DOWNLOAD Sony TA-FB720R / TA-FB820R Service Manual ↓ Size: 2.76 MB | Pages: 26 in PDF or view online for FREE

Model
TA-FB720R TA-FB820R
Pages
26
Size
2.76 MB
Type
PDF
Document
Service Manual
Brand
Device
Audio
File
ta-fb720r-ta-fb820r.pdf
Date

Sony TA-FB720R / TA-FB820R Service Manual ▷ View online

– 2 –
SAFETY-RELATED COMPONENT WARNING !!
COMPONENTS IDENTIFIED BY MARK 
!
 OR DOTTED LINE
WITH MARK 
!
 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
TABLE OF CONTENTS
1. GENERAL
.......................................................................... 3
2. ELECTRICAL ADJUSTMENT
..................................... 4
3. DIAGRAMS
3-1. Circuit Boards Location ........................................................ 5
3-2. Schematic Diagram – Input Section – .................................. 7
3-3. Printed Wiring Board – Input Section – ................................ 9
3-4. Schematic Diagram – Main Section – ................................ 11
3-5. Printed Wiring Board – Main Section – .............................. 13
3-6. Schematic Diagram – Panel Section – ................................ 15
3-7. Printed Wiring Board – Panel Section – ............................. 17
3-8. Schematic Diagram – Power Section – ............................... 19
3-9. Printed Wiring Board – Power Section – ............................ 21
3-10. IC Block Diagrams ............................................................ 23
3-11. IC Pin Function ................................................................. 24
4. EXPLODED VIEW
4-1. Case and Back Panel Section .............................................. 25
4-2. Front Panel Section ............................................................. 26
4-3. Chassis Section ................................................................... 27
5. ELECTRICAL PARTS LIST
........................................ 28
– 3 –
Front Panel Descriptions
SECTION 1
GENERAL
1
PROTECTION indicator
2
U (Power) button
3
Remote sensor
4
TAPE 1/DAT indicator
5
TAPE 2/MD indicator
6
AUX indicator
7
CD indicator
8
TUNER indicator
9
PHONO indicator
10
INPUT SELECTOR knob
11
VOLUME knob
12
SUBSONIC button
13
SOURCE DIRECT button and indicator
14
LOUDNESS button
15
TAPE MONITOR knob
16
BALANCE knob
17
TREBLE knob
18
BASS knob
19
SPEAKERS knob
20
PHONE jack
21
EON LINK button
This section is extracted from
instruction manual.
10
3
2
1
9
7
8
4
6
5
11
13
12
14
15
16
17
18
19
20
21
– 4 –
SECTION  2
ELECTRICAL ADJUSTMENT
Bias Adjustment
NOTE:
1. Perform the adjustment after the unit has warmed up sufficiently.
2. Perform the bias adjustment if the power transistor has been
replaced.
Procedure:
1. Rotate fully the bias adjusting semi-fixed resistors (RV500,
RV600) to the MIN position (counterclockwise).
2. Connect a digital voltmeter to the CN500 and CN600.
3. Set the slide regulator to 0V, and press the  U  button (ON) on
the set.
4. Raise gradually the slide regulator voltage up to the rated voltage.
5. At this time, confirm that the SP relay is turned on (it will click).
6. Adjust the RV500 and RV600 so that a reading of digital
voltmeter is 10 ± 0.1 mV.
7. Return the slidack to 0 V, and press the  U  button (OFF) on the
set.
Adjustment Location :
[MAIN BOARD] – COMPONENT SIDE –
1 pin
3 pin
+
+
CN500 (L-CH)
CN600(R-CH)
+
CN600 (R-CH)
1
3
CN500 (L-CH)
1
3
RV600
Bias (R-CH)
RV500
Bias (L-CH)
DIGITAL
VOLTMETER
DIGITAL
VOLTMETER
+
– 5 –
– 6 –
SECTION  3
DIAGRAMS
3-1. CIRCUIT BOARDS LOCATION
THIS NOTE IS COMMON FOR PRINTED WIRING
BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is printed
in each block.)
For schematic diagrams.
Note:
• All capacitors are in µF unless otherwise noted.  pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in 
 and 
1
/
4
 
W or less unless otherwise
specified.
¢
: internal component.
2
: nonflammable resistor.
5
: fusible resistor.
C
: panel designation.
For printed wiring boards.
Note:
X
: parts extracted from the component side.
Y
: parts extracted from the conductor side.
b
: Pattern from the side which enables seeing.
U
: B+ Line.
V
: B– Line.
H
: adjustment for repair.
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : POWER ON
• Voltages are taken with a VOM (Input impedance 10 M
).
Voltage variations may be noted due to normal produc-
tion tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal produc-
tion tolerances.
• Circled numbers refer to waveforms.
• Signal path.
F
: TUNER
WAVEFORM
1
IC902 
1
 XOUT
Note: The components identified by mark 
!
 or dotted line
with mark 
!
 are critical for safety.
Replace only with part number specified.
• Indication of transistor
C
These are omitted
E
B
4MHz
3.8Vp-p
PANEL board
INPUT board
MAIN board
SP-TM board
PHONO board
PS board
OUTLET board
VOL board
SIRCS board
SIRCS SUB board
HP board
SP-SW board
Page of 26
Display

Sony TA-FB720R / TA-FB820R Service Manual ▷ Download

  • DOWNLOAD Sony TA-FB720R / TA-FB820R Service Manual ↓ Size: 2.76 MB | Pages: 26 in PDF or view online for FREE
  • Here you can View online or download the Service Manual for the Sony TA-FB720R / TA-FB820R in PDF for free, which will help you to disassemble, recover, fix and repair Sony TA-FB720R / TA-FB820R Audio. Information contained in Sony TA-FB720R / TA-FB820R Service Manual (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.