Sony ZS-M30 Service Manual ▷ View online
4
ZS-M30
1-7. CHECKS PRIOR TO PARTS REPLACEMENT AND ADJUSTMENTS (FOR MD SECTION)
Before performing repairs, perform the following checks to determine the faulty locations up to a certain extent.
Details of the procedures are described in “5 Electrical Adjustments”
Details of the procedures are described in “5 Electrical Adjustments”
Laser power check
Criteria for Determination
(Unsatisfactory if specified value is not satisfied)
(Unsatisfactory if specified value is not satisfied)
Note:
The criteria for determination above is intended merely to determine if satisfactory or not, and does not serve as the specified value for
adjustments.
When performing adjustments, use the specified values for adjustments.
The criteria for determination above is intended merely to determine if satisfactory or not, and does not serve as the specified value for
adjustments.
When performing adjustments, use the specified values for adjustments.
Measure if unsatisfactory:
• Clean the optical pick-up
• Adjust again
• Replace the optical pick-up
• Adjust again
• Replace the optical pick-up
• 0.9 mW power
Specified value : 0.80 to 0.96 mW
• 7.0 mW power
Specified value : 6.8 to 7.2 mW
lop (at 7mW)
• Labeled on the optical pickup
Iop value
±
10%
• Replace the optical pick-up
If always unsatisfactory:
• Replace the overwrite head
• Check for disconnection of the circuits around the
• Replace the overwrite head
• Check for disconnection of the circuits around the
overwrite head
If occasionally unsatisfactory:
• Check if the overwrite head is distorted
• Check the mechanism around the sled
• Check if the overwrite head is distorted
• Check the mechanism around the sled
• Error rate check
Specified value : For points a and b
C1 error : About 200
ADER : Below 2
Point C
C1 error :Below 50
AD error :Below 2
C1 error : About 200
ADER : Below 2
Point C
C1 error :Below 50
AD error :Below 2
• Error rate check
Specified value:
a. When using test disc (MDW-74/AU-1)
a. When using test disc (MDW-74/AU-1)
C1 error : Below 80
ADER : Below 2
ADER : Below 2
b. When using check disc (TDYS-1)
C1 error : Below 50
• CPLAY error rate check
Specified value:
C1 error : Below 80
ADER : Below 2
C1 error : Below 80
ADER : Below 2
• Replace the optical pick-up
• Replace the optical pick-up
Focus power check
C PLAY check
Self-recording/playback
check
check
5
ZS-M30
SECTION 2
GENERAL
This section is extracted from
instruction manual.
instruction manual.
6
ZS-M30
7
ZS-M30
SECTION 3
DISASSEMBLY
Note : Follow the disassembly procedure in the numerical order given.
3-1. CABINET (REAR), CABINET (FRONT)
3-2. BATT (B) BOARD, BATT (A) BOARD, POWER BOARD
r
The equipment can be removed using the following procedure.
Set
Cabinet (rear)
Cabinet (front)
BATT (B) board, BATT (A) board, power board
Cabinet
(upper)
ASSY
(upper)
ASSY
Main board,
LCD board
LCD board
SW (L) board,
jack board,
SW (R) board
jack board,
SW (R) board
REC board,
detect board
detect board
Over write head (HR901),
MD optical pick-up,
D SW board
MD optical pick-up,
D SW board
MD block
ASSY
ASSY
CD board
MD board
TOP board
Tuner
board
board
4
2
7
9
Cabinet (rear)
BATT (A) board
Chissis, transformer
BATT (B) board
Power board
5
Screws (+BVTP 3 X 12) (silver)
8
Screws (+BVTP 3 X 10)
6
Screws (+BVTP 3 X 10)
0
CN902
1
Claw
3
Claw
4
Main board
CN801
Cabinet (front)
Cabinet (rear)
2
Screws
(+BVTP 3 X 12) (silver)
2
Screws
(+BVTP 3 X 12) (silver)
1
Screws (+BVTP 3 X 14)
1
Screws
(+BVTP 3 X 14)
3