Sony ZS-X3CP Service Manual ▷ View online
ZS-X3CP
7
• This set can be disassembled in the order shown below.
3-1.
DISASSEMBLY FLOW
SECTION 3
DISASSEMBLY
3-2. CABINET LOWER,
TELESCOPIC ANTENNA (ANT1)
(Page 8)
(Page 8)
3-3. MAIN CHASSIS SECTION
(Page 9)
3-4. AUDIO BOARD,
BATTERY BOARD
(Page 9)
(Page 9)
3-5. TUNER BOARD,
CONTROL BOARD
(Page 10)
(Page 10)
3-6. CDMP3 BOARD
(Page 11)
3-7. OPTICAL PICK-UP
SECTION
(Page 11)
(Page 11)
3-8. SLED MOTOR ASSY
(780CP) (M702)
(Page 12)
(Page 12)
3-9. OPTICAL PICK-UP
(KSS-900A)
(Page 12)
(Page 12)
3-10.CABINET FRONT SECTION
(Page 13)
3-11.SPEAKER (10cm) (L) (SP1),
SPEAKER (10cm) R) (SP2)
(Page 13)
(Page 13)
3-12.LID CD
(Page 14)
SET
ZS-X3CP
8
1
Open the lid CD.
2
screw
(BVTP 3
(BVTP 3
×
14)
Note:
Follow the disassembly procedure in the numerical order given.
3-2.
CABINET LOWER, TELESCOPIC ANTENNA (ANT1)
3
lid battery
4
two screws
(BVTP3
(BVTP3
×
14)
4
five screws
(BVTP3
(BVTP3
×
14)
4
five screws
(BVTP3
(BVTP3
×
14)
6
cabinet lower
7
telescopic antenna
(ANT1)
(ANT1)
A
!
telescopic antenna
(ANT1)
(ANT1)
main chassis
Note: Install the telescopic antenna with engaging
the
!
portion to the main chassis, then
check that the antenna is engaged and
does not move even trying to rotate it
in the direction of arrow
does not move even trying to rotate it
in the direction of arrow
A
.
5
screw
(B3
(B3
×
8)
ZS-X3CP
9
4
audio board
3
three screws
(BVTP3
(BVTP3
×
10)
1
flat cable (18P)
(CNP301)
(CNP301)
2
connector
(CNP901)
(CNP901)
8
battery board
7
claw
5
Remove the connector lead wire
from the incision.
from the incision.
6
terminal
3-3.
MAIN CHASSIS SECTION
3-4.
AUDIO BOARD, BATTERY BOARD
5
flat cable (30P)
(CNP802)
(CNP802)
4
flat cable (21P)
(CNP801)
(CNP801)
2
two screws
(BVTP3
(BVTP3
×
10)
2
two screws
(BVTP3
(BVTP3
×
10)
6
main chassis section
3
1
two connectors
(CN302, CNP303)
(CN302, CNP303)
ZS-X3CP
10
3-5.
TUNER BOARD, CONTROL BOARD
3
two convex portions
2
7
1
screw
(BVTP3
(BVTP3
×
10)
5
tuner board
4
connector
(CNP1)
(CNP1)
8
Remove the lead wires
from the incision.
from the incision.
6
Remove the connector lead wires
from the incision.
from the incision.
0
two screws
(BVTP3
(BVTP3
×
10)
qs
control board
9
flat cable (18P)
(CNP301)
(CNP301)
qa
two claws
Click on the first or last page to see other ZS-X3CP service manuals if exist.