DOWNLOAD Sony CDX-3180 Service Manual ↓ Size: 3.91 MB | Pages: 44 in PDF or view online for FREE

– 13 –

• When installing, take note of the positions
  arm (roller) and washers. (Fig. 1)

5

 PS 2x4

1

 CN3

3

 P 2x3

4

 loading motor assy

7

 SERVO board

2

 CN2

6

 PS 2x4

4

 PS 2x3

5

 LOAD SW board

1

 tension spring (RA)

2

 arm (roller)

3

 roller assy

washer

arm

arm

washer

washers

– 14 –

1

 P 2x3

2

 sled motor assy

3

 optical pick-up block

1

 tension spring (angle)

8

 compression spring (FL)

7

 chassis (OP) (O/S) assy

9

 compression spring (FL)

2

 tension spring (KR1)

5

 Fit lever (D) in the

     direction of the arrow.

3

 damper (T)

4

 damper (T)

6

 Turn loading ring in the

     direction of the arrow.

– 15 –

This set have the test mode function. In the test mode, FM Auto
Scan/Stop Level and MW Auto Scan/Stop Level adjustments can
be performed easier than it in ordinary procedure.

<Set the Test Mode>
1. Set the “OFF” mode.
2. Push the preset  4  button.
3. Push the preset  5  button.
4. Press the preset  1  button for more than two seconds.
5. Then the display indicates all lights, the test mode is set.

<Release the Test Mode>
1. Push the  OFF  button.

When the tuner unit is defective, replace it by a new one
because its internal block is difficult to repair.

The adjustments of tuner section, should be performed according
to the following sequence.
1. FM Auto Scan/Stop Level Adjustment
2. FM Stereo Separation Adjustment
3. MW Auto Scan/Stop Level Adjustment

µ

FM RF signal

generator

0.01 

µ

F

antenna
terminal

set

Carrier frequency : 98.00 MHz
Output level

: 22 dB (12.6 

µ

V)

Mode

: mono

Modulation

: 1 kHz, 22.5 kHz deviation (30%)

Procedure :
1. Set to the test mode.
2. Push the  SOURCE  button and set to FMI.

Display

D-BASS switch : OFF
SOURCE button : FMI

3. Push the preset  3  button.

Display

4. Adjust with the volume RV2 on TU1 so that the “FMI”

indication turns to “FMII” indication on the display window.
But, in case of already indicated “FMII”, turn the RV2 so that
put out light “I” indication and adjustment.

Display

Adjustment Location : See page 17.

– 16 –

D-BASS switch : OFF
SOURCE button : FMI

FM RF signal

generator

Carrier frequency : 98.00 MHz
Output level

: 70 dB (3.2 mV)

Mode

: stereo

Modulation

: main : 1 kHz, 20 kHz deviation (26.5%)

sub : 1 kHz, 20 kHz deviation (26.5%)
19 kHz pilot : 7.5 kHz deviation (10%)

antenna
terminal

set

0.01 

µ

F

10 k 

Ω

level meter

LINE OUT REAR

L-CH

L-CH

A

B

R-CH

L-CH

Adjust RV4 on TU1 for
minimum reading.

R-CH

R-CH

C

D

L-CH

R-CH

Adjust RV4 on TU1 for
minimum reading.

L-CH stereo separation : A – B
R-CH stereo separation : C – D
The separations of both channels should be equal.

Specification : Separation more than 28 dB

Adjustment Location : See page 17.

D-BASS switch

: OFF

SOURCE 

n MODE button : MW

AM RF signal

generator

Carrier frequency : 999 kHz
30% amplitude
modulation by
1 kHz signal
output level

: 33 dB (44.7 

µ

V)

AM dummy
antenna (50 

Ω

)

antenna
terminal

set

15 pF

30 

Ω

65 pF

Procedure :
1. Set to the test mode. (See page 15.)
2. Push the  SOURCE  button.
3. Push the  MODE  button and set to MW.

Display

4. Push the preset  3  button.

Display

5. Adjust with the volume RV1 on TU1 so that the “I”

indication on the display window.
But, in case of already indicated “I”, turn the RV1 so that put
out light “I” indication and adjustment.

Display

Adjustment Location : See page 17.