Sony TCS-30D Service Manual ▷ View online
– 5 –
CABINET (REAR), “LID BLOCK ASSY, CASSETTE”
Note:
Follow the disassembly procedure in the numerical order given.
SECTION 3
DISASSEMBLY
• This set can be disassembled in the order shown below.
SET
CABINET (REAR),
“LID BLOCK ASSY, CASSETTE”
MAIN BOARD,
MECHANISM DECK (MT-30D-118)
BELT
8
lid block assy, cassette
INSTALLATION “SPRING, CASSETTE”
cabinet (front)
5
strap, hand
3
claw
3
four claws
2
screw
(IB lock)
(IB lock)
4
cabinet (rear)
1
three screws
(B1.7
(B1.7
×
10)
7
boss
7
boss
6
Remove five solders.
lid, cassette
spring, cassette
spring, cassette
– 6 –
MAIN BOARD, MECHANISM DECK (MT-30D-118)
BELT
6
claw
2
screw
(1.7)
(1.7)
3
screw
(M1.4)
(M1.4)
4
MAIN board
7
mechanism deck
(MT-30D-118)
(MT-30D-118)
5
three screws
(IB lock)
(IB lock)
1
Remove two solders of
electret condenser microphone
(MIC901).
electret condenser microphone
(MIC901).
1
Remove four solders of
magnetic head (HRP901).
magnetic head (HRP901).
1
Remove two solders of
motor (M901).
Cabinet (front)
1
belt (capstan)
2
belt (FR)
capstan belt
FR belt
pulley (FR) assy
flywheel assy
motor, DC
– 7 –
INSTALLATION MAIN BOARD
NOTE: On installation MAIN board, adjust to the
S301 and the S303.
screw
(1.7)
(1.7)
screw
(M1.4)
(M1.4)
MAIN board
S301 (REC/PB)
S303
(POWER)
(POWER)
lever (REC)
– 8 –
Mode
Torque Meter
Meter Reading
4.90 mN•m
FWD
CQ-403C
(more than 50 g)
(more than 1.76 oz)
Mode
Torque Meter
Meter Reading
FWD
2.16 - 4.7 mN•m
(22 - 48 g•cm)
CQ-102C
(0.31 - 0.67 oz•inch)
FWD
0.05 - 0.29 mN•m
(0.5 - 3 g•cm)
Back Tension
(0.007 - 0.04 oz•inch)
FF
4.90 mN•m
CQ-201B
(more than 50 g•cm)
REW
(more than 0.69 oz•inch)
SECTION 4
MECHANICAL ADJUSTMENTS
Tape Tension Measurement
1. Clean the following parts with a denatured-alcohol-moistened
swab:
record/playback head
pinch roller
erase head
rubber belt
capstan
idlers
2. Demagnetize the record/playback head with a head demagne-
tizer. (Do not bring the head demagnetizer close to the erase
head)
head)
3. Do not use a magnetized screwdriver for the adjustments.
4. After the adjustments, apply suitable locking compound to the
4. After the adjustments, apply suitable locking compound to the
parts adjusted.
5. The adjustments should be performed with the rated power
supply voltage (2.5 V) unless otherwise noted.
Torque Measurement
Click on the first or last page to see other TCS-30D service manuals if exist.