Sony EXR-C205 / XR-C340 (serv.man3) Service Manual ▷ View online
– 2 –
HOUSING
ARM (SUCTION)
Note:
Follow the assembly procedure in the numerical order given.
A
part
C
part
B
part
D
part
8
Hold the hanger by
bending the claw.
bending the claw.
6
Fit projection on
D
part.
4
Fit claw on
B
part.
3
Put the housing
under
under
A
part.
5
Fit projection on
C
part.
1
Install the catch to the hanger.
2
Install the hanger onto
two claws of the housing.
two claws of the housing.
7
Holder the hanger by bending the claw.
hanger
housing
2
Move the arm (suction) in the arrow
direction and fit on projection.
direction and fit on projection.
1
Fit the arm (suction) on the shaft.
projection
1-1.
ASSEMBLY OF MECHANISM DECK
– 3 –
LEVER (LDG-A) / (LDG-B)
GEAR (LDG-FT)
shaft
A
shaft
B
shaft
C
1
Fit the lever (LDG-A) on
shafts
shafts
A
–
C
and install it.
shaft
A
shaft
B
2
Fit the lever (LDG-B) on
shafts
shafts
A
and
B
and
install it.
3
type-E stop ring 2.0
gear (LDG-D)
5
gear (LDG-FT)
6
polyethylene washer
2
tension spring (LD-2)
2
tension spring (LD-1)
gear (LDG-FB)
lever (LDG-A)
hole
hole
4
Align hole in the gear (LDG-D)
with hole the lever (LDG-A).
with hole the lever (LDG-A).
3
Move the lever (LDG-B)
in the arrow direction.
in the arrow direction.
1
– 4 –
2
guide (C)
1
three claws
GUIDE (C)
two precision screws
(P2
(P2
×
2)
capstan / reel motor
(M901)
(M901)
30˚
MOUNTING POSITION OF CAPSTAN / REEL MOTOR (M901)
– 5 –
– 6 –
1-2.
EXPLODED VIEW
• Items marked “*” are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering
these items.
delay should be anticipated when ordering
these items.
• The mechanical parts with no reference num-
ber in the exploded views are not supplied.
NOTE:
• -XX and -X mean standardized parts, so they
may have some difference from the original
one.
one.
• Color Indication of Appearance Parts
Example:
KNOB, BALANCE (WHITE) . . . (RED)
KNOB, BALANCE (WHITE) . . . (RED)
↑
↑
Parts Color Cabinet's Color
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Description
Remark
MECHANISM DECK SECTION
(MG-25F-136)
(MG-25F-136)
151
A-3291-667-A CLUTCH (FR) ASSY
* 152
3-019-130-01 LEVER (LDG-A)
* 153
3-019-131-01 LEVER (LDG-B)
154
3-020-539-01 SPRING (LD-1), TENSION
155
3-020-540-01 SPRING (LD-2), TENSION
156
3-020-542-01 GEAR (LOADING FT)
157
3-341-753-11 WASHER, POLYETHYLENE
158
3-020-533-01 HOUSING
* 159
3-020-532-01 ARM (SUCTION)
160
3-020-534-01 HANGER
161
3-933-346-01 CATCHER
162
3-933-344-01 GUIDE (C)
163
3-014-798-01 SCREW (HEAD), SPECIAL
164
3-364-151-01 WASHER
165
A-3301-267-A CHASSIS ASSY (F)
166
3-017-302-01 BELT (25)
167
3-936-853-01 FLYWHEEL (F)
168
3-701-437-21 WASHER
HP901
1-500-157-21 HEAD, MAGNETIC (PLAYBACK)
M901
A-3291-665-A MOTOR ASSY, MAIN (CAPSTAN/REEL)
#6
7-624-104-04 STOP RING 2.0 TYPE-E
#7
7-627-553-17 PRECISION SCREW +P 2X2 TYPE3
160
161
162
164
165
166
167
151
168
168
159
158
155
156
157
154
153
152
163
HP901
M901
#7
#6
A
A
2.
MAIN BOARD MODIFICATION
•
New/Former Discrimination
Former type: 1-664-751-11
New type : 1-664-751-12
New type : 1-664-751-12
[MAIN BOARD]
(COMPONENT SIDE)
2-1.
NOTE FOR PRINTED WIRING BOARD AND SCHEMATIC DIAGRAM
Note on Schematic Diagram:
• All capacitors are in µF unless otherwise noted. pF: µµF
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
and tantalums.
• All resistors are in
Ω
and
1
/
4
W or less unless otherwise
specified.
•
¢
: internal component.
•
C
: panel designation.
•
U
: B+ Line.
• Power voltage is dc 14.4 V and fed with regulated dc power
supply from battery and accessory terminals.
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : FM
(
no mark : FM
(
) : AM (MW)
〈〈
〉〉
: TAPE PLAYBACK
∗
: Impossible to measure
• Voltages are taken with a VOM (Input impedance 10 M
Ω
).
Voltage variations may be noted due to normal produc-
tion tolerances.
tion tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal produc-
tion tolerances.
tion tolerances.
• Circled numbers refer to waveforms.
• Signal path.
• Signal path.
F
: FM
f
: AM (MW)
E
: TAPE PLAYBACK
L
: BUS AUDIO IN
• Abbreviation
C205 : EXR-C205
C340 : XR-C340
C340 : XR-C340
Note on Printed Wiring Board:
• X
: parts extracted from the component side.
•
p
: parts mounted on the conductor side.
•
¢
: internal component.
• b
: Pattern from the side which enables seeing.
