DOWNLOAD Sony CX-LMN75 / XR-MN75 Service Manual ↓ Size: 7.08 MB | Pages: 71 in PDF or view online for FREE

Model
CX-LMN75 XR-MN75
Pages
71
Size
7.08 MB
Type
PDF
Document
Service Manual
Brand
Device
Car Audio
File
cx-lmn75-xr-mn75.pdf
Date
PREV: Sony XR-MN75 Service Manual

Sony CX-LMN75 / XR-MN75 Service Manual ▷ View online

17
CX-LMN75
3-19. TIMING BELT (FRONT/REAR)
3-20. CAM (GEAR)
Note: Refer to assembly (Section 4)
2
gear (mode cam)
: Note
1
screw
(PTPWH2.6
 
×
 8)
3
slider (mode cam) assy
5
two gears
(center)
7
two gears (center)
8
timing belt (rear)
9
timing belt (rear)
4
gear
(timing)
6
timing belt
(front)
timing belt 
(rear)
When install three timing belts, 
its pass under each claws.
timing belt 
(rear)
timing belt (front)
claw
claw
claw
claw
qf
cam (gear)
: Note
qs
gear(mode cam)
0
gear (mode C)
:Note
4
gear (mode 5)
8
gear (mode D)
6
gear (mode 5)
1
screw(PTPWH2.6 
×
 8)
7
screw (PTPWH2.6 
×
 8)
9
screw 
    (PTPWH2.6 
×
 8) 
qa
screw 
    (PTPWH2.6 
×
 8) 
3
screw (PTPWH2.6 
×
 8)
5
screw (PTPWH2.6 
×
 8)
2
pulley
(mode deceleration)
qd
screw 
Note: Refer to assembly
         (Section 4).
18
CX-LMN75
3-21. SENSOR BOARD
ql
harness
qd
gear (eject lock)
q;
cam (eject lock)
     : Note  
qh
two claws
qj
rotary encoder
(S771)
qf
gear 
(mode B)
w;
screw 
     (BVTP2.6 
×
 8)
qg
screw 
(PTPWH2.6 
×
 8)
wa
SENSOR board
8
shaft
(shutter)
7
compression spring 
(shutter)
qs
cam (BU U/D)
qa
screw 
(PTPWH2.6 
×
 8)
3
screw 
(BVTP2.6 
×
 8)
1
screw 
(PTPWH2.6 
×
 8)
4
two screws 
(BVTP2.6 
×
 8)
2
lever shutter (A)
5
base (shutter) block
6
gear (mode A)
9
screw 
(PTPWH2.6 
×
 8)
qk
claw
Note: Refer to assembly (Section 4).
19
CX-LMN75
• This set can be assembled in the order shown below.
4-1. HOW TO INSTALL THE CAM (EJECT LOCK)
SECTION 4
ASSEMBLY
4-2. HOW TO INSTALL THE CAM (GEAR)
mark
cam (BU U/D)
cam (eject lock)
– bottom view • front –
gear (eject lock)
1
Rotate the cam (BU U/D) fully in the direction of arrow.
2
Engage the gear (eject lock) and the gear of the cam (eject lock)
aligning the mark with the center of the gear (eject lock).
boss
cam (gear)
mark
cam (BU U/D)
– bottom view • front –
1
Check that the cam (BU U/D) can not be rotated in the direction of arrow.
2
Align the mark on the cam (gear) with the boss as shown in the figure
and install the cam (gear).
20
CX-LMN75
4-3. HOW TO INSTALL THE GEAR (MODE C)
4-4. HOW TO INSTALL THE GEAR (MODE CAM)
1
Align the mark on the rotary encoder (S771) with the projection of  the assy.
2
Check that the cam (BU U/D) can not be rotated in the direction of arrow.
3
Install the gear (
mode
 C)
– bottom view • front –
gear (
mode
 C)
rotary encoder
(S771)
cam (BU U/D)
mark
projection
chassis
mark 
B
slider (mode cam) assy
shaft
mark 
A
mark 
D
gear (mode cam)
cam (gear)
mark 
C
1
Slide the shaft in the direction of arrow.
2
Align mark 
A
 on the gear (mode cam) with mark 
B
 on the slider (mode cam) assy, 
then install the gear (mode cam).
3
Check that mark 
C
 on the gear (mode cam) is in alignment with mark 
D
 on the cam (gear).
– bottom view • front –
Page of 71
Display

Click on the first or last page to see other CX-LMN75 / XR-MN75 service manuals if exist.

RANDOM: