Sony CDX-GT31U Service Manual ▷ View online
SERVICE MANUAL
Sony Corporation
Audio&Video Business Group
Published by Sony Techno Create Corporation
CDX-GT31U
FM/MW/LW COMPACT DISC PLAYER
9-889-254-02
2008J04-1
©
2008.10
AEP Model
UK Model
Ver. 1.1 2008.10
SPECIFICATIONS
CD player section
Signal-to-noise ratio: 120 dB
Frequency response: 10 – 20,000 Hz
Wow and fl utter: Below measurable limit
Signal-to-noise ratio: 120 dB
Frequency response: 10 – 20,000 Hz
Wow and fl utter: Below measurable limit
Tuner section
FM
Tuning range: 87.5 – 108.0 MHz
Antenna (aerial) terminal:
External antenna (aerial) connector
Intermediate frequency: 10.7 MHz/450 kHz
Usable sensitivity: 9 dBf
Selectivity: 75 dB at 400 kHz
Signal-to-noise ratio:
67 dB (stereo), 69 dB (mono)
Harmonic distortion at 1 kHz:
0.5 % (stereo), 0.3 % (mono)
Separation: 35 dB at 1 kHz
Frequency response: 30 – 15,000 Hz
FM
Tuning range: 87.5 – 108.0 MHz
Antenna (aerial) terminal:
External antenna (aerial) connector
Intermediate frequency: 10.7 MHz/450 kHz
Usable sensitivity: 9 dBf
Selectivity: 75 dB at 400 kHz
Signal-to-noise ratio:
67 dB (stereo), 69 dB (mono)
Harmonic distortion at 1 kHz:
0.5 % (stereo), 0.3 % (mono)
Separation: 35 dB at 1 kHz
Frequency response: 30 – 15,000 Hz
MW/LW
Tuning range:
MW: 531 – 1,602 kHz
LW: 153 – 279 kHz
Antenna (aerial) terminal:
External antenna (aerial) connector
Intermediate frequency: 10.7 kHz/450 kHz
Sensitivity: MW: 30
Tuning range:
MW: 531 – 1,602 kHz
LW: 153 – 279 kHz
Antenna (aerial) terminal:
External antenna (aerial) connector
Intermediate frequency: 10.7 kHz/450 kHz
Sensitivity: MW: 30
μV, LW: 40μV
USB Player section
Interface: USB (Full-speed)
Maximum current: 500 mA
Interface: USB (Full-speed)
Maximum current: 500 mA
Power amplifi er section
Outputs: Speaker outputs (sure seal connectors)
Speaker impedance: 4 – 8 ohms
Maximum power output: 45 W
Outputs: Speaker outputs (sure seal connectors)
Speaker impedance: 4 – 8 ohms
Maximum power output: 45 W
× 4 (at 4 ohms)
General
Outputs:
Outputs:
Audio outputs terminal (sub/rear switchable)
Power antenna (aerial) relay control terminal
Power antenna (aerial) relay control terminal
Power
amplifi er control terminal
Inputs:
Telephone ATT control terminal
Antenna (aerial) input terminal
Antenna (aerial) input terminal
AUX input jack (stereo mini jack)
Model Name Using Similar Mechanism
CDX-GT420U/GT424U
CD Drive Mechanism Type
MG-101I-188//Q
Optical Pick-up Name
DAX-25A
• The tuner and CD sections have no adjustments.
Tone controls:
Low: ±10 dB at 60 Hz (XPLOD)
Mid: ±10 dB at 1 kHz (XPLOD)
High: ±10 dB at 10 kHz (XPLOD)
Power requirements: 12 V DC car battery
(negative ground (earth))
Dimensions: Approx. 178 × 50 × 179 mm
Dimensions: Approx. 178 × 50 × 179 mm
(7
1
/
8
× 2 × 7
1
/
8
in.) (w/h/d)
Mounting dimensions:
Approx. 182 × 53 × 162 mm
(7
1
/
4
× 2
1
/
8
× 6
1
/
2
in.) (w/h/d)
Mass: Approx. 1.2 kg (2 lb. 11 oz.)
Supplied accessories:
Parts for installation and connections (1 set)
Parts for installation and connections (1 set)
Design and specifi cations are subject to change
without notice.
CDX-GT31U
2
NOTES ON CHIP COMPONENT REPLACEMENT
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
TEST DISCS
Please use the following test discs for the check on the CD
section.
Please use the following test discs for the check on the CD
section.
YDES-18 (Part No. 3-702-101-01)
PATD-012 (Part No. 4-225-203-01)
SAFETY-RELATED COMPONET WARNING!
COMPONENTS IDENTIFIED BY MARK
0 OR DOTTED LINE
WITH MARK
0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
REPLACE THESE COMPONENTS WITH SONY PARTS
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostat-
ic break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The fl exible board is easily damaged and should be handled with
care.
ic break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The fl exible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused
on the disc refl ective surface by the objective lens in the optical
pickup block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
The laser beam on this model is concentrated so as to be focused
on the disc refl ective surface by the objective lens in the optical
pickup block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specifi ed herein may result in hazardous radia-
tion exposure.
