DOWNLOAD Sony CDX-GT35U Service Manual ↓ Size: 1.93 MB | Pages: 36 in PDF or view online for FREE

Model
CDX-GT35U
Pages
36
Size
1.93 MB
Type
PDF
Document
Service Manual
Brand
Device
Car Audio
File
cdx-gt35u.pdf
Date

Sony CDX-GT35U Service Manual ▷ View online

SERVICE MANUAL
Sony Corporation
Audio&Video Business Group
Published by Sony Techno Create Corporation
SPECIFICATIONS
FM/AM COMPACT DISC PLAYER
9-889-917-01
2010H04-1
© 
2010.08
US Model
Canadian Model
Ver. 1.0  2010.08
•  The tuner and CD sections have no adjustments.
Model Name Using Similar Mechanism
CDX-GT440U
CD Drive Mechanism Type
MG-101Y-188//Q
Optical Pick-up Name
DAX-25A
Tuner section
FM
Tuning range: 
  87.5 – 107.9 MHz 
Antenna (aerial) terminal:
  External antenna (aerial) connector
Intermediate frequency: 150 kHz
Usable sensitivity: 10 dBf
Selectivity: 75 dB at 400 kHz
Signal-to-noise ratio: 70 dB (mono)
Separation: 40 dB at 1 kHz
Frequency response: 20 – 15,000 Hz
AM 
Tuning range:
 
  530 – 1,710 kHz
Antenna (aerial) terminal:
  External antenna (aerial) connector
Intermediate frequency: 25 kHz
Sensitivity: 26 
μV
CD player section
Signal-to-noise ratio:
 120 dB
Frequency response: 10 – 20,000 Hz
Wow and fl utter: Below measurable limit
USB Player section
Interface:
 USB (Full-speed)
Maximum current: 500 mA
Power amplifi er section
Outputs:
 Speaker outputs
Speaker impedance: 4 – 8 ohms
Maximum power output: 
 52 
× 4 (at 4 ohms)
General
Outputs:
  Audio outputs terminal 
 (sub/rear 
switchable)
  Power antenna (aerial) relay control terminal
 Power 
amplifi er control terminal
Inputs:
  Antenna (aerial) input terminal
  AUX input jack (stereo mini jack)
  USB signal input connector
Tone controls:
  Low: ±10 dB at 60 Hz (XPLOD)
  Mid: ±10 dB at 1 kHz (XPLOD)
  High: ±10 dB at 10 kHz (XPLOD)
Power requirements: 12 V DC car battery
  (negative ground (earth))
Dimensions: Approx. 178 × 50 × 179 mm
 (7 
1
/
8
 × 2 × 7 
1
/
8
 in.) (w/h/d)
Mounting dimensions:
  Approx. 182 × 53 × 162 mm
 (7 
1
/
4
 × 2 
1
/
8
 × 6 
1
/
2
 in.) (w/h/d)
– Continued on next page –
CDX-GT35U/
CXS-GT3516F
•  CXS-GT3516F is composed of CDX-GT35U,
  2 way speaker.
CDX-GT35U/CXS-GT3516F
2
Mass: Approx. 1.2 kg (2 lb. 11 oz.)
Supplied accessories:
  Card remote commander: RM-X151
  Parts for installation and connections (1 set)
16cm coaxial 2-way speaker
Speaker Coaxial 
2-way:
 
Woofer 16 cm, HOP,
 cone 
type
 
Tweeter 4 cm, Al,
 cone 
type
Peak power 
190 W
Rated power 
40 W
Impedance 4 
Ω
Sensitivity 90 
dB/W/m
Frequency response 
35 – 22,000 Hz
Mass 
Approx. 560 g per speaker
Supplied accessory 
Parts for installation
Design and specifi cations are subject to change
without notice.
SAFETY-RELATED  COMPONENT  WARNING!
COMPONENTS  IDENTIFIED  BY  MARK  
0  OR  DOTTED  LINE  
WITH  MARK  
0  ON  THE  SCHEMATIC  DIAGRAMS  AND  IN  
THE  PARTS  LIST  ARE  CRITICAL  TO  SAFE  OPERATION.
REPLACE  THESE  COMPONENTS  WITH  SONY  PARTS 
 
WHOSE  PART  NUMBERS  APPEAR  AS  SHOWN  IN  THIS  
MANUAL  OR  IN  SUPPLEMENTS  PUBLISHED  BY  SONY.
NOTES  ON  HANDLING  THE OPTICAL  PICK-UP 
 
