti o ripiegati verso l’esterno, l’apparecchio non verrà
installato in modo sicuro e potrebbe fuoriuscire.
Esempio di collegamento
Note
• Assicurarsi di collegare il cavo di terra prima di collegare
l’amplificatore.
• L’allarme viene emesso solo se è in uso l’amplificatore
incorporato.
Schema di collegamento
A AMP REMOTE IN di un amplificatore di
potenza opzionale
Questo collegamento è riservato esclusivamente agli
amplificatori. Non collegare un tipo di sistema diverso onde
evitare di causare danni all’apparecchio.
Al cavo di interfaccia di un telefono per auto
Avvertenza
Quando si collega l’apparecchio con il cavo di
alimentazione in dotazione
, si potrebbe danneggiare
l’antenna elettrica se questa non dispone di scatola a relè.
Note sui cavi di controllo e di alimentazione
• Il cavo (blu) di controllo dell’antenna elettrica fornisce
alimentazione pari a +12 V CC quando si attiva il sintonizzatore
oppure la funzione TA (notiziario sul traffico) o AF (frequenza
alternativa).
• Se l’automobile è dotata di antenna FM/MW/LW incorporata
nel vetro posteriore/laterale, collegare il cavo (blu) di
controllo dell’antenna elettrica o il cavo (rosso) di ingresso
dell’alimentazione accessoria al terminale di alimentazione del
preamplificatore dell’antenna esistente. Per ulteriori informazioni,
consultare il proprio fornitore.
• Non è possibile usare un’antenna elettrica senza scatola a relè
con questo apparecchio.
Collegamento per la conservazione della memoria
Quando il cavo di ingresso alimentazione giallo è collegato, viene
sempre fornita alimentazione al circuito di memoria anche quando
l’interruttore di accensione è spento.
Note sul collegamento dei diffusori
Note sul collegamento dei diffusori
• Prima di collegare i diffusori spegnere l’apparecchio.
• Usare diffusori di impedenza compresa tra 4 e 8 ohm e con
capacità di potenza adeguata, altrimenti i diffusori potrebbero
venire danneggiati.
• Non collegare i terminali del sistema diffusori al telaio dell’auto e
non collegare i terminali del diffusore destro a quelli del diffusore
sinistro.
• Non collegare il cavo di terra di questo apparecchio al terminale
negativo (–) del diffusore.
• Non collegare i diffusori in parallelo.
• Assicurarsi di collegare soltanto diffusori passivi, poiché il
collegamento di diffusori attivi, dotati di amplificatori incorporati, ai
terminali dei diffusori potrebbe danneggiare l’apparecchio.
• Per evitare problemi di funzionamento, non utilizzare i cavi dei
diffusori incorporati installati nell’automobile se l’apparecchio
condivide un cavo comune negativo (–) per i diffusori destro e
sinistro.
• Non collegare fra loro i cavi dei diffusori dell’apparecchio.
Nota sui collegamenti
Nota sui collegamenti
Se l’amplificatore e il diffusore non sono collegati correttamente,
“FAILURE” viene visualizzato nel display. In tal caso, accertarsi che
l’amplificatore e il diffusore siano collegati correttamente.
Cautions
Be sure to install this unit in the dashboard of the car as
the rear side of the unit becomes hot during use.
• This unit is designed for negative ground (earth) 12 V DC
operation only.
• Do not get the leads under a screw, or caught in moving
parts (e.g. seat railing).
• Before making connections, turn the car ignition off to
avoid short circuits.
• Connect the power connecting lead
to the unit and
speakers before connecting it to the auxiliary power
connector.
• Run all ground (earth) leads to a common
ground (earth) point.
• Be sure to insulate any loose unconnected leads with
electrical tape for safety.
• Do not cover the ventilation slots or heat sinks of the unit.
Notes on the power supply lead (yellow)
Notes on the power supply lead (yellow)
• When connecting this unit in combination with other
stereo components, the connected car circuit’s rating must
be higher than the sum of each component’s fuse.
• When no car circuits are rated high enough, connect the
unit directly to the battery.
Parts Iist
• The numbers in the list are keyed to those in the
instructions.
• The bracket
and the protection collar are attached
to the unit before shipping. Before mounting the unit,
use the release keys
to remove the bracket and
the protection collar
from the unit. For details, see
“Removing the protection collar and the bracket (
)” on
the reverse side of the sheet.
• Keep the release keys
for future use as they
are also necessary if you remove the unit from
your car.
Caution
Handle the bracket
carefully to avoid injuring your
fingers.
Catch
Note
Before installing, make sure that the catches on both sides of the
bracket
are bent inwards 2 mm (
3
/
32
in). If the catches are straight
or bent outwards, the unit will not be installed securely and may
spring out.
Connection example
Notes
• Be sure to connect the ground (earth) lead before connecting the
amplifier.
• The alarm will only sound if the built-in amplifier is used.
Connection diagram
To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting any other
system may damage the unit.
To the interface cable of a car telephone
Warning
If you have a power aerial without a relay box, connecting
this unit with the supplied power connecting lead
may
damage the antenna (aerial).
