Sony CDX-600 / CDX-606 / CDX-626 Service Manual ▷ View online
– 33 –
IC204
BA8272F-E2
IC401
TC9464FN-EL
IC301
BA6287F
1
2
3
4
5
6
7
8
9
10
14
13
12
11
VCC
BUS ON
LINK OFF
CLK OUT
DATA OUT
DATA IN
BUS RESET
BUS DATA
VREF
BUS CLK
GND
BUS ON IN
BUS ON OUT
RESET
RESET
SWITCH
1
2
3
4
OUT1
VM
VCC
FIN
8
7
6
5
GND
OUT2
VREF
RIN
CONTROL LOGIC
TSD
POWER
SAVE
DRIVER
DRIVER
DIGITAL FILTER CIRCUIT
ATTENUATOR OPERATIONAL CIRCUIT
DEEMPHASIS FILTER CIRCUIT
D-
∆
MODULATION CIRCUIT
INTERFACE
CIRCUIT
TEST
CIRCUIT
OUTPUT
CIRCUIT
CIRCUIT
ANALOG
FILTER
TIMING
GENERATOR
OSC
MICROCOMPUTER
INTERFACE
CIRCUIT
OUTPUT
CIRCUIT
CIRCUIT
ANALOG
FILTER
1
2
3 4
5
6
7
8
9
10
20
19
18
17
16
15
14 13
12
11
21
22
23
24
LRCK
BCK
DATA
HS
(SM)
ATT
(EMP)
SH
(BS)
LA
VDX
XO
XI
GNDX
MCK
VDD
T1
P/S
VDA
RO
GNDA
VR
GNDA
LO
GNDD
ZD
VDA
– 34 –
7-8.
IC PIN FUNCTION DESCRIPTION
•
MAIN BOARD IC302 CXP84124-080Q (SYSTEM CONTROLLER)
Pin No.
Pin Name
I/O
Function
1
LIM.SW
I
Sled limit in detect switch (SW1) input terminal
“L”: When the optical pick-up is inner position
“L”: When the optical pick-up is inner position
2
BUSON
I
Bus on/off control signal input from the SONY bus interface (IC204) “H”: bus on
3
EJECT
I
Eject switch (SW303) input terminal “H” active
4
LOAD1
I
Save end detect switch (SW12) input terminal
“L”: When completion of the disc chucking operation
“L”: When completion of the disc chucking operation
5
LOAD2
I
Chucking end detect switch (SW11) input terminal
“L”: When completion of the disc chucking operation
“L”: When completion of the disc chucking operation
6
A.MUTE
O
Audio line muting on/off control signal output terminal “H”: muting on
7
EMPH
O
Emphasis mode output to the D/A converter (IC401) “L”: emphasis on
8
CH.R
O
Motor drive signal (save direction) output to the chucking motor drive (IC52)
“H” active *1
“H” active *1
9
CH.F
O
Motor drive signal (load chucking direction) output to the chucking motor drive (IC52)
“H” active *1
“H” active *1
10
—
O
Not used (open)
11
ELV.R
O
Motor drive signal (elevator down direction) output to the elevator motor drive (IC301)
“L” active *2
“L” active *2
12
ELV.ON
O
Mechanism deck section power supply on/off control signal output “H”: power on
13
CD RST
O
System reset signal output to the CXA1992BR (IC11) and CXD2530Q (IC101) “L”: reset
14
CDON
O
D/A converter and servo section power supply on/off control signal output “H”: power on
15 to 23
—
O
Not used (open)
24
AUTO ON/OFF
I
Setting terminal for the automatic adjustment
“L”: automatic adjustment, “H”: manual adjustment (fixed at “L” in this set)
“L”: automatic adjustment, “H”: manual adjustment (fixed at “L” in this set)
25 to 29
—
O
Not used (open)
30
RESET
I
System reset signal input from the reset signal generator (IC202) and SONY bus interface (IC204)
“L”: reset
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
“L”: reset
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
31
EXTAL
I
Main system clock input terminal (8 MHz)
32
XTAL
O
Main system clock output terminal (8 MHz)
33
VSS
—
Ground terminal
34
TX
O
Sub system clock output terminal Not used (open)
35
TEX
I
Sub system clock input terminal Not used (fixed at “L”)
36
AVSS
—
Ground terminal (for A/D converter)
37
AVREF
I
Reference voltage (+5V) input terminal (for A/D converter)
38
ATRIBT
I
Selection input of the custom file, D-BASS, etc.
