Sony ZS-Y2L Service Manual ▷ View online
9
ZS-Y2L
3-6. LCD BOARD
2
1
3
seven screws (B2.6)
4
CD window
6
three screws (B2.6)
7
two screws (B2.6)
8
panel CD sub assy
9
flexible flat cable (27core)
(CN401)
(CN401)
0
LCD board
5
CD ring
10
ZS-Y2L
SECTION 4
ELECTRICAL ADJUSTMENTS
TUNER SECTION
0 dB=1
µ
V
[MW/LW]
Setting:
Function: RADIO
RADIO, AUTO PRESET, BAND button: MW or LW
Function: RADIO
RADIO, AUTO PRESET, BAND button: MW or LW
[FM]
Setting:
Function: RADIO
RADIO, AUTO PRESET, BAND button: FM
Function: RADIO
RADIO, AUTO PRESET, BAND button: FM
• Repeat the procedures in each adjustment several times, and
the tracking adjustments should be finally done by the trimmer
capacitors.
capacitors.
• Remove FM antenna in FM adjustment.
AM RF signal
generator
30% amplitude
modulation by
400 Hz signal
Output level:
as low as possible
modulation by
400 Hz signal
Output level:
as low as possible
Put the lead-wire
antenna close to
the set.
antenna close to
the set.
+
–
–
level meter
set
32
Ω
i
jack (J321)
FM RF signal
generator
75 kHz frequency
deviation by 1 kHz
signal
Output level:
as low as possible
deviation by 1 kHz
signal
Output level:
as low as possible
+
–
–
level meter
0.01
µ
F
TU board
TP (GND)
TP (GND)
TU board
TP (ANT)
TP (ANT)
set
32
Ω
i
jack (J321)
digital voltmeter
TP (VT)
TP (GND)
100 k
Ω
TU board
AM IF ADJUSTMENT
Adjust for a maximum reading on level meter
T1
450 kHz
MW FREQUENCY COVERAGE CONFIRMATION
Frequency Display
Reading on Digital Voltmeter
531 kHz
1.0
± 0.5 V
1,611 kHz
5.2
± 0.6 V
MW TRACKING ADJUSTMENT
Adjust for a maximum reading on level meter
L3-1
621 kHz
CT3
1,404 kHz
LW FREQUENCY COVERAGE ADJUSTMENT
Adjustment Part
Frequency Display
Reading on Digital Voltmeter
Confirmation
153 kHz
0.6
± 0.3 V
L4
279 kHz
5.0
± 0.1 V
LW TRACKING ADJUSTMENT
Adjust for a maximum reading on level meter
L3-2
162 kHz
CT5
261 kHz
FM IF ADJUSTMENT
Adjust for a minimum reading on level meter
T2
10.7 MHz
FM FREQUENCY COVERAGE ADJUSTMENT
Adjustment Part
Frequency Display
Reading on Digital Voltmeter
L2
108 MHz
3.0
± 0.2 V
Confirmation
87.5 MHz
1.3
± 0.3 V
FM TRACKING ADJUSTMENT
Adjust for a maximum reading on level meter
L1
87.5 MHz
CT1
108 MHz
Adjustment and Connecting Location: TU board (See page 11)
11
ZS-Y2L
Adjustment and Connecting Location:
L4
LW Frequency Coverage Adjustment
L2
FM Frequency Coverage Adjustment
MW Tracking Adjustment
L3-1
CT3
LW Tracking Adjustment
CT5
L3-2
FM Tracking Adjustment
T1 AM IF Adjustment
T2 FM IF Adjustment
L1
CT1
CT1
TP
(VT)
TP
(GND)
TP
(ANT)
– TU Board (Component Side) –
– TU Board (Conductor Side) –
12
ZS-Y2L
CD SECTION
CD section adjustments are done automatically in this set.
In case of operation check, confirm that focus bias.
In case of operation check, confirm that focus bias.
Focus Bias Check
1. Connect a oscilloscope to TP (RF) and TP (GND) on the CD
board.
2. Insert the disc (YEDS-18). (Part No.: 3-702-101-01)
3. Press the
3. Press the
u
button.
4. Confirm that the oscilloscope waveform is as shown in the
figure below. (eye pattern)
A good eye pattern means that the diamond shape (
◊) in
thecenter of the waveform can be clearly distinguished.
RF Signal Reference Waveform (Eye Pattern)
Checking Location:
– CD BOARD (Conductor Side) –
VOLT/DIV: 0.2 V (with the 10: 1 probe in use.)
TIME/DIV: 500 ns
TIME/DIV: 500 ns
0.65 to 1.05 Vp-p
When observing the eye pattern, set the oscilloscope
for AC range and raise vertical sensitivity.
for AC range and raise vertical sensitivity.
IC701
TP (GND)
TP
(RF)
Click on the first or last page to see other ZS-Y2L service manuals if exist.