Sony CDX-CA600 / CDX-CA600X Service Manual ▷ View online
1
Ver 1.1 2002. 04
Model Name Using Similar Mechanism
CDX-CA900/CA900X
CD Drive Mechanism Type
MG-393XA-121//Q
Optical Pick-up Name
KSS-720A
SERVICE MANUAL
AEP Model
UK Model
CDX-CA600/CA600X
E Model
CDX-CA600X
CDX-CA600/CA600X
FM/MW/LW COMPACT DISC PLAYER
CD player section
Signal-to-noise ratio
90 dB
Frequency response
10 – 20,000 Hz
Wow and flutter
Below measurable limit
Tuner section
FM
Tuning range
87.5 – 108.0 MHz
Aerial terminal
External aerial connector
Intermediate frequency 10.7 MHz/450 kHz
Usable sensitivity
Usable sensitivity
8 dBf
Selectivity
75 dB at 400 kHz
Signal-to-noise ratio
66 dB (stereo),
72 dB (mono)
72 dB (mono)
Harmonic distortion at 1 kHz
0.6% (stereo),
0.3% (mono)
0.3% (mono)
Separation
35 dB at 1 kHz
Frequency response
30 – 15,000 Hz
MW/LW
Tuning range
MW : 531 – 1,602 kHz
LW : 153 – 279 kHz
LW : 153 – 279 kHz
Aerial terminal
External aerial connector
Intermediate frequency 10.7 MHz/450 kHz
Sensitivity
Sensitivity
MW : 30 µV
LW : 40 µV
LW : 40 µV
SPECIFICATIONS
Power amplifier section
Outputs
Speaker outputs
(sure seal connectors)
(sure seal connectors)
Speaker impedance
4 – 8 ohms
Maximum power output 50 W
×
4 (at 4 ohms)
General
Outputs
Power aerial relay control lead
Input
Telephone ATT control lead
Tone controls
Bass ±9 dB at 100 Hz
Treble ±9 dB at 10 kHz
Treble ±9 dB at 10 kHz
Power requirements
12 V DC car battery
(negative earth)
(negative earth)
Dimensions
Approx. 178
×
50
×
177 mm
(w/h/d)
Mounting dimensions
Approx. 182
×
53
×
161 mm
(w/h/d)
Mass
Approx. 1.2 kg
Supplied accessories
Parts for installation and connections (1 set)
Front panel case (1)
Card remote commander RM-X115 (E model)
Front panel case (1)
Card remote commander RM-X115 (E model)
Note
This unit cannot be connected to a digital preamplifier or an equalizer.
Design and specifications are subject to change without
notice.
notice.
Photo: CDX-CA600X
• The tuner and CD sections have no adjustments.
Sony Corporation
e Vehicle Company
Published by Sony Engineering Corporation
9-873-434-02
2002D0400-1
© 2002. 04
2
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
OR BASE UNIT
OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
breakdown because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also use
the procedure in the printed matter which is included in the repair
parts.
The flexible board is easily damaged and should be handled with
care.
breakdown because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also use
the procedure in the printed matter which is included in the repair
parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission, ob-
serve from more than 30 cm away from the objective lens.
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission, ob-
serve from more than 30 cm away from the objective lens.
Notes on Chip Component Replacement
•
Never reuse a disconnected chip component.
•
Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
aged by heat.
•
CDX-CA600/CA600X: AEP, UK model
This label is located on the bottom of the chassis.
This label is located on the drive unit’s internal chassis.
CDX-CA600/CA600X
optical pick-up block
semi-fixed resistor
SERVICE NOTES
If the optical pick-up block is defective, please replace the whole
optical pick-up block.
Never turn the semi-fixed resistor located at the side of optical
pick-up block.
optical pick-up block.
Never turn the semi-fixed resistor located at the side of optical
pick-up block.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
other than those specified herein may result in hazardous
radiation exposure.
TEST DISCS
This set can playback CD-R and CD-ROM discs. The following
test discs should be used to check the capability:
test discs should be used to check the capability:
CD-R test disc TCD-R082LMT (Part No. J-2502-063-1)
CD-RW test disc TCD-W082L (Part No. J-2502-063-2)
CD-RW test disc TCD-W082L (Part No. J-2502-063-2)
NOTES ON CD-R/CD-RW DISCS
•
You can play CD-Rs (recordable CDs)/CD-RWs (rewritable CDs)
designed for audio use on this unit.
Look for these marks to distinguish CD-Rs/CD-RWs for audio
use.
designed for audio use on this unit.
Look for these marks to distinguish CD-Rs/CD-RWs for audio
use.
These marks denote that a disc is not for audio use.
•
Some CD-Rs/CD-RWs (depending on the equipment used for
its recording or the condition of the disc) may not play on this
unit.
its recording or the condition of the disc) may not play on this
unit.
