Sony CDX-605 (serv.man2) Service Manual ▷ View online
– 5 –
ADJUSTING PHASE OF SLIDERS (L, R)
1
Sliding the sliders (L, R) in the arrow direction, meet holes
a
and
b
of the sliders (L, R) with holes
c
and
d
of the case
(LOWER) ass’y.
a
b
c
d
slider (R)
slider (L)
case (LOWER) ass’y
GEAR (ELV2) / (ELV3)
1
gear (ELV 3)
Note: After mounting the gear, confirm
that the holes for phase adjustment
are not shifted.
are not shifted.
2
retaining ring
3
gear (ELV 2)
4
retaining ring
5
tension spring
(STOP LEVER)
– 6 –
2. MECHANICAL ADJUSTMENTS
Elevator Height (Address) Adjustment
Elevator Height (Address) Adjustment
Note: This adjustments is necessary when the system controller
(IC302), variable resistor (RV301), slider (R), slider (L), or
chassis (ELV) was replaced for any repair.
chassis (ELV) was replaced for any repair.
Connection:
power supply
master unit
+
GND
BUS cable
CDX-605
Adjustment Method:
1. Connect this set to the master unit (e.g. MDX-C670/C670RDS),
load a disc magazine, and place the set vertically as shown be-
low.
low.
2. Connect the regulated power supply to the master unit, and turn
the power on.
3. Press the DISC button on the master unit and select DISC 5.
4. At this time, if the elevator shaft does not position between comb
teeth A and B at addresses 5 and 6 as shown below, adjust the
following.
following.
5. Press repeatedly the DISC + and – buttons on the master unit so
that the elevator shafts moves from address 6 to address 5, or
from 5 to 6. At this time, adjust RV301 on the main board so that
the elevator shaft positions smoothly between comb teeth A and
B.
from 5 to 6. At this time, adjust RV301 on the main board so that
the elevator shaft positions smoothly between comb teeth A and
B.
6. Further, place the set horizontally and make same adjustment as
mentioned above.
7. After adjustment at addresses 5 to 6 is finished, check all opera-
tions from addresses 1 to 10 with the set placed vertically and
horizontally respectively to confirm that the elevator shaft posi-
tions in a range between comb teeth A to B.
horizontally respectively to confirm that the elevator shaft posi-
tions in a range between comb teeth A to B.
comb tooth at address 6
elevator shaft
comb tooth at address 6
comb tooth at address 5
comb tooth at adress 5
elevator shaft
A
A
B
B
OK
NG
RV301
– 7 –
3. BOARD MODIFICATION
3-1. NEW/FORMER DISCRIMINATION
[RF BOARD] – Conductor Side –
[JACK BOARD] – Conductor Side –
[MAIN BOARD] – Component Side –
Former : 1-664-629-11
New
New
: 1-664-629-12
Former : 1-664-631-11
New
New
: 1-664-631-12, -13
Former : 1-664-630-11
New
New
: 1-664-630-12, -13
– 21 –
3-6. ELECTRICAL PARTS LIST
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Description
Remark
NOTE:
•
Due to standardization, replacements in the
parts list may be different from the parts speci-
fied in the diagrams or the components used on
the set.
parts list may be different from the parts speci-
fied in the diagrams or the components used on
the set.
•
-XX and -X mean standardized parts, so they
may have some difference from the original one.
may have some difference from the original one.
•
RESISTORS
All resistors are in ohms.
METAL: Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F: nonflammable
All resistors are in ohms.
METAL: Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F: nonflammable
•
Items marked “*” are not stocked since they
are seldom required for routine service.
Some delay should be anticipated when order-
ing these items.
are seldom required for routine service.
Some delay should be anticipated when order-
ing these items.
•
SEMICONDUCTORS
In each case, u: µ, for example:
uA. . : µA. .
In each case, u: µ, for example:
uA. . : µA. .
uPA. . : µPA. .
uPB. . : µPB. .
uPC. . : µPC. .
uPD. . : µPD. .
