Sony XDR-S10DAB Service Manual ▷ View online
XDR-S10DAB
5
3-3. FRONT BLOCK
screw (B2.6 BV)
front block
white
SP102 (R-ch)
SP102
SP101 (L-ch)
SP101
Remove four speaker cables.
Open the connector.
pink/white
red
black
CN101
3-4. SPEAKER (6.8cm) (SP101/SP102)
four wood screws
Remove two solders.
speaker (6.8cm)
(SP101)
(SP101)
four wood screws
speaker (6.8cm)
(SP102)
(SP102)
Remove two solders.
XDR-S10DAB
6
3-5. CABINET (FRONT) ASSY
3-6. DAB TUNER MODULE (TU1)
RI cabinet (front) section
knob (tune)
button (power)
cap (button)
(SLEEP)
(SLEEP)
cap (button)
(DISPLAY)
(DISPLAY)
RB cap (button)
(DAB/FM)
(DAB/FM)
RT cap (button) (PRESET)
RE cap (button) (MENU)
RG cap (button) (ENTER)
RH six adhesive sheets (cap)
Remove the VOLUME board.
two screws
(B2.6
(B2.6
BV)
screw (B2.6 BV)
four screws
(B2.6
(B2.6
P)
two screws
(B2.6
(B2.6
P)
knob (vol)
claw
Remove two solders.
two screws
(B2.6
(B2.6
P)
DAB tuner module (TU1)
shield case (DAB)
XDR-S10DAB
7
3-7. CHASSIS
claw
MAIN board block
eight screws
(B2.6
(B2.6
P)
chassis
four screws
(B2.6
(B2.6
P)
claw
Remove the KEY board
in the direction of the arrow.
SECTION 4
TEST MODE
LCD TEST MODE
Procedure:
1. In the power off status, press three buttons of [DISPLAY],
Procedure:
1. In the power off status, press three buttons of [DISPLAY],
[MENU] and [ENTER] for 5 seconds.
2. All segments on the liquid crystal display light up.
3. To release the LCD test mode, press the [POWER] button.
3. To release the LCD test mode, press the [POWER] button.
XDR-S10DAB
8
For Schematic Diagrams.
Note:
• All capacitors are in μF unless otherwise noted. (p: pF)
50 WV or less are not indicated except for electrolytics
• All capacitors are in μF unless otherwise noted. (p: pF)
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in
Ω and
1
/
4
W or less unless otherwise
specifi ed.
• C : panel designation.
• A : B+ Line.
• Voltages and are dc with respect to ground under no-sig-
• Voltages and are dc with respect to ground under no-sig-
nal (detuned) conditions.
no mark : TUNER (DAB/FM)
• Voltages are taken with a VOM (Input impedance 10
• Voltages are taken with a VOM (Input impedance 10
M
Ω).
Voltage variations may be noted due to normal production
tolerances.
• Signal path.
F :
F :
TUNER
(DAB/FM)
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is printed in each block.)
(In addition to this, the necessary note is printed in each block.)
For Printed Wiring Boards.
Note:
• X : Parts extracted from the component side.
• Y : Parts extracted from the conductor side.
•
• X : Parts extracted from the component side.
• Y : Parts extracted from the conductor side.
•
: Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)
• Circuit Boards Location
SECTION 5
DIAGRAMS
MAIN board
DAB tuner module (TU1)
JACK (DC) board
JACK (HEADPHONE) board
VOLUME board
KEY board
Click on the first or last page to see other XDR-S10DAB service manuals if exist.