Use of controls or adjustments or performance of procedures
other than those specifi ed herein may result in hazardous radia-
tion exposure.
If the optical pick-up block is defective, please replace the whole
optical pick-up block.
Never turn the semi-fi xed resistor located at the side of optical
pick-up block.
optical pick-up block.
Never turn the semi-fi xed resistor located at the side of optical
pick-up block.
optical pick-up
semi-fixed resistor
CDX-GT31U
3
Type of disc
Label on the disc
CD-DA
MP3
WMA
AAC
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong
viscosity
Unleaded solder is more viscous (sticky, less prone to fl ow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
•
Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
also be added to ordinary solder.
• CD Playback
You can play CD-DA (also containing CD TEXT) and CD-
R/CD-RW (MP3/WMA/AAC fi les).
R/CD-RW (MP3/WMA/AAC fi les).
This compact disc player is classifi ed as a CLASS 1 LASER
product. The CLASS 1 LASER PRODUCT label is located on the
exterior.
exterior.
This label is located on the bottom of the chassis.
1.
SERVICE NOTE
......................................................
4
2. GENERAL
Location of Controls ....................................................... 5
Connections
....................................................................
6
3. DISASSEMBLY
3-1. Sub Panel Assy ............................................................... 8
3-2. CD Mechanism Block ..................................................... 8
3-3. Main Board ..................................................................... 9
3-4. Servo
3-2. CD Mechanism Block ..................................................... 8
3-3. Main Board ..................................................................... 9
3-4. Servo
Board
.................................................................... 9
3-5. Chassis
(T)
Sub
Assy
...................................................... 10
3-6. Roller Arm Assy .............................................................. 10
3-7. Chassis
3-7. Chassis
(OP)
Assy
........................................................... 11
3-8. Chucking
Arm
Sub
Assy
................................................. 11
3-9. Sled
Motor
Assy
.............................................................. 12
3-10. Optical Pick-up Section .................................................. 13
3-11. Optical Pick-up ............................................................... 13
3-11. Optical Pick-up ............................................................... 13
4. DIAGNOSIS
FUNCTION
....................................... 14
5. DIAGRAMS
5-1. Block Diagram –Main Section– ..................................... 17
5-2. Block Diagram –Display Section– ................................. 18
5-3. Printed Wiring Board –Main Section– ............................ 20
5-4. Schematic Diagram –Main Section (1/3)– ...................... 21
5-5. Schematic Diagram –Main Section (2/3)– ...................... 22
5-6. Schematic Diagram –Main Section (3/3)– ...................... 23
5-7. Printed Wiring Boards –Key Section– ............................ 24
5-8. Schematic Diagram –Key Section– ................................ 25
5-2. Block Diagram –Display Section– ................................. 18
5-3. Printed Wiring Board –Main Section– ............................ 20
5-4. Schematic Diagram –Main Section (1/3)– ...................... 21
5-5. Schematic Diagram –Main Section (2/3)– ...................... 22
5-6. Schematic Diagram –Main Section (3/3)– ...................... 23
5-7. Printed Wiring Boards –Key Section– ............................ 24
5-8. Schematic Diagram –Key Section– ................................ 25
6. EXPLODED
VIEWS
6-1. Main
Section
................................................................... 30
6-2. Front Panel Section ......................................................... 31
6-3. CD Mechanism Section (MG-101I-188//Q) ................... 32
6-3. CD Mechanism Section (MG-101I-188//Q) ................... 32
7.
ELECTRICAL PARTS LIST
.................................. 33
TABLE OF CONTENTS
CDX-GT31U
4
SECTION 1
SERVICE NOTE
EXTENSION CABLE AND SERVICE POSITION
When repairing or servicing this set, connect the jig (extension
cable) as shown below.
When repairing or servicing this set, connect the jig (extension
cable) as shown below.
• Connect the MAIN board (CN350) and the SERVO board
(CN401) with the extension cable (Part No. J-2502-076-1).
NOTE FOR REPLACEMENT OF THE SERVO BOARD
When repairing, the complete SERVO board (Part No.
A-1362-921-A) should be replaced since any parts in the SERVO
board cannot be repaired.
When repairing, the complete SERVO board (Part No.
A-1362-921-A) should be replaced since any parts in the SERVO
board cannot be repaired.
NOTE FOR REPLACEMENT OF THE USB CONNECTOR
(CN902)
To replace the USB connector requires alignment.
1. Insert the USB connector into the front panel.
2. Place the KEY board on the front panel and align the terminals
(CN902)
To replace the USB connector requires alignment.
1. Insert the USB connector into the front panel.
2. Place the KEY board on the front panel and align the terminals
of the USB connector with the holes in the KEY board.
3. Solder the four terminals of the connector.
SERVO BOARD
CN401
CN401
MAIN BOARD
CN350
CN350
J-2502-076-1
KEY board
front panel
USB (socket) connector