Sony CDX-C560RDS Service Manual ▷ View online
– 17 –
2-9. SERVO BOARD
2
arm (roller)
3
roller assy
4
PS 2x3
5
LOAD SW board
Fig. 1
1
tension spring (RA)
washer
washer
arm
washers
4
loading motor assy
3
P 2x3
1
CN3
5
PS 2x4
6
PS 2x4
2-10. ROLLER ASSY
• When installing, take note of the positions
arm (roller) and washers. (Fig. 1)
arm (roller) and washers. (Fig. 1)
7
SERVO board
2
CN2
arm
– 18 –
2-11. CHASSIS (OP) (O/S) ASSY
2-12. OPTICAL PICK-UP BLOCK
8
compression spring (FL)
1
tension spring (angle)
6
chassis (OP) (O/S) assy
3
optical pick-up block
1
P 2x3
2
sled motor assy
7
compression spring (FL)
4
Fit lever (D) in the
direction of the arrow.
direction of the arrow.
3
damper (T)
5
Turn loading ring in the
direction of the arrow.
direction of the arrow.
2
damper (T)
– 19 –
SECTION 3
ELECTRICAL ADJUSTMENTS
TEST MODE
This set have the test mode function. In the test mode, FM Auto Scan/
Stop Level and MW Auto Scan/Stop Level adjustments can be
performed easier than it in ordinary procedure.
Stop Level and MW Auto Scan/Stop Level adjustments can be
performed easier than it in ordinary procedure.
<Set the Test Mode>
1. Set the “OFF” mode.
2. Push the preset 4 button.
3. Push the preset 5 button.
4. Press the preset 1 button for more than two seconds.
5. Then the display indicates all lights, the test mode is set.
1. Set the “OFF” mode.
2. Push the preset 4 button.
3. Push the preset 5 button.
4. Press the preset 1 button for more than two seconds.
5. Then the display indicates all lights, the test mode is set.
<Release the Test Mode>
1. Push the OFF button.
1. Push the OFF button.
TUNER SECTION
Cautions during repair
When the tuner unit is defective, replace it by a new one because
its internal block is difficult to repair.
its internal block is difficult to repair.
Note on Adjustment
The adjustments of tuner section, should be performed according to
the following sequence.
1. FM Auto Scan/Stop Level Adjustment
2. FM Stereo Separation Adjustment
3. FM RDS S-Meter Adjustment
4. MW Auto Scan/Stop Level Adjustment
the following sequence.
1. FM Auto Scan/Stop Level Adjustment
2. FM Stereo Separation Adjustment
3. FM RDS S-Meter Adjustment
4. MW Auto Scan/Stop Level Adjustment
0 dB = 1 µV
FM RF signal
generator
0.01 µF
antenna
terminal
terminal
set
Carrier frequency : 98.00 MHz
Output level
Output level
: 22 dB (12.6 µV)
Mode
: mono
Modulation
: 1 kHz, 22.5 kHz deviation (30%)
Procedure :
1. Set to the test mode.
2. Push the SOURCE button and set to FM.
1. Set to the test mode.
2. Push the SOURCE button and set to FM.
Display
FM Auto Scan/Stop Level Adjustment
Setting :
D-BASS switch : OFF
SOURCE button : FM
SOURCE button : FM
3. Push the preset 3 button.
Display
REG
SHUF1
4. Adjust with the volume RV2 on TU1 so that the “FM” indication
turns to “FM0” indication on the display window.
But, in case of already indicated “FM0”, turn the RV2 so that put
out light “0” indication and adjustment.
But, in case of already indicated “FM0”, turn the RV2 so that put
out light “0” indication and adjustment.
Display
Adjustment Location : See page 21.
REG
SHUF1
REG
SHUF1
– 20 –
FM Stereo Separation Adjustment
Setting :
D-BASS switch : OFF
SOURCE button : FM
SOURCE button : FM
FM RF signal
generator
Carrier frequency : 98.00 MHz
Output level
Output level
: 70 dB (3.2 mV)
Mode
: stereo
Modulation
: main : 1 kHz, 20 kHz deviation (26.5%)
sub : 1 kHz, 20 kHz deviation (26.5%)
19 kHz pilot : 7.5 kHz deviation (10%)
19 kHz pilot : 7.5 kHz deviation (10%)
antenna
terminal
terminal
set
0.01 µF
10 k
Ω
level meter
LINE OUT REAR
FM stereo
Level meter
Level meter
signal generator
connection
reading (dB)
output channel
L-CH
L-CH
A
B
R-CH
L-CH
Adjust RV3 on TU1 for
minimum reading.
minimum reading.
R-CH
R-CH
C
D
L-CH
R-CH
Adjust RV3 on TU1 for
minimum reading.
minimum reading.
L-CH stereo separation : A – B
R-CH stereo separation : C – D
The separations of both channels should be equal.
R-CH stereo separation : C – D
The separations of both channels should be equal.
Specification : Separation more than 28 dB
Adjustment Location : See page 21.
Procedure :
FM RF signal
generator
0.01 µF
antenna
terminal
terminal
set
Carrier frequency : 98.00 MHz
Output level
Output level
: 35 dB (56.2 µV)
Mode
: mono
Modulation
: no modulation
Procedure :
1. Set to the test mode. (See page 19.)
2. Push the SOURCE button and set to FM.
1. Set to the test mode. (See page 19.)
2. Push the SOURCE button and set to FM.
Display
FM RDS S-Meter Adjustment
Setting :
D-BASS switch : OFF
SOURCE button : FM
SOURCE button : FM
3. Push the preset 10 button.
4. Adjust VR601 so that the display indication is “16.0”.
4. Adjust VR601 so that the display indication is “16.0”.
Display
REG
SHUF1
REG
SHUF1
Specification : Display indication : 15.8 to 16.2.
Adjustment Location : See page 21.
Click on the first or last page to see other CDX-C560RDS service manuals if exist.