Notes on the control and power supply leads
• The power antenna (aerial) control lead (blue) supplies +12 V
DC when you turn on the tuner, or when you activate the AF
(Alternative Frequency) or TA (Traffic Announcement) function.
• When your car has built-in FM/MW/LW antenna (aerial) in the
rear/side glass, connect the power antenna (aerial) control lead
(blue) or the accessory power input lead (red) to the power
terminal of the existing antenna (aerial) booster. For details,
consult your dealer.
• A power antenna (aerial) without a relay box cannot be used with
this unit.
Memory hold connection
When the yellow power input lead is connected, power will always
be supplied to the memory circuit even when the ignition switch is
turned off.
Notes on speaker connection
Notes on speaker connection
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms, and with
adequate power handling capacities to avoid its damage.
• Do not connect the speaker terminals to the car chassis, or
connect the terminals of the right speakers with those of the left
speaker.
• Do not connect the ground (earth) lead of this unit to the negative
(–) terminal of the speaker.
• Do not attempt to connect the speakers in parallel.
• Connect only passive speakers. Connecting active speakers (with
built-in amplifiers) to the speaker terminals may damage the unit.
• To avoid a malfunction, do not use the built-in speaker leads
installed in your car if the unit shares a common negative (–) lead
for the right and left speakers.
• Do not connect the unit’s speaker leads to each other.
Note on connection
Note on connection
If speaker and amplifier are not connected correctly, “FAILURE”
appears in the display. In this case, make sure the speaker and
amplifier are connected correctly.
*
1
from car antenna (aerial)
von Autoantenne
de l’antenne de la voiture
dall’antenna dell’auto
van een auto-antenne
von Autoantenne
de l’antenne de la voiture
dall’antenna dell’auto
van een auto-antenne
Fuse (10 A)
Sicherung (10 A)
Fusible (10 A)
Fusibile (10 A)
Zekering (10 A)
Sicherung (10 A)
Fusible (10 A)
Fusibile (10 A)
Zekering (10 A)
AMP REM
Light blue
Hellblau
Bleu ciel
Azzurro
Lichtblauw
Hellblau
Bleu ciel
Azzurro
Lichtblauw
Blue/white striped
Blauweiß gestreift
Rayé bleu/blanc
Rigato blu e bianco
Blauw/wit gestreept
Blauweiß gestreift
Rayé bleu/blanc
Rigato blu e bianco
Blauw/wit gestreept
from the car’s power connector
vom Stromanschluss des Fahrzeugs
du connecteur d’alimentation de la voiture
dal connettore di alimentazione dell’auto
van de autovoedingsstekker
vom Stromanschluss des Fahrzeugs
du connecteur d’alimentation de la voiture
dal connettore di alimentazione dell’auto
van de autovoedingsstekker
ATT
See “Power connection diagram” on the reverse side for details.
Näheres dazu finden Sie im „Stromanschlussdiagramm“. Blättern
Sie dazu bitte um.
Voir le « Schéma de raccordement d’alimentation » au verso pour
plus de détails.
Per ulteriori informazioni, vedere “Diagramma dei collegamenti di
alimentazione” che si trova sul retro.
Zie "Voedingsaansluitschema" op de achterkant voor meer details.
Näheres dazu finden Sie im „Stromanschlussdiagramm“. Blättern
Sie dazu bitte um.
Voir le « Schéma de raccordement d’alimentation » au verso pour
plus de détails.
Per ulteriori informazioni, vedere “Diagramma dei collegamenti di
alimentazione” che si trova sul retro.
Zie "Voedingsaansluitschema" op de achterkant voor meer details.
Max. supply current 0.3 A
max. Versorgungsstrom 0,3 A
Courant d’alimentation maximum 0,3 A
Alimentazione massima fornita 0,3 A
Max. voedingsstroom 0,3 A
max. Versorgungsstrom 0,3 A
Courant d’alimentation maximum 0,3 A
Alimentazione massima fornita 0,3 A
Max. voedingsstroom 0,3 A
*
2
Negative polarity positions 2, 4, 6, and 8 have striped leads.
An den negativ gepolten Positionen 2, 4, 6 und 8 befinden sich gestreifte Adern.
Les positions de polarité négative 2, 4, 6 et 8 sont dotées de cordons rayés.
Le posizioni a polarità negativa 2, 4, 6 e 8 hanno cavi rigati.
De posities voor negatieve polariteit (2, 4, 6 en 8) hebben gestreepte kabels.
