Sony TA-SA500WR / TA-SA600WR / TA-SA700WR Service Manual ▷ View online
TA-SA500WR/SA600WR/SA700WR
6
SECTION 2
DISASSEMBLY
• This set can be disassembled in the order shown below.
2-1. DISASSEMBLY FLOW
Note:
Follow the disassembly procedure in the numerical order given.
2-2. TOP COVER
2-5. SWITCHING
REGULATOR
(Page
8)
2-4. WLK6-MAIN
BOARD
(Page
7)
SET
2-3. FRONT
PANEL
ASSY
(Page
7)
2-2. TOP
COVER
(Page
6)
Ver. 1.3
1 two screws
(+BV3
(+BV3
(3-CR))
2 three screws
(+BV3
(+BV3
(3-CR))
4 top cover
3
3
TA-SA500WR/SA600WR/SA700WR
7
2-3. FRONT PANEL ASSY
2-4. WLK6-MAIN BOARD
Ver. 1.3
1 wire (flat type)
(26 core) (CN301)
2 two claws
3 claw
4 front panel assy
3 claw
1 Wire is removed
from the pin, wire.
2 CN501 (4P)
9 WLK6-MAIN board
4 CN101
(7P)
(7P)
5 two screws
(+BV3
(+BV3
(3-CR))
7 four screws
(+BV3
(+BV3
(3-CR))
8 one screw
(+BV3
(+BV3
(3-CR))
6 heatsink
3 Remove the cable from the hook.
(SA600WR)
(SA600WR)
front side
pin, wire
WLK6-MAIN board
REGULATOR, SWITCHING
:LUHVHWWLQJ
TA-SA500WR/SA600WR/SA700WR
8
2-5. SWITCHING REGULATOR
Ver. 1.3
1 CN1 (2P)
4 REGULATOR, SWITCHING
2 four screws
(+BV3
(+BV3
(3-CR))
3 holder, PC board
TA-SA500WR/SA600WR/SA700WR
9
SECTION 3
TEST MODE
COLD RESET
Note:
The main unit corresponding to the surround amplifier (TA-
SA500WR or TA-SA600WR or TA-SA700WR), and the remote com-
mander corresponding to the main unit are necessary to execute this mode.
mander corresponding to the main unit are necessary to execute this mode.
Procedure:
1. Connect the AC power cord of the main unit.
2. Press
1. Connect the AC power cord of the main unit.
2. Press
[\/1] button on the main unit to turn the system on.
"/1
[ ] button
3. Connect the AC power cord of the surround amplifier (TA-
SA500WR or TA-SA600WR or TA-SA700WR).
4. When wireless transmission is activated, the [LINK/STAND-
BY] indicator of the surround amplifier (TA-SA500WR or TA-
SA600WR or TA-SA700WR) turns green.
SA600WR or TA-SA700WR) turns green.
Note:
Refer to the operating instructions when the [LINK/STAND-
BY] indicator of the surround amplifier (TA-SA500WR or
TA-SA600WR or TA-SA700WR) doesn’t light.
TA-SA600WR or TA-SA700WR) doesn’t light.
[LINK/STANDBY] indicator
5. Press the button in order of the [
x
]
[DISPLAY]
[RETURN]
[M] on the remote commander corresponding
to main unit aiming at the main unit.
6. Confirm the [LINK/STANDBY] indicator of the surround am-
plifier (TA-SA500WR or TA-SA600WR or TA-SA700WR) is
orange lighting after step 5 is executed.
orange lighting after step 5 is executed.
7. The AC power cord of the surround amplifier (TA-SA500WR
or TA-SA600WR or TA-SA700WR) is pulled out to turn off
the system.
the system.
Note:
Please insert it after confirming the [LINK/STANDBY]
indicator of the surround amplifier (TA-SA500WR or TA-
SA600WR or TA-SA700WR) has been turned off when you
insert the AC power cord again.
indicator of the surround amplifier (TA-SA500WR or TA-
SA600WR or TA-SA700WR) has been turned off when you
insert the AC power cord again.
Click on the first or last page to see other TA-SA500WR / TA-SA600WR / TA-SA700WR service manuals if exist.