Sony CX-LMN5 / XR-MN5 Service Manual ▷ View online
17
CX-LMN5
3-21. SENSOR Board
ql
harness
qd
gear (eject lock)
q;
cam (eject lock)
: Note
qh
two claws
qj
rotary encoder
(S771)
(S771)
qf
gear
(mode B)
(mode B)
w;
screw
(BVTP2.6
×
8)
qg
screw
(PTPWH2.6
(PTPWH2.6
×
8)
wa
SENSOR board
8
shaft
(shutter)
(shutter)
7
compression spring
(shutter)
(shutter)
qs
cam (BU U/D)
qa
screw
(PTPWH2.6
(PTPWH2.6
×
8)
3
screw
(BVTP2.6
(BVTP2.6
×
8)
1
screw
(PTPWH2.6
(PTPWH2.6
×
8)
4
two screws
(BVTP2.6
(BVTP2.6
×
8)
2
lever shutter (A)
5
base (shutter) block
6
gear (mode A)
9
screw
(PTPWH2.6
(PTPWH2.6
×
8)
qk
claw
Note: Refer to assembly (Section 4).
18
CX-LMN5
• This set can be assembled in the order shown below.
4-1. How to Install the Cam (EJECT LOCK)
SECTION 4
ASSEMBLY
4-2. How to Install the Cam (GEAR)
mark
cam (BU U/D)
cam (eject lock)
– bottom view • front –
gear (eject lock)
1
Rotate the cam (BU U/D) fully in the direction of arrow.
2
Engage the gear (eject lock) and the gear of the cam (eject lock)
aligning the mark with the center of the gear (eject lock).
aligning the mark with the center of the gear (eject lock).
boss
cam (gear)
mark
cam (BU U/D)
– bottom view • front –
1
Check that the cam (BU U/D) can not be rotated in the direction of arrow.
2
Align the mark on the cam (gear) with the boss as shown in the figure
and install the cam (gear).
and install the cam (gear).
19
CX-LMN5
4-3. How to Install the Gear (MODE C)
4-4. How to Install the Gear (MODE CAM)
1
Align the mark on the rotary encoder (S771) with the projection of the assy.
2
Check that the cam (BU U/D) can not be rotated in the direction of arrow.
3
Install the gear (
mode
C)
– bottom view • front –
gear (
mode
C)
rotary encoder
(S771)
(S771)
cam (BU U/D)
mark
projection
chassis
mark
B
slider (mode cam) assy
shaft
mark
A
mark
D
gear (mode cam)
cam (gear)
mark
C
1
Slide the shaft in the direction of arrow.
2
Align mark
A
on the gear (mode cam) with mark
B
on the slider (mode cam) assy,
then install the gear (mode cam).
3
Check that mark
C
on the gear (mode cam) is in alignment with mark
D
on the cam (gear).
– bottom view • front –
20
CX-LMN5
4-5. How to Install the Rotary Encoder (S702), Gear (STOCKER COMMUNICATION)
4-6. How to Install the Stocker Assy
2
five solders
6
two gears
(stocker communication)
(stocker communication)
4
gear
(stocker communication)
(stocker communication)
CONNECTOR board
7
two screws
(PTPWH2.6
×
8)
5
screw
(PTPWH2.6
×
8)
3
screw
(PWH2
×
6)
rotary encoder
(S702)
(S702)
gear
(stocker
communication)
(stocker
communication)
– rear –
1
rotary encoder
(S702)
(S702)
Engage the rotary encoder (S702)
and the gear (stocker communication)
as shown below in the figure.
and the gear (stocker communication)
as shown below in the figure.
2
cam
(stocker V)
3
screw
(PTPWH2.6
×
8)
4
two cams
(stocker U/D)
5
two screws
(PTPWH2.6
×
8)
boss
boss
rotary encoder
(S702)
(S702)
Install the stocker assy
fitting three bosses into the
each groove of cam
then fix by rotating the cams
in the direction of arrow.
fitting three bosses into the
each groove of cam
then fix by rotating the cams
in the direction of arrow.
hole
gear
(stocker communication)
(stocker communication)
– rear –
screw
1
Position the hole on the gear
(stocker communication) on the
screw of the rotary encoder (S702).
(stocker communication) on the
screw of the rotary encoder (S702).
To install three cams, align each groove
of the cam with each
of the cam with each
f
mark on the
chassis as shown in the figure.
cam
Click on the first or last page to see other CX-LMN5 / XR-MN5 service manuals if exist.