Sony CDX-GT517EE Service Manual ▷ View online
5
CDX-GT517EE
SECTION 2
GENERAL
• LOCATION OF CONTROLS
• CONNECTIONS
This section is extracted
from instruction manual.
from instruction manual.
6
Location of controls and basic operations
Main unit
Front panel removed
Card remote commander
RM-X151
RM-X151
Refer to the pages listed for details. The
corresponding buttons on the card remote
commander control the same functions as those
on the unit.
corresponding buttons on the card remote
commander control the same functions as those
on the unit.
A OFF button
To power off; stop the source.
B DSO button 4
To select the DSO mode (1, 2, 3 or OFF).
The larger the number, the more enhanced
the effect.
The larger the number, the more enhanced
the effect.
C Volume control dial/select button 11
To adjust volume (rotate); select setup items
(press and rotate).
(press and rotate).
D SOURCE button
To power on; change the source (Radio/CD/
MD*
MD*
1
/AUX).
E Display window
F AUX input jack 12
To connect a portable audio device.
G OPEN button 5
OFF
OPEN
DSPL
AF/TA
SEEK
SEEK
PAUSE
GP/ALBM
REP
SHUF
AUX
PUSH SELECT
1
2
3
4
5
6
MODE
DSO
PTY
EQ3
SOURCE
1
q;
9
qa
qd
qg
qs
2
qf
4
5
8
6 7
3
CDX-GT517EE
RESET
qj
qk
qh
OFF
DSPL
SCRL
SEL
SOURCE
MODE
1
3
2
4
6
5
ATT
VOL
+
–
+
–
4
ws
qs
1
ql
qd
wa
w;
wg
wd
wf
7
H EQ3 (equalizer) button 11
To select an equalizer type (XPLOD,
VOCAL, EDGE, CRUISE, SPACE,
GRAVITY, CUSTOM or OFF).
VOCAL, EDGE, CRUISE, SPACE,
GRAVITY, CUSTOM or OFF).
I Receptor for the card remote
commander
J SEEK –/+ buttons
CD:
To skip tracks (press); skip tracks
continuously (press, then press again within
about 1 second and hold); reverse/fast-
forward a track (press and hold).
Radio:
To tune in stations automatically (press); find
a station manually (press and hold).
To skip tracks (press); skip tracks
continuously (press, then press again within
about 1 second and hold); reverse/fast-
forward a track (press and hold).
Radio:
To tune in stations automatically (press); find
a station manually (press and hold).
K PTY (Program Type) button 10
To select PTY in RDS.
L MODE button 8, 12
To select the radio band (FM/MW/LW);
select the unit*
select the unit*
2
.
M DSPL (display) button 8, 9
To change display items.
N Number buttons
CD/MD*
1
:
(1)/(2): GP*
3
/ALBM*
4
—/
+
To skip albums (press); skip albums
continuously (press and hold).*
continuously (press and hold).*
5
(3): REP 8, 13
(4): SHUF 8, 13
(6): PAUSE*
(4): SHUF 8, 13
(6): PAUSE*
6
To pause playback. To cancel, press
again.
again.
Radio:
To receive stored stations (press); store
stations (press and hold).
To receive stored stations (press); store
stations (press and hold).
O AF (Alternative Frequencies)/TA
(Traffic Announcement) button 9
To set AF and TA in RDS.
To set AF and TA in RDS.
P RESET button 4
Q Z (eject) button 5
To eject the disc.
R Disc slot 5
To insert the disc.
The following buttons on the card remote
commander have also different buttons/functions
from the unit. Remove the insulation film before
use (page 4).
commander have also different buttons/functions
from the unit. Remove the insulation film before
use (page 4).
ql < (.)/, (>) buttons
To control CD/radio, the same as (SEEK)
—/
—/
+ on the unit.
w; VOL (volume) +/– button
To adjust volume.
wa ATT (attenuate) button
To attenuate the sound. To cancel, press
again.
again.
ws SEL (select) button
The same as the select button on the unit.
wd M (+)/m (–) buttons
To control CD, the same as (1)/(2)
(GP/ALBM —/
(GP/ALBM —/
+) on the unit.
wf SCRL (scroll) button 8
To scroll the display item.
wg Number buttons
To receive stored stations (press); store
stations (press and hold).
stations (press and hold).
*1 When an MD changer is connected.
*2 When a CD/MD changer is connected.
*3 When an ATRAC CD is played.
*4 When an MP3/WMA/AAC is played.
*5 If the changer is connected, the operation is
*2 When a CD/MD changer is connected.
*3 When an ATRAC CD is played.
*4 When an MP3/WMA/AAC is played.
*5 If the changer is connected, the operation is
different, see page 13.
*6 When playing back on this unit.
Note
If the unit is turned off and the display disappears, it
cannot be operated with the card remote commander
unless (SOURCE) on the unit is pressed, or a disc is
inserted to activate the unit first.
If the unit is turned off and the display disappears, it
cannot be operated with the card remote commander
unless (SOURCE) on the unit is pressed, or a disc is
inserted to activate the unit first.
Tip
For details on how to replace the battery, see
“Replacing the lithium battery of the card remote
commander” on page 16.
For details on how to replace the battery, see
“Replacing the lithium battery of the card remote
commander” on page 16.
AUDIO OUT REAR
*
BUS AUDIO IN
BUS CONTROL IN
A
B
BUS AUDIO IN
BUS CONTROL IN
Source selector*
*
XA-C40
* not supplied
* AUDIO OUT SUB/REAR
Connection example
Notes (2-A)
•
•
Be sure to connect the ground (earth) lead before connecting
the amplifi er.
•
The alarm will only sound if the built-in amplifi er is used.
Tip (2-B- )
For connecting two or more CD/MD changers, the source
selector XA-C40 (not supplied) is necessary.
For connecting two or more CD/MD changers, the source
selector XA-C40 (not supplied) is necessary.
(2-A)
(2-B- )
6
CDX-GT517EE
BUS AUDIO IN
AUDIO OUT
FRONT
BUS
CONTROL IN
REMOTE
IN
AUDIO OUT REAR
*
3
L
R
AUDIO
OUT
REAR
AUDIO
OUT
FRONT
BUS
AUDIO
IN
1
3
5
7
2
4
6
8
5
7
4
8
6
Negative polarity positions 2, 4, 6, and 8 have striped leads.
1
Purple
+
Speaker, Rear, Right
5
White
+
Speaker, Front, Left
2
–
Speaker, Rear, Right
6
–
Speaker, Front, Left
3
Grey
+
Speaker, Front, Right
7
Green
+
Speaker, Rear, Left
4
–
Speaker, Front, Right
8
–
Speaker, Rear, Left
AMP REM
Max. supply current 0.3 A
Fuse (10 A)
Blue/white striped
3
*
2
Light blue
2
from the car’s power connector
See “Power connection diagram” on the reverse
side for details.
side for details.
*
1
Note for the antenna (aerial) connecting
If your car antenna (aerial) is an ISO (International
Organization for Standardization) type, use the
supplied adaptor 2 to connect it. First connect
the car antenna (aerial) to the supplied adaptor,
then connect it to the antenna (aerial) jack of the
master unit.
Organization for Standardization) type, use the
supplied adaptor 2 to connect it. First connect
the car antenna (aerial) to the supplied adaptor,
then connect it to the antenna (aerial) jack of the
master unit.
*
2
RCA pin cord (not supplied)
*
3
AUDIO OUT can be switched SUB or REAR. For
details, see the Operating Instructions.
details, see the Operating Instructions.
*
4
Insert with the cord upwards
*
5
Supplied with the CD/MD changer
*
1
2
*
2
*
3
*
4
*
5
Positions 1, 2, 3, and 6 do not have pins.
from the car’s speaker
connector
connector
ATT
from car antenna (aerial)
*
2
Source selector
(not supplied)
XA-C40
*
4
*
1
Supplied with XA-C40
XA-C40
4
Yellow
continuous power supply
7
Red
switched power supply
5
Blue
power antenna (aerial) control
8
Black
ground (earth)
6
Orange/White
switched illumination power supply
*
5
Connection diagram
A
To AMP REMOTE IN of an optional power
amplifi er
This connection is only for amplifi ers. Connecting any other
system may damage the unit.
system may damage the unit.