•
You cannot play a CD-R/CD-RW that is not finalized
∗
.
∗
A process necessary for a recorded CD-R/CD-RW disc to be
played on the audio CD player.
played on the audio CD player.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
0
OR DOTTED LINE
WITH MARK
0
ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
3
TABLE OF CONTENTS
1. GENERAL
Location of controls
(CDX-CA600/CA600X: AEP, UK model) .............................. 4
Location of controls (CDX-CA600X: E model) ..................... 4
Connections (CDX-CA600/CA600X: AEP, UK model) ......... 5
Connections (CDX-CA600X: E model) .................................. 6
(CDX-CA600/CA600X: AEP, UK model) .............................. 4
Location of controls (CDX-CA600X: E model) ..................... 4
Connections (CDX-CA600/CA600X: AEP, UK model) ......... 5
Connections (CDX-CA600X: E model) .................................. 6
2. DISASSEMBLY
2-1. Panel (1) Assy, Sub ............................................................. 7
2-2. CD Mechanism Block ......................................................... 8
2-3. Main Board ......................................................................... 8
2-4. Heat Sink ............................................................................. 9
2-5. Chassis (T) Sub Assy .......................................................... 9
2-6. Lever Section .................................................................... 10
2-7. Servo Board ....................................................................... 10
2-8. Shaft Roller Assy .............................................................. 11
2-9. Floating Block Assy .......................................................... 11
2-10. Optical Pick-up Block ....................................................... 12
2-2. CD Mechanism Block ......................................................... 8
2-3. Main Board ......................................................................... 8
2-4. Heat Sink ............................................................................. 9
2-5. Chassis (T) Sub Assy .......................................................... 9
2-6. Lever Section .................................................................... 10
2-7. Servo Board ....................................................................... 10
2-8. Shaft Roller Assy .............................................................. 11
2-9. Floating Block Assy .......................................................... 11
2-10. Optical Pick-up Block ....................................................... 12
MAIN BOARD CNP701
SERVO BOARD CN1
3. DIAGRAMS
3-1. IC Pin Description ............................................................. 13
3-2. Block Diagram –CD Section– ........................................... 15
3-3. Block Diagram –Tuner Section– ....................................... 16
3-4. Block Diagram –Display Section– .................................... 17
3-5. Circuit Boards Location .................................................... 17
3-6. Printed Wiring Boards –CD Mechanism Section– ............ 18
3-7. Schematic Diagram –CD Mechanism Section– ................ 20
3-8. Printed Wiring Board –Main Section– .............................. 21
3-9. Schematic Diagram –Main Section (1/2)– ........................ 22
3-10. Schematic Diagram –Main Section (2/2)– ........................ 23
3-11. Printed Wiring Board –Display Section– .......................... 24
3-12. Schematic Diagram –Display Section– ............................. 25
3-2. Block Diagram –CD Section– ........................................... 15
3-3. Block Diagram –Tuner Section– ....................................... 16
3-4. Block Diagram –Display Section– .................................... 17
3-5. Circuit Boards Location .................................................... 17
3-6. Printed Wiring Boards –CD Mechanism Section– ............ 18
3-7. Schematic Diagram –CD Mechanism Section– ................ 20
3-8. Printed Wiring Board –Main Section– .............................. 21
3-9. Schematic Diagram –Main Section (1/2)– ........................ 22
3-10. Schematic Diagram –Main Section (2/2)– ........................ 23
3-11. Printed Wiring Board –Display Section– .......................... 24
3-12. Schematic Diagram –Display Section– ............................. 25
4. EXPLODED VIEWS
4-1. Chassis Section ................................................................. 28
4-2. Front panel Section ........................................................... 29
4-3. CD Mechanism Section (1) ............................................... 30
4-4. CD Mechanism Section (2) ............................................... 31
4-5. CD Mechanism Section (3) ............................................... 32
4-2. Front panel Section ........................................................... 29
4-3. CD Mechanism Section (1) ............................................... 30
4-4. CD Mechanism Section (2) ............................................... 31
4-5. CD Mechanism Section (3) ............................................... 32
5. ELECTRICAL PARTS LIST
........................................ 33
CDX-CA600/CA600X
EXTENSION CABLE AND SERVICE POSITION
When repairing or servicing this set, connect the jig (extension cable)
as shown below.
as shown below.
• Connect the MAIN board (CNP701) and the SERVO board (CN1)
with the extension cable (Part No. J-2502-062-1).
4
CDX-CA600/CA600X
SECTION 1
GENERAL
This section is extracted
from instruction manual.
from instruction manual.
(CDX-CA600/CA600X: AEP, UK model)
(CDX-CA600X: E model)
(CDX-CA600/CA600X: AEP, UK model)
(CDX-CA600X: E model)