BLOCK  OR  BASE  UNIT
The laser diode in the optical pick-up block may suffer electro-
static break-down because of the potential difference generated by 
the charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also 
use the procedure in the printed matter which is included in the 
repair parts.
The fl exible board is easily damaged and should be handled with 
care.
NOTES  ON  LASER  DIODE  EMISSION  CHECK
The laser beam on this model is concentrated so as to be focused 
on the disc refl ective surface by the objective lens in the optical 
pickup block. Therefore, when checking the laser diode emission, 
observe from more than 30 cm away from the objective lens.
NOTES  ON  CHIP  COMPONENT  REPLACEMENT
 •  Never reuse a disconnected chip component.
 •  Notice that the minus side of a tantalum capacitor may be 
damaged by heat.
ATTENTION  AU  COMPOSANT  AYANT  RAPPORT  
À  LA  SÉCURITÉ!
LES  COMPOSANTS  IDENTIFIÉS  PAR  UNE  MARQUE  
0  SUR  
LES  DIAGRAMMES  SCHÉMATIQUES  ET  LA  LISTE  DES  
PIÈCES  SONT  CRITIQUES  POUR  LA  SÉCURITÉ  DE  FONC-
TIONNEMENT.  NE  REMPLACER  CES  COMPOSANTS  QUE  
PAR  DES  PIÈCES  SONY  DONT  LES  NUMÉROS  SONT  DON-
NÉS  DANS  CE  MANUEL  OU  DANS  LES  SUPPLÉMENTS  
PUBLIÉS  PAR  SONY.
CDX-GT35U/CXS-GT3516F
3
1. 
SERVICE  NOTE
 ......................................................  
4
2. GENERAL
 Connections 
....................................................................  
5
3. DISASSEMBLY
3-1.   Sub Panel Assy  ...............................................................   7
3-2.   CD Mechanism Block .....................................................   7
3-3.   Main Board .....................................................................   8
3-4. Servo 
Board 
....................................................................   8
3-5.  Chassis (T) Sub Assy ......................................................   9
3-6. Roller 
Arm 
Assy 
..............................................................   9
3-7. Chassis 
(OP) 
Assy 
...........................................................  10
3-8. Chucking 
Arm 
Sub 
Assy 
.................................................  10
3-9. Sled 
Motor 
Assy 
..............................................................  11
3-10.  Optical Pick-up Section ..................................................   12
3-11. Optical Pick-up ...............................................................   12
4. DIAGRAMS
4-1.  Block Diagram –Main Section– .....................................   13
4-2.  Block Diagram –Display Section– .................................   14
4-3.  Printed Wiring Board –Main Section– ............................   16
4-4.  Schematic Diagram –Main Section (1/3)– ......................   17
4-5.  Schematic Diagram –Main Section (2/3)– ......................   18
4-6.  Schematic Diagram –Main Section (3/3)– ......................   19
4-7.  Printed Wiring Boards –Key Section– ............................   20
4-8.  Schematic Diagram –Key Section– ................................   21
5. EXPLODED 
VIEWS
5-1. Main 
Section 
...................................................................  26
5-2.  Front Panel Section .........................................................   27
5-3.  CD Mechanism Section (MG-101Y-188//Q) ..................   28
6. 
ELECTRICAL PARTS LIST
 ..................................   29
TABLE  OF  CONTENTS
TEST DISCS
Please use the following test discs for the check on the CD 
section.
 
YEDS-18 (Part No. 3-702-101-01)
 
PATD-012 (Part No. 4-225-203-01)
CAUTION
Use of controls or adjustments or performance of procedures 
other than those specifi ed herein may result in hazardous radia-
tion exposure.
If the optical pick-up block is defective, please replace the whole 
optical pick-up block.
Never turn the semi-fi xed resistor located at the side of optical 
pick-up block.
UNLEADED  SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution:  Some printed circuit boards may not come printed with 
the lead free mark due to their particular size)
 : LEAD  FREE  MARK
Unleaded solder has the following characteristics.
•  Unleaded solder melts at a temperature about 40 °C higher 
than ordinary solder.
 
Ordinary soldering irons can be used but the iron tip has to be 
applied to the solder joint for a slightly longer time.
 
Soldering irons using a temperature regulator should be set to 
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if 
the heated tip is applied for too long, so be careful!
• Strong 
viscosity
 
Unleaded solder is more viscous (sticky, less prone to fl ow) 
than ordinary solder so use caution not to let solder bridges 
occur such as on IC pins, etc.
• 
Usable with ordinary solder
 
It is best to use only unleaded solder but unleaded solder may 
also be added to ordinary solder.
optical pick-up
semi-fixed resistor
CDX-GT35U/CXS-GT3516F
4
SECTION  1
SERVICE  NOTE
EXTENSION  CABLE  AND  SERVICE  POSITION
When repairing or servicing this set, connect the jig (extension 
cable) as shown below.
•  Connect the MAIN board (CN701) and the SERVO board 
(CN401) with the extension cable (Part No. J-2502-076-1).
NOTE  FOR  REPLACEMENT  OF  THE  SERVO  BOARD
When repairing, the complete SERVO board (Part No. 
A-1555-002-A) should be replaced since any parts in the SERVO 
board cannot be repaired.
NOTE FOR REPLACEMENT OF THE USB CONNECTOR 
(CN902)
To replace the USB connector requires alignment.
1.  Insert the USB connector into the front panel.
2.  Place the KEY board on the front panel and align the terminals 
of the USB connector with the holes in the KEY board.
3.  Solder the four terminals of the connector.
NOTE  FOR  THE  20-PIN  CONNECTOR (CN901)
Do not use alcohol to clean the 20-pin connector (CN901) connect-
ing the front panel with the main body.
Do not touch the connector directly with your bare hand. Poor con-
tact may be caused.
SERVO BOARD 
CN401 
MAIN BOARD
CN701
J-2502-076-1 
KEY board
front panel 
USB (socket) connector
Page of 36
Display

Sony CDX-GT35U Service Manual ▷ Download

  • DOWNLOAD Sony CDX-GT35U Service Manual ↓ Size: 1.93 MB | Pages: 36 in PDF or view online for FREE
  • Here you can View online or download the Service Manual for the Sony CDX-GT35U in PDF for free, which will help you to disassemble, recover, fix and repair Sony CDX-GT35U Car Audio. Information contained in Sony CDX-GT35U Service Manual (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.