Sony STR-KIV300 Service Manual ▷ View online
STR-KIV300
9
2-6. IO-TUNER BOARD, DC FAN, SHIELD PLATE (POWER CORD)
:LUHVHWWLQJ
switching regulator (SWR1)
rear side
IO-TUNER board
AMP board
1 CN4001 (2P)
6 IO-TUNER board
5 Wire is removed
from pin, lead
from pin, lead
3 one screw
(+BV3 (3-CR))
(+BV3 (3-CR))
2 CN4000 (19P)
4 three screws (+BV3 (3-CR))
q; one screw (+BV3 (3-CR))
7 two screws (+BV3 (3-CR))
qa one screw (+BV3 (3-CR))
qs shield plate (power cord)
9 CN1 (2P)
8 DC fan
2-7. MB1306 BOARD
3 four screws
(+BV3
(+BV3
(3-CR))
1 CN5301 (9P)
2 CN6305 (24P)
5 heat sink, MB
7 MB1306 board
6 sheet, radiation
4 three screws
(+B 3
(+B 3
u5)
STR-KIV300
10
2-8. AMP BOARD
1 CN4 (3P)
2 CN101 (4P)
3 four screws
(+BV3
(+BV3
(3-CR))
7 AMP board
4 three screws
(+BV3
(+BV3
(3-CR))
6 two screws
(+BV3
(+BV3
(3-CR))
5 heat sink, DAMP
2-9. SWITCHING REGULATOR (SWR1)
2 switching regulator (SWR1)
1 five screws (+BV3 (3-CR))
STR-KIV300
11
SECTION 3
TEST MODE
COLD RESET
The cold reset clears certain data in this system without initialize
Personal Information and some BD operation data. Execute this
mode when returning the unit to the customers.
Procedure:
1. Press the [
The cold reset clears certain data in this system without initialize
Personal Information and some BD operation data. Execute this
mode when returning the unit to the customers.
Procedure:
1. Press the [
?/1
] button to turn the power on.
2. Press the [VOL -] and [FUNCTION] buttons simultaneously
and hold down (around 5 seconds).
3. The message “WAIT” appears then “RESET” appears on fl uo-
rescent indicator tube, then becomes standby states.
DEMO MODE
This mode is prepared for exhibition environmental improvement.
The message “D. MODE” will be displayed on the fluorescent
indicator tube.
Procedure:
1. Press the [
This mode is prepared for exhibition environmental improvement.
The message “D. MODE” will be displayed on the fluorescent
indicator tube.
Procedure:
1. Press the [
?/1
] button to turn the power on.
2. Press the [FUNCTION] button to select the “HDMI 1”.
3. Press button in order of the [
3. Press button in order of the [
x
]
→ [DISPLAY] → [
<
]
→ [
M
]
on the remote commander (make the interval when each button
is pressed within two seconds). The message “D. MODE”
displayed on the fluorescent indicator tube.
is pressed within two seconds). The message “D. MODE”
displayed on the fluorescent indicator tube.
Releasing method:
Press button in order of the [
Press button in order of the [
x
]
→ [DISPLAY] → [
<
]
→ [
M
]
on the remote commander (make the interval when each button is
pressed within two seconds). The message “D. OFF” displayed on
the fl uorescent indicator tube.
pressed within two seconds). The message “D. OFF” displayed on
the fl uorescent indicator tube.
PANEL TEST
Procedure:
1. Press the [
Procedure:
1. Press the [
?/1
] button to turn the power on.
2. Press button in order of the [
x
]
→ [DISPLAY] → [
m
]
→ [
M
]
on the remote commander (Make the interval when each but-
ton is pressed within two seconds).
ton is pressed within two seconds).
3. All
segments
in
fl uorescent indicator tube are lighted up. And
half segments in fl uorescent indicator tube are lighted up, oth-
ers half segments in fl uorescent indicator tