Sony CDX-L410X Service Manual ▷ View online
9
CDX-L410X
2-6. LEVER SECTION, IN SELF SW BOARD
2-7. SERVO BOARD
4
claws
2
IN SELF SW board
7
lever (L)
3
tension spring (LR)
6
lever (R)
5
guide (disc)
1
special screw
6
special screws
1
CN3
2
Removal the solders.
4
P 2x3
5
loading motor assy
8
SERVO board
7
special screw
9
connector
optical pick-up block
3
Unsolder the
lead wires.
black
yellow
10
CDX-L410X
1
tension spring (KF1)
7
compression spring (FL)
6
floating block assy
8
compression spring (FL)
4
Fit lever (D) in the
direction of the arrow.
2
damper (T)
3
damper (T)
5
Turn loading ring in the
direction of the arrow.
2-9. FLOATING BLOCK ASSY
2-8. SHAFT ROLLER ASSY, LOAD SW BOARD
• When installing, take note of the positions
arm (roller) and washers. (Fig. 1)
arm (roller) and washers. (Fig. 1)
Fig. 1
1
tension spring (RA)
2
arm (roller)
3
retaing ring (RA)
4
shaft retainer (roller)
5
shaft roller assy
6
special screw
7
LOAD SW board
retaing ring
(RA)
(RA)
arm
arm
washer
washer
shaft retainer
(roller)
(roller)
shaft retainer (roller)
11
CDX-L410X
1
P 2x3
4
screw
5
plate spring (feed)
6
shaft (feed) assy
2
sled motor assy
3
optical pick-up block
2-10. OPTICAL PICK-UP BLOCK
12
CDX-L410X
3-1. IC PIN DESCRIPTION
• IC801 µPD780076YGK-R24 (SYSTEM CONTROL) (MAIN Board)
Pin No.
Pin Name
I/O
Pin Description
1
D SW
I
Down switch detection signal input “L”: Down switch on
2
LM LD
O
Loading motor drive control signal output (Loading direction)
3
LM EJ
O
Loading motor drive control signal output (Eject direction)
4
ATT
O
Mute control signal output of audio signal line “H”: mute on
5
A ATT
O
Mute control signal output to power amp IC (IC101) “L”: amp mute on
6
PLL DI
I
Serial data signal input to PLL IC (IC601)
7
VOL ATT
O
Mute control signal output to Electric volume IC (IC401)
8
DOOR SW/IND
I
Door switch signal input Case of flipdown, sense to open condition of door “H”: open
9
VSS0
—
Ground pin
10
VDD0
—
Power supply pin
11
PLL CE
O
Chip enable signal output to PLL IC (IC601)
12
BEEP
O
Beep signal output of key beep, caution alarm to power amp IC (IC101)
13
SDAO
O
IIC data line signal output (control to electric volume IC (IC401))
14
SCLO
O
IIC clock line signal output (control to electric volume IC (IC401))
15
LCD CE
O
Chip enable control signal output to LCD driver IC (IC901)
16
LCD DO
O
Serial data signal output to LCD driver IC (IC901)
17
LCD CLK
O
Serial clock signal output to LCD driver IC (IC901)
18
BUS SI
I
SONY bus data signal input
19
BUS SO
O
SONY bus data signal output
20
BUS CLK
I
SONY bus clock signal input
21
BUS CLK GEN
O
SONY bus clock signal output
22
AM ON
O
AM select signal output
FM circuit power supply control output of tuner unit (TU601) “H”: FM on
23
FM ON
O
FM select signal output
FM circuit power supply control output of tuner unit (TU601) “H”: FM on
24
VDD1
—
Power supply pin
25
AVSS
—
Ground pin
Stereo signal input/monaural control signal output
26
ST IND
I/O
At forced monaural on: “L” output
At forced monaural off: input mode, stereo on for “L” input
27
SHIFT/PH1
I
Rotary commander shift key signal input Not used in this set.
28
S METER
I
S meter signal input from tuner unit (TU601)
29, 30
KEY0, KEY1
I
A/D key signal input Input of A/D key matrix and front panel attachment decision.
31
R COM
I
Rotary commander AD level signal input
Sense to key voltage level of rotary commander
32
DST SEL
I
Destination select input
33
TEST
I
Test mode select signal input “L”: test mode
34
AVREF
—
Analog reference voltage pin
35
AD ON
O
LCD INHIBIT signal output Not used in this set.
36
RESET
I
Reset signal input from reset IC (IC902) “H”: reset
37
XT2
—
Connect to sub clock (32.768 kHz)
38
XT1
—
Connect to sub clock (32.768 kHz)
39
IC
—
At on board writer: 12 V power supply pin (usually ground pin)
40
X2
—
Connect to crystal oscillator (8.38 MHz)
41
X1
—
Connect to crystal oscillator (8.38 MHz)
42
VSS1
—
Ground pin
43
KEY ACK
I
Key acknowledge signal input
44
SIRCS
I
Wireless remote control signal input from remote control receiver IC (IC951)
45
SELF SW
I
SELF switch detection signal input “L”: SELF switch on
46
BU IN
I
Backup power supply detection signal input
47
NOSE
I
Front panel attachment detection signal input from SW801 “L”: panel on
SECTION 3
DIAGRAMS
Click on the first or last page to see other CDX-L410X service manuals if exist.