B
To the interface cable of a car telephone
Warning
If you have a power antenna (aerial) without a relay box,
connecting this unit with the supplied power supply lead
3
connecting this unit with the supplied power supply lead
3
may damage the antenna (aerial).
Notes on the control and power supply leads
•
•
The power antenna (aerial) control lead (blue) supplies +12 V
DC when you turn on the tuner, or when you activate the AF
(Alternative Frequency) or TA (Traffi c Announcement) function.
(Alternative Frequency) or TA (Traffi c Announcement) function.
•
When your car has built-in FM/MW/LW antenna (aerial) in the
rear/side glass, connect the power antenna (aerial) control
lead (blue) or the accessory power input lead (red) to the
power terminal of the existing antenna (aerial) booster. For
details, consult your dealer.
lead (blue) or the accessory power input lead (red) to the
power terminal of the existing antenna (aerial) booster. For
details, consult your dealer.
•
A power antenna (aerial) without a relay box cannot be used
with this unit.
Memory hold connection
When the yellow power input lead is connected, power will
always be supplied to the memory circuit even when the ignition
switch is turned off.
When the yellow power input lead is connected, power will
always be supplied to the memory circuit even when the ignition
switch is turned off.
Notes on speaker connection
•
•
Before connecting the speakers, turn the unit off.
•
Use speakers with an impedance of 4 to 8 ohms, and with
adequate power handling capacities to avoid its damage.
•
Do not connect the speaker terminals to the car chassis, or
connect the terminals of the right speakers with those of the
left speaker.
left speaker.
•
Do not connect the ground (earth) lead of this unit to the
negative (–) terminal of the speaker.
•
Do not attempt to connect the speakers in parallel.
•
Connect only passive speakers. Connecting active speakers
(with built-in amplifi ers) to the speaker terminals may damage
the unit.
the unit.
•
To avoid a malfunction, do not use the built-in speaker leads
installed in your car if the unit shares a common negative (–)
lead for the right and left speakers.
lead for the right and left speakers.
•
Do not connect the unit’s speaker leads to each other.
Note on connection
If speaker and amplifi er are not connected correctly, “FAILURE”
appears in the display. In this case, make sure the speaker and
amplifi er are connected correctly.
If speaker and amplifi er are not connected correctly, “FAILURE”
appears in the display. In this case, make sure the speaker and
amplifi er are connected correctly.
A
B
3
7
CDX-GT517EE
SECTION 3
DISASSEMBLY
Note: This set can be disassemble according to the following sequence.
3-1.
SUB PANEL ASSY
(Page 8)
(Page 8)
3-2.
CD MECHANISM BLOCK
(Page 8)
(Page 8)
SET
3-3.
MAIN BOARD
(Page 9)
(Page 9)
3-5.
CHASSIS (T) SUB ASSY
(Page 10)
(Page 10)
3-6.
ROLLER ARM ASSY
(Page 10)
(Page 10)
3-7.
CHASSIS (OP) ASSY
(Page 11)
(Page 11)
3-4.
SERVO BOARD
(Page 9)
(Page 9)
1. CHUCKING ARM SUB ASSY
(SUPPLEMENT-1 Page 1)
2. SLED MOTOR ASSY
(SUPPLEMENT-1 Page 2)
3. OPTICAL PICK-UP SECTION
(SUPPLEMENT-1 Page 3)
4. OPTICAL PICK-UP
(SUPPLEMENT-1 Page 3)
Ver. 1.1
8
CDX-GT517EE
3-2. CD MECHANISM BLOCK
Note: Follow the disassembly procedure in the numerical order given.
3-1. SUB PANEL ASSY
2
two claws
3
two claws
5
sub panel assy
1
two screws
(+PTT 2.6
×
6)
4
flexible flat cable (20 core)
(CN802)
(CN802)
4
CN350
3
1
screw
(+PTT 2.6
(+PTT 2.6
×
6)
2
screw
(+PTT 2.6
(+PTT 2.6
×
6)
5
two screws
(+PTT 2.6
(+PTT 2.6
×
4)
6
bracket (CD)
7
CD mechanism block
Click on the first or last page to see other CDX-GT517EE service manuals if exist.