Sony ZS-M50 Service Manual ▷ View online
– 3 –
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
OR BASE UNIT
OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
breakdown because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also use
the procedure in the printed matter which is included in the repair
parts.
The flexible board is easily damaged and should be handled with
care.
breakdown because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also use
the procedure in the printed matter which is included in the repair
parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission, ob-
serve more than 30 cm away from the objective lens.
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission, ob-
serve more than 30 cm away from the objective lens.
LASER DIODE AND FOCUS SEARCH OPERATION
CHECK
CHECK
1. Close the lid for CD.
2. Press CD
2. Press CD
fl button.
3. Confirm the laser diode emission while observing the objecting
lens. When there is no emission, Auto Power Control circuit or
Optical Pick-up is broken.
Objective lens moves up and down once for the focus search.
Optical Pick-up is broken.
Objective lens moves up and down once for the focus search.
CAUTION DURING WHEN MOUNTING THE PULLEY
FOR THE CD DOOR MOTOR (M703)
FOR THE CD DOOR MOTOR (M703)
Make the following adjustment when mounting the CD door motor
(part number : 1-763-224-11) and motor pulley (part number : 2-
627-174-01) of the CD section.
(part number : 1-763-224-11) and motor pulley (part number : 2-
627-174-01) of the CD section.
Specification : A = 0.9 to 1.1mm
SECTION 1
SERVICE NOTE
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
!
OR DOTTED LINE WITH
MARK
!
ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN
SUPPLEMENTS PUBLISHED BY SONY.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN
SUPPLEMENTS PUBLISHED BY SONY.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270°C during
repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering or
unsoldering.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-
• Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
CHUCK PLATE JIG ON REPAIRING
On repairing CD section, playing a disc without the CD lid, use
Chuck Plate Jig.
• Code number of Chuck Plate Jig : X-4918-255-1
Chuck Plate Jig.
• Code number of Chuck Plate Jig : X-4918-255-1
– 4 –
ABOUT THE BD BOARD WAVEFORM CHECKING JIG
The special jig (J-2501-124-A) is highly convenient when check-
ing the waveform of the BD board of the MD section. Pin names
and items to check are as follows:
ing the waveform of the BD board of the MD section. Pin names
and items to check are as follows:
I+3V : for IOP measurement (check for depleted optical pickup
laser)
IOP
: for IOP measurement (check for depleted optical pickup
laser)
TEO : TRK error signal (traverse adjustment)
VC
VC
: Standard level for checking signals
RF
: RF signal (jitter check)
BD board
CN110
DG board
I + 3V
IOP
TEO
VC
RF
Jig
(J-2501-124-A)
MD block section
ABOUT THE HARDWARE RESET
It is possible to reset the system microcomputer by pressing the
RESET button located on the bottom with a pointed object. Use
this button when the unit cannot be operated properly due to such
problems as microcomputer errors, etc.
RESET button located on the bottom with a pointed object. Use
this button when the unit cannot be operated properly due to such
problems as microcomputer errors, etc.
RESET button
(Located on the bottom)
– 5 –
SECTION 2
GENERAL
LOCATION AND FUNCTION OF CONTROLS
1 MD operation buttons
fl (play/pause)
π (stop)
π (stop)
2 BAND button
3 CD operation buttons
3 CD operation buttons
fl (play/pause)
π (stop)
π (stop)
4 CD lid
5 6 CD OPEN/CLOSE button
6 6 MD EJECT button
7 MONO/ST, REPEAT button
8 AUTO PRESET/RDS/SHUF/PGM button
9 TUNE +, ÷, ) button
5 6 CD OPEN/CLOSE button
6 6 MD EJECT button
7 MONO/ST, REPEAT button
8 AUTO PRESET/RDS/SHUF/PGM button
9 TUNE +, ÷, ) button
!º YES, ENTER button
!¡ Jog dial
!¡ Jog dial
=/+ AMS
PRESET
PRESET
!™ NO, CANCEL button
!£ TUNE –, ¿, 0 button
!¢ EDIT button
!∞ REC button
!§ REC IT button
!£ TUNE –, ¿, 0 button
!¢ EDIT button
!∞ REC button
!§ REC IT button
TO TOP, TO END
!¶ SYNCHRO REC
CD
” MD button
!• MD insert section
!ª LINE/LINE LEVEL button
@º Display window
@¡ VOLUME +, – buttons
@™ BASS/TREBLE button
@£ MEGA BASS button
@¢ Jog dial Function indicator
@º Display window
@¡ VOLUME +, – buttons
@™ BASS/TREBLE button
@£ MEGA BASS button
@¢ Jog dial Function indicator
AMS/PRESET SELECT
@∞ LINE IN terminal
@§ DISPLAY button
@¶ INSERT/TIMER button
@• DELETE/CLOCK button
@ª 2 (Headphones) Jack (stereo mini jack)
#º STANDBY button
#¡ SLEEP button
#™ Remote control receiver section
#£ OPERATE button
@¶ INSERT/TIMER button
@• DELETE/CLOCK button
@ª 2 (Headphones) Jack (stereo mini jack)
#º STANDBY button
#¡ SLEEP button
#™ Remote control receiver section
#£ OPERATE button
FRONT PANEL: MD/CD/RADIO Section
FRONT PANEL: TIMER, COM Section
– 6 –
REAR PANEL Section
1 TA SERCH button
2 CD OPEN/CLOSE button
3 Numeric buttons
4 MODE button
5 BASS/TREBLE +, – buttons
6 MEGA BASS button
7 MD operation buttons
2 CD OPEN/CLOSE button
3 Numeric buttons
4 MODE button
5 BASS/TREBLE +, – buttons
6 MEGA BASS button
7 MD operation buttons
” (play)
P (pause)
p (stop)
r (rec)
8 CD operation buttons
” (play)
P (pause)
p (stop)
9 RADIO operation buttons
BAND
TUNE –, +
!º OPERATE button
!¡ VOL +, – buttons
!™ =, + AMS, select, search buttons
!º OPERATE button
!¡ VOL +, – buttons
!™ =, + AMS, select, search buttons
#¢ MW/LW ANTENNA terminal
#∞ FM EXT ANTENNA terminal
#§ FM rod antenna
#¶ ⁄ AC IN jack
#• Battery compartment (for memory back-up)
#ª RESET button (bottom)
$º FM ANTENNA SELECTOR switch
#∞ FM EXT ANTENNA terminal
#§ FM rod antenna
#¶ ⁄ AC IN jack
#• Battery compartment (for memory back-up)
#ª RESET button (bottom)
$º FM ANTENNA SELECTOR switch
REMOTE CONTROL Section
OPERATE
TA
SEARCH