Sony XDR-S10DAB Service Manual ▷ View online
XDR-S10DAB
4
SECTION 3
DISASSEMBLY
• This set can be disassembled in the order shown below.
3-1. DISASSEMBLY FLOW
Note: Follow the disassembly procedure in the numerical order given.
3-2. CABINET
(REAR)
3-2. CABINET
(REAR)
(Page
4)
3-3. FRONT
BLOCK
(Page
5)
3-4. SPEAKER (6.8cm) (SP101/SP102)
(Page
(Page
5)
3-5. CABINET
(FRONT)
ASSY
(Page
6)
SET
3-6. DAB TUNER MODULE (TU1)
(Page
(Page
6)
3-7. CHASSIS
(Page
(Page
7)
telescopic antenna (ANT1)
screw (M3 × 6)
RT cover (handle)
RB two screws (B2.6)
Remove the contact plate (ANT).
RE cabinet (rear)
cord retainer PWB
Remove the JACK (DC) board
in the direction of the arrow.
two screws
(B2.6
(B2.6
BV)
screw (B2.6)
R Remove the JACK (HEADPHONE) board
in the direction of the arrow.
six screws
(B2.6)
(B2.6)
XDR-S10DAB
5
3-3. FRONT BLOCK
screw (B2.6 BV)
front block
white
SP102 (R-ch)
SP102
SP101 (L-ch)
SP101
Remove four speaker cables.
Open the connector.
pink/white
red
black
CN101
3-4. SPEAKER (6.8cm) (SP101/SP102)
four wood screws
Remove two solders.
speaker (6.8cm)
(SP101)
(SP101)
four wood screws
speaker (6.8cm)
(SP102)
(SP102)
Remove two solders.
XDR-S10DAB
6
3-5. CABINET (FRONT) ASSY
3-6. DAB TUNER MODULE (TU1)
RI cabinet (front) section
knob (tune)
button (power)
cap (button)
(SLEEP)
(SLEEP)
cap (button)
(DISPLAY)
(DISPLAY)
RB cap (button)
(DAB/FM)
(DAB/FM)
RT cap (button) (PRESET)
RE cap (button) (MENU)
RG cap (button) (ENTER)
RH six adhesive sheets (cap)
Remove the VOLUME board.
two screws
(B2.6
(B2.6
BV)
screw (B2.6 BV)
four screws
(B2.6
(B2.6
P)
two screws
(B2.6
(B2.6
P)
knob (vol)
claw
Remove two solders.
two screws
(B2.6
(B2.6
P)
DAB tuner module (TU1)
shield case (DAB)
XDR-S10DAB
7
3-7. CHASSIS
claw
MAIN board block
eight screws
(B2.6
(B2.6
P)
chassis
four screws
(B2.6
(B2.6
P)
claw
Remove the KEY board
in the direction of the arrow.
SECTION 4
TEST MODE
LCD TEST MODE
Procedure:
1. In the power off status, press three buttons of [DISPLAY],
Procedure:
1. In the power off status, press three buttons of [DISPLAY],
[MENU] and [ENTER] for 5 seconds.
2. All segments on the liquid crystal display light up.
3. To release the LCD test mode, press the [POWER] button.
3. To release the LCD test mode, press the [POWER] button.