39
MCK
I
Input of signal for the fine adjustment (linear position sensor adjustment; RV301) of elevator
position (A/D input)
position (A/D input)
40
EHS
I
Elevator height position detect input from the RV302 (elevator height sensor) (A/D input)
41 to 47
—
O
Not used (open)
48
SCK
I
Serial data transfer clock signal input from the SONY bus interface (IC204)
49
SI
I
Serial data input from the SONY bus interface (IC204)
50
SO
O
Serial data output to the SONY bus interface (IC204)
51
SQCLK
O
Subcode Q data reading clock signal output to the CXD2530Q (IC101)
52
SUBQ
I
Subcode Q data input from the CXD2530Q (IC101)
53
—
O
Not used (open)
54
—
I
Not used (fixed at “H”)
55
MGLK
I
Magazine eject operation completion detect switch (SW301) input terminal
“L”: eject completed
“L”: eject completed
– 35 –
Pin No.
Pin Name
I/O
Function
56
SCOR
I
Subcode sync (S0+S1) detection signal input from the CXD2530Q (IC101)
57
SENS2
I
Internal status signal (sense signal) input from the CXA1992BR (IC11)
58
PWM
O
Motor drive signal (elevator up direction) output to the elevator motor drive (IC301)
“L” active *2
“L” active *2
59
—
O
Not used (open)
60
MAG.SW
I
Magazine in/out detect switch (SW302) input terminal “L”: magazine detected
61
BUCHECK
I
Battery detection signal input terminal “H”: battery on
62
W.UP
I
Bus on or eject switch (SW303) input terminal “H”: bus on or eject switch pushing
63
C.OUT
I
Track number count signal input from the CXA1992BR (IC11)
64
EEDATA
I/O
Two-way data bus with the EEPROM Not used (open)
65
EECLK
O
Serial clock signal output to the EEPROM Not used (open)
66
EEINIT
I
Initialize signal input for the EEPROM “H”: format Fixed at “L” in this set
67
—
O
Not used (open)
68
SINGLE
I
Setting terminal for the single disc/multiple discs mode
“L”: single mode, “H”: multiple discs mode (fixed at “H”)
“L”: single mode, “H”: multiple discs mode (fixed at “H”)
69
FOK
I
Focus OK signal input from the CXA1992BR (IC11) “L”: NG, “H”: OK
70
GFS
I
Guard frame sync signal input from the CXD2530Q (IC101) “L”: NG, “H”: OK
71
SENS1
I
Internal status signal (sense signal) input from the CXD2530Q (IC101)
72
VDD
—
Power supply terminal (+5V)
73
NC (VDD)
—
Connected to the power supply (+5V)
74
CDCLK
O
Serial data transfer clock signal output to the CXD2530Q (IC101)
75
CDXLT
O
Serial data latch pulse signal output to the CXD2530Q (IC101)
76
CDDATA
O
Serial data output to the CXD2530Q (IC101)
77 to 80
—
O
Not used (open)
*1 chucking motor (M103) control
STOP
LOAD
CHUCKING
SAVE
BRAKE
CH.F (pin 9)
“L”
“H”
“L”
“H”
CH.R (pin 8)
“L”
“L”
“H”
“H”
Mode
Terminal
*2 elevator motor (M104) control
STOP
ELEVATOR
UP
ELEVATOR
DOWN
BRAKE
PWM (pin %•)
“H”
“L”
“H”
“L”
ELV.R (pin !¡)
“H”
“H”
“L”
“L”
Mode
Terminal
– 36 –
(1)
COVER SECTION
SECTION 8
EXPLODED VIEWS
Les composants identifiés par une
marque
marque
! sont critiquens pour la
sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
Ne les remplacer que par une pièce
portant le numéro spécifié.