1
Purple
Violett
Mauve
Violett
Mauve
Viola
Paars
+
Speaker, Rear, Right
Lautsprecher hinten rechts
Haut-parleur, arrière, droit
Diffusore, posteriore, destro
Luidspreker, achter, rechts
5
White
Weiß
Blanc
Bianco
Wit
+
Speaker, Front, Left
Lautsprecher vorne links
Haut-parleur, avant, gauche
Diffusore, anteriore, sinistro
Luidspreker, voor, links
2
–
Speaker, Rear, Right
Lautsprecher hinten rechts
Haut-parleur, arrière, droit
Diffusore, posteriore, destro
Luidspreker, achter, rechts
6
–
Speaker, Front, Left
Lautsprecher vorne links
Haut-parleur, avant, gauche
Diffusore, anteriore, sinistro
Luidspreker, voor, links
3
Grey
Grau
Grau
Gris
Grigio
Grijs
+
Speaker, Front, Right
Lautsprecher vorne rechts
Haut-parleur, avant, droit
Diffusore, anteriore, destro
Luidspreker, voor, rechts
7
Green
Grün
Vert
Verde
Groen
+
Speaker, Rear, Left
Lautsprecher hinten links
Haut-parleur, arrière, gauche
Diffusore, posteriore, sinistro
Luidspreker, achter, links
4
–
Speaker, Front, Right
Lautsprecher vorne rechts
Haut-parleur, avant, droit
Diffusore, anteriore, destro
Luidspreker, voor, rechts
8
–
Speaker, Rear, Left
Lautsprecher hinten links
Haut-parleur, arrière, gauche
Diffusore, posteriore, sinistro
Luidspreker, achter, links
REAR
AUDIO OUT
SUB AUDIO OUT
FRONT AUDIO OUT
*
2
from the car’s speaker connector
vom Lautsprecheranschluss des Fahrzeugs
du connecteur de haut-parleur de la voiture
dal connettore del diffusore dell’auto
van de autoluidsprekerstekker
vom Lautsprecheranschluss des Fahrzeugs
du connecteur de haut-parleur de la voiture
dal connettore del diffusore dell’auto
van de autoluidsprekerstekker
*
3
*
1
Hinweis zum Anschließen der Antenne
Wenn Ihre Fahrzeugantenne der ISO-Norm
(ISO = International Organization
for Standardization - Internationale
Normungsgemeinschaft) entspricht, schließen
Sie sie mithilfe des mitgelieferten Adapters
an. Verbinden Sie zuerst die Fahrzeugantenne
mit dem mitgelieferten Adapter und verbinden
Sie diesen dann mit der Antennenbuchse des
Hauptgeräts.
*
2
Cinchkabel (nicht mitgeliefert)
*
3
Mit dem Kabel nach oben einsetzen
*
1
Note for the antenna (aerial) connecting
If your car antenna (aerial) is an
ISO (International Organisation for
Standardisation) type, use the supplied
adaptor
to connect it. First connect the car
aerial to the supplied adaptor, then connect it
to the antenna (aerial) jack of the master unit.
*
2
RCA pin cord (not supplied)
*
3
Insert with the cord upwards
*
1
Remarque sur le raccordement de l’antenne
Si votre antenne de voiture est de type ISO
(Organisation internationale de normalisation),
utilisez l’adaptateur fourni
pour la
raccorder. Raccordez d’abord l’antenne de
voiture à l’adaptateur fourni et, ensuite, à la
prise d’antenne de l’appareil principal.
*
2
Cordon à broche RCA (non fourni)
*
3
Insérez avec le câble vers le haut
*
1
Nota per il collegamento dell’antenna
Se l’antenna dell’auto è di tipo
ISO (International Organization for
Standardization), utilizzare l’adattatore
in dotazione per collegarla. Collegare prima
l’antenna dell’auto all’adattatore in dotazione,
quindi collegarla alla presa dell’antenna
dell’apparecchio principale.
*
2
Cavo a piedini RCA (non in dotazione)
*
3
Inserire con il cavo rivolto verso l’alto
*
1
Opmerking bij de antenne-aansluiting
Indien uw auto is uitgerust met een antenne
van het type ISO (International Organisation
for Standardization), moet u die aansluiten met
behulp van de bijgeleverde adapter
. Sluit
eerst de auto-antenne aan op de bijgeleverde
adapter en vervolgens de antennestekker op
het hoofdtoestel.
*
2
Tulpstekkersnoer (niet bijgeleverd)
*
3
Plaatsen met het snoer naar boven
Positions 1, 2, 3, and 6 do not have pins.
An Position 1, 2, 3 und 6 befinden sich keine Stifte.
Les positions 1, 2, 3 et 6 ne comportent pas de broches.
Le posizioni 1, 2, 3 e 6 non hanno piedini.
De posities 1, 2, 3 en 6 hebben geen pins.
4
Yellow
Gelb
Jaune
Giallo
Giallo
Geel
continuous power supply
permanente Stromversorgung
alimentation continue
alimentazione continua
continu voeding
7
Red
Rot
Rouge
Rosso
Rosso
Rood
switched power supply
geschaltete Stromversorgung
alimentation commutée
alimentazione commutata
geschakelde voeding
5
Blue
Blau
Bleu
Blau
Bleu
Blu
Blauw
power antenna (aerial) control
Motorantennensteuerung
antenne électrique
comando dell’antenna elettrica
elektrische antenne
8
Black
Schwarz
Noir
Nero
Zwart
ground (earth)
Masse
masse
masse
terra
aarding
*
2
Click on the first or last page to see other MEX-BT3600U service manuals if exist.