Sony ZS-SAT1 Service Manual ▷ View online
41
ZS-SAT1
•
IC Pin Function Description
XM BOARD IC001 F2602E-01-TR (XM RECEIVER)
Pin No.
Pin Name
I/O
Description
1
LSDP_TXRX
-
Not used
2
VSS
-
Ground terminal
3
SC_XT_OUT
O
Serial data output to the system controller
4
VDD
-
Power supply terminal (+3.3V)
5
SC_RX_IN
I
Serial data input from the system controller
6
VSS
-
Ground terminal
7
CDM_SEL
I
Command mode selection signal input terminal Not used
8
VDD
-
Power supply terminal (+3.3V)
9
ERR_IRQ#
O
Interrupt request signal output terminal Not used
10
VSS
-
Ground terminal
11
RST#
I
Reset signal input from the system controller "L": reset
12
SLAVE_SET
I
Master/slave mode selection signal input terminal "L": master mode, "H": slave mode
Fixed at "L" in this set
Fixed at "L" in this set
13
COMM_RX_DIG
-
Not used
14
COMM_TX_DIG
-
Not used
15
COMM_TX_EN
-
Not used
16
VSS
-
Ground terminal
17
VDD
-
Power supply terminal (+3.3V)
18
CDMM_RX_P
I
XM receiver differential signal (positive) input terminal
19
CDMM_RX_M
I
XM receiver differential signal (negative) input terminal
20
VDD
-
Power supply terminal (+3.3V)
21
VSS
-
Ground terminal
22
CDMM_TX_M
O
XM transmitter differential signal (negative) output terminal
23
CDMM_TX_P
O
XM transmitter differential signal (positive) output terminal
24, 25
VSS
-
Ground terminal
26
OSC_OUT
O
System clock output terminal (45.158 MHz)
27
VSS
-
Ground terminal
28
OSC_IN
I
System clock input terminal (45.158 MHz)
29
VSS
-
Ground terminal
30
TEST
-
Not used
31
VSS
-
Ground terminal
32
HSDP_DATA
-
Not used
33
VDD
-
Power supply terminal (+3.3V)
34
HSDP_CLK
-
Not used
35
VSS
-
Ground terminal
36
HSDP_EN
-
Not used
37
I2S_DA
O
I2S digital audio data output to the D/A converter
38
VSS
-
Ground terminal
39
I2S_CLK
O
I2S bit clock signal output to the D/A converter
40
VDD
-
Power supply terminal (+3.3V)
41
I2S_LRCLK
O
I2S L/R sampling clock signal output to the D/A converter
42
VSS
-
Ground terminal
43
I2S_OCLK
O
I2S over sample clock signal output to the D/A converter
44
VSS
-
Ground terminal
45
SAII_CLK
-
Not used
46
VDD
-
Power supply terminal (+3.3V)
42
ZS-SAT1
Pin No.
Pin Name
I/O
Description
47
SAII_DA
-
Not used
48
SAII_EN
-
Not used
43
ZS-SAT1
MAIN BOARD IC803 MB90F045PF-G-9026-SPE1 (SYSTEM CONTROLLER)
Pin No.
Pin Name
I/O
Description
1
O-BK-LIGHT
O
LED drive signal output terminal for LCD back light "H": LED on
2
O-SAT-LED
O
LED drive signal output terminal for SAT radio "H": LED on
3
LCD-VDDON
O
LCD power supply on/off control signal output terminal "H": LCD power on
4 to 10
NC
O
Not used
11
GND
-
Ground terminal
12
LCD-INHB
O
LCD display control signal output to the LCD driver
13
LCD-RSTB
O
System reset signal output to the LCD driver
14
LCD-CSB
O
Serial data transfer chip select signal output to the LCD driver
15 to 18
NC
O
Not used
19
LCD-SO
O
Serial data output to the LCD driver
20
LCD-SCK
O
Serial data transfer clock signal output to the LCD driver
21
ROM-SDA
I/O
Two-way data bus with the EEPROM
22
ROM-SCL
O
Serial data transfer clock signal output to the EEPROM
23
VCC
-
Power supply terminal (+3.3V)
24
NC
O
Not used
25
O-SAT-SEL
O
Pull up terminal for the XM/SIRIUS mode selection switch
26
I-SAT-SEL
I
XM/SIRIUS mode selection switch input terminal "L": SIRIUS mode, "H": XM mode
27
I-SAT-RXD
I
UART transfer data input from the XM receiver and SIRIUS socket
28
O-SAT-TXD
O
UART transfer data output to the XM receiver and SIRIUS socket
29
XM-RST
O
Reset signal output to the XM receiver "L": reset
30
SAT-SEL
O
XM/SIRIUS mode selection signal output terminal "L": SIRIUS mode, "H": XM mode
31
XM-5VON
O
XM +5.2V power supply on/off control signal output terminal "H": power on
32
SR-ACC
O
SIRIUS power supply on/off control signal output terminal "H": power on