•
CAPACITORS
uF: µF
uF: µF
•
COILS
uH: µH
uH: µH
MAIN
JACK
*
1-664-631-13 JACK BOARD
**********
< CAPACITOR >
C901
1-163-009-11 CERAMIC CHIP
0.001uF 10%
50V
C902
1-163-038-00 CERAMIC CHIP
0.1uF
25V
C903
1-163-038-00 CERAMIC CHIP
0.1uF
25V
C905
1-162-302-11 CERAMIC
0.0022uF 30%
16V
< CONNECTOR >
CN901
1-779-077-21 PLUG, CONNECTOR (SONY BUS/AUDIO OUT)
CNJ901 1-778-775-21 CONNECTOR, FPC 13P
< FERRITE BEAD >
FB901
1-500-445-21 INDUCTOR 0uH
FB902
1-500-445-21 INDUCTOR 0uH
FB903
1-500-445-21 INDUCTOR 0uH
< IC LINK >
IC901
1-532-686-21 LINK, IC
************************************************************
*
A-3313-220-A MAIN BOARD, COMPLETE
********************
*
3-012-099-01 HOLDER (TR2)
< CAPACITOR >
C101
1-163-038-00 CERAMIC CHIP
0.1uF
25V
C102
1-163-251-11 CERAMIC CHIP
100PF
5%
50V
C103
1-163-011-11 CERAMIC CHIP
0.0015uF 10%
50V
C104
1-163-809-11 CERAMIC CHIP
0.047uF 10%
25V
C105
1-164-004-11 CERAMIC CHIP
0.1uF
10%
25V
C106
1-164-182-11 CERAMIC CHIP
0.0033uF 10%
50V
C107
1-164-232-11 CERAMIC CHIP
0.01uF
50V
C108
1-163-038-00 CERAMIC CHIP
0.1uF
25V
C109
1-126-513-11 ELECT
47uF
20%
6.3V
C110
1-163-038-00 CERAMIC CHIP
0.1uF
25V
C111
1-163-038-00 CERAMIC CHIP
0.1uF
25V
C120
1-163-038-00 CERAMIC CHIP
0.1uF
25V
C121
1-163-038-00 CERAMIC CHIP
0.1uF
25V
C122
1-163-038-00 CERAMIC CHIP
0.1uF
25V
C123
1-163-038-00 CERAMIC CHIP
0.1uF
25V
C124
1-163-038-00 CERAMIC CHIP
0.1uF
25V
C125
1-163-009-11 CERAMIC CHIP
0.001uF 10%
50V
C201
1-124-589-11 ELECT
47uF
20%
16V
C202
1-126-513-11 ELECT
47uF
20%
6.3V
C203
1-163-038-00 CERAMIC CHIP
0.1uF
25V
C204
1-115-466-00 ELECT
1000uF 20%
16V
C205
1-163-038-00 CERAMIC CHIP
0.1uF
25V
C206
1-124-589-11 ELECT
47uF
20%
16V
C207
1-124-589-11 ELECT
47uF
20%
16V
C208
1-164-346-11 CERAMIC CHIP
1uF
16V
C209
1-124-589-11 ELECT
47uF
20%
16V
C210
1-125-701-11 CAPACITOR
0.047F
5.5V
C211
1-163-038-00 CERAMIC CHIP
0.1uF
25V
C212
1-164-346-11 CERAMIC CHIP
1uF
16V
C213
1-164-346-11 CERAMIC CHIP
1uF
16V
C214
1-163-038-00 CERAMIC CHIP
0.1uF
25V
C302
1-163-038-00 CERAMIC CHIP
0.1uF
25V
C303
1-126-513-11 ELECT
47uF
20%
6.3V
C304
1-163-038-00 CERAMIC CHIP
0.1uF
25V
C305
1-163-038-00 CERAMIC CHIP
0.1uF
25V
C306
1-163-038-00 CERAMIC CHIP
0.1uF
25V
C308
1-163-038-00 CERAMIC CHIP
0.1uF
25V
C401
1-124-589-11 ELECT
47uF
20%
16V
C402
1-163-038-00 CERAMIC CHIP
0.1uF
25V
C403
1-163-038-00 CERAMIC CHIP
0.1uF
25V
C404
1-126-513-11 ELECT
47uF
20%
6.3V
C405
1-126-513-11 ELECT
47uF
20%
6.3V
C406
1-163-038-00 CERAMIC CHIP
0.1uF
25V
C407
1-126-157-11 ELECT
10uF
20%
16V
C408
1-163-038-00 CERAMIC CHIP
0.1uF
25V
C409
1-126-513-11 ELECT
47uF
20%
6.3V
C410
1-126-157-11 ELECT
10uF
20%
16V
C411
1-126-157-11 ELECT
10uF
20%
16V
C412
1-163-263-11 CERAMIC CHIP
330PF
5%
50V
C413
1-163-251-11 CERAMIC CHIP
100PF
5%
50V
When indicating parts by reference
number, please include the board.
number, please include the board.
Click on the first or last page to see other CDX-605 (serv.man2) service manuals if exist.