Sony CDX-601 / CDX-636 Service Manual ▷ View online
5
SECTION 3
DISASSEMBLY
COVER (UPPER T), FRONT PANEL ASS’Y
Note:
Follow the disassembly procedure in the numerical order given.
1
screw
(PTT2.6
(PTT2.6
×
6)
3
lever (FLT)
1
screw (PTT2.6
×
6)
1
screw (PTT2.6
×
6)
1
screw (PTT2.6
×
6)
1
screw
(PTT2.6
(PTT2.6
×
6)
4
front panel ass’y
3
lever (FLT)
2
cover (upper T)
MECHANISM DECK (MG-251A-137)
2
tension coil spring (FL)
2
tension coil spring (FL)
1
two dampers (250T)
filament tape
1
two dampers (250T)
3
jack flexible board
(CNJ901)
(CNJ901)
4
mechanism deck (MG-251A-137)
6
JACK BOARD
Remove the jack board of
the arrow.
the arrow.
1
ground point screw
(PTT2.6
(PTT2.6
×
6)
2
jack board
MAIN BOARD, SLIDE VARIABLE RESISTOR (ELEVATOR HEIGHT SENSOR) (RV202)
2
Remove two solders of
the elevator motor leads (M104).
the elevator motor leads (M104).
2
Remove two solders of
the switch board leads.
the switch board leads.
2
Remove three solders of
the slide variable resistor
(RV202).
the slide variable resistor
(RV202).
4
heat sink (T)
3
screw (PTT2
×
4)
6
main board
5
two screws (FP)
1
main flexible board
(CNJ101)
(CNJ101)
5
screw (FP)
7
screw
(PTT2
(PTT2
×
4)
8
slide variable resistor
(elevator height sensor)
(RV202)
(elevator height sensor)
(RV202)
7
ELJ MOTOR ASS’Y (ELEVATOR) (M104)
ESCUTCHEON (T)
1
screw
(PTT2
(PTT2
×
4)
2
bracket (EVM.S)
3
ELJ motor ass’y (elevator)
(M104)
(M104)
2
Remove the claw
in the direction of the arrow A.
in the direction of the arrow A.
4
Remove the ditch
in the direction of the arrow B.
in the direction of the arrow B.
A
B
5
Remove the escutcheon (T)
in the direction of the arrow C.
in the direction of the arrow C.
4
ditch
3
claw
C
3
two claws
1
screw (T)
8
CHASSIS (U.S) SUB ASS’Y
CHASSIS ASS’Y
1
three screws
(PTT2
(PTT2
×
4)
1
screw
(PTT2
(PTT2
×
4)
1
two screws
(PTT2
(PTT2
×
4)
5
spring (SUT)
3
Remove the edge
in the direction
of the arrow A.
in the direction
of the arrow A.
4
Remove the chassis (U.S)
sub ass’y in the direction
of the arrow B.
sub ass’y in the direction
of the arrow B.
2
B
A
4
Remove the chassis ass’y
in the direction of the arrow B.
in the direction of the arrow B.
1
Turn the gear (EVD.S) fully
in the direction of the arrow A.
in the direction of the arrow A.
5
spring (stopper.lower)
B
A
3
2
3
Click on the first or last page to see other CDX-601 / CDX-636 service manuals if exist.