33
VOL-DATA
O
Serial data output to the electrical volume
34
VOL-CLK
O
Serial data transfer clock signal output to the electrical volume
35
AD-VCC
-
Power supply terminal (+3.3V)
36
AD-VREF
-
Reference voltage (+3.3V) terminal
37
AD-VSS
-
Ground terminal
38
REG6V-CHK
I
Input terminal for +6.2V power supply voltage detection
39
REG3V-CHK
I
Input terminal for CD +3.3V power supply voltage detection
40
REG5.1V-CHK
I
Input terminal for SAT +5.2V power supply voltage detection
41
BATCHK-M
I
Input terminal for battery middle voltage (+4.5V) detection
42
GND
-
Ground terminal
43
BATCHK-H
I
Input terminal for battery high voltage and AC power supply (+9V) detection
44 to 46
I-KEY0 to
I-KEY2
I
Front panel key input terminal (A/D input)
47
I-WAKEUP
I
Wake-up signal input terminal
48
A-MUTE
O
Audio muting on/off control signal output terminal "H": muting on
49
MD0
I
Input terminal for mode setting "L": flash writing mode, "H": normal mode
50
MD1
I
Input terminal for mode setting "H": normal and flash writing mode
51
MD2
I
Input terminal for mode setting "L": normal mode, "H": flash writing mode
52
NC
O
Not used
53
BASS-ON
O
Mega bass on/off control signal output terminal "L": Mega bass on
54
CD-ON
O
CD +3.3V power supply on/off control signal output terminal "H": power on
55
I-AC/DC
I
AC/DC power supply detection terminal "L": AC, "H": DC (battery)
56
O-PCONT
O
System power on/off control signal output terminal "H": power on
44
ZS-SAT1
Pin No.
Pin Name
I/O
Description
57
SUBQ
I
Subcode Q sync (S0+S1) detection signal input from the CD DSP
58
DOUT
I
Serial data input from the CD DSP
59
DIN
O
Serial data output to the CD DSP
60
MCK
O
Serial data transfer clock signal output to the CD DSP
61
RW
O
Data read/write selection signal output to the CD DSP
62, 63
SUFFIX0,
SUFFIX1
I
Input terminal for destination discrimination
64
I-RMC
I
SIRCS signal input from the remote control receiver
65
SUFFIX2
I
Input terminal for destination discrimination
66, 67
NC
O
Not used
68
LIM
I
Disc inner position detection signal input terminal
69
BUSY
I
Busy signal input from the CD DSP
70
MP3/CD-RST
O
System reset signal output to the CD DSP "L": reset
71 to 74
NC
O
Not used
75
XM-ON
O
XM +3.3V power supply on/off control signal output terminal "H": power on
76
5.1V-ON
O
SAT +5.2V power supply on/off control signal output terminal "H": power on
77
XRESET
I
System reset signal input from the reset signal generator "L": reset
For several hundreds msec. after the power supply rises, "L" is input, then it changes to "H"
For several hundreds msec. after the power supply rises, "L" is input, then it changes to "H"
78 to 80
NC
O
Not used
81
VSS
-
Ground terminal
82
X0
I
System clock input terminal (5.53 MHz)
83
X1
O
System clock output terminal (5.53 MHz)
84
VCC
-
Power supply terminal (+3.3V)
85
CLKSFT-AM
O
Oscillation frequency selection on/off control signal output terminal for AM
86
CLKSFT-FM
O
Oscillation frequency selection on/off control signal output terminal for FM
87, 88
NC
O
Not used
89
O-TRY-CLS
O
Loading motor control signal output terminal (for loading in)
90
O-TRY-OPN
O
Loading motor control signal output terminal (for loading out)
91
I-TRY-CLS
I
Disc tray close position detection signal input terminal
92
I-TRY-OPN
I
Disc tray open position detection signal input terminal
93 to 95
NC
O
Not used
96
TU-CE
O
Chip enable signal output to the FM/AM PLL "L" active
97
TU-DATA
O
Serial data output to the FM/AM PLL
98
TU-CLK
O
Serial data transfer clock signal output to the FM/AM PLL
99
TU-COUNT
I
Serial count data input from the FM/AM PLL
100
TU-BMUTE
O
Tuner muting on/off control signal output to the FM/AM PLL "H": muting on
Click on the first or last page to see other ZS-SAT1 service manuals if exist.