The components identified by
mark
mark
! or dotted line with mark
! are critical for safety.
Replace only with part number
specified.
specified.
• Items marked “*” are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering
these items.
delay should be anticipated when ordering
these items.
• The mechanical parts with no reference num-
ber in the exploded views are not supplied.
• Hardware (# mark) list and accessories and
packing materials are given in the last of the
electrical parts list.
electrical parts list.
NOTE:
• -XX and -X mean standardized parts, so they
may have some difference from the original
one.
one.
• Color Indication of Appearance Parts
Example:
KNOB, BALANCE (WHITE) . . . (RED)
KNOB, BALANCE (WHITE) . . . (RED)
↑
↑
Parts Color Cabinet's Color
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Description
Remark
1
3-010-104-01 DAMPER (250)
* 2
3-010-097-01 COVER (LOWER) (CDX-606/626)
* 2
3-010-097-21 COVER (LOWER T) (CDX-600)
3
1-664-628-11 JACK FLEXIBLE BOARD
* 4
1-672-620-11 JACK BOARD
5
X-3376-770-1 DOOR ASSY (CDX-606)
5
X-3376-771-1 DOOR (600T) ASSY (CDX-600)
5
X-3376-773-1 DOOR (626T) ASSY (CDX-626)
6
3-376-464-11 SCREW (+PTT 2.6X6), GROUND POINT
7
3-022-002-62 PANEL (T), FRONT (CDX-600)
7
3-022-002-72 PANEL (T), FRONT (CDX-626)
7
3-030-560-01 PANEL, FRONT (CDX-606)
8
3-012-388-01 SCREW (M2X3)
* 9
3-010-105-01 ESCUTCHEON (CDX-606)
* 9
3-022-006-01 ESCUTCHEON (T) (CDX-600/626)
* 10
3-010-106-01 BUTTON (EJ) (
6) (CDX-606)
* 10
3-022-007-01 BUTTON (EJT) (
6) (CDX-600/626)
* 11
3-022-012-01 HEAT SINK (T)
12
3-010-103-01 SPRING (FL), TENSION
13
3-010-101-01 LEVER (FL) (CDX-606/626)
13
3-010-101-11 LEVER (FLT) (CDX-600)
* 14
3-010-096-01 COVER (UPPER) (CDX-606/626)
* 14
3-010-096-21 COVER (UPPER T) (CDX-600)
* 15
A-3317-606-A MAIN BOARD, COMPLETE
* 16
3-022-694-01 HOLDER (TR3)
17
3-935-636-11 SCREW (FP)
18
X-3373-215-1 ARM (FL) ASSY (CDX-606)
18
X-3375-357-1 ARM (FLT) ASSY (CDX-600/626)
* 19
3-013-658-01 SHEET (FJT), PROTECTION
20
X-3373-986-1 ARM (FR) ASSY (CDX-606)
20
X-3375-360-1 ARM (FRT) ASSY (CDX-600/626)
* 21
3-024-065-01 CUSHION (EJECT) (CDX-600/626)
21
3-350-124-01 CUSHION (EJECT) (CDX-606)
22
3-024-067-01 CUSHION (T), BATTERY (CDX-600/626)
22
3-911-215-02 SHEET (LEAD RETAINER) (CDX-606)
23
3-028-802-01 SPACER (MOUNT 30)
IC201
8-759-054-12 IC PQ09RA1
IC203
8-759-324-40 IC KIA7805PI
5
7
13
14
13
12
15
23
16
8
10
9
11
12
6
4
3
19
1
21
19
2
1
20
18
17
#2
#2
#2
#3
#2
#2
#1
not supplied
MG-250C-137
IC203
IC201
22
main flexible board
Click on the first or last page to see other CDX-600 / CDX-606 / CDX-626 service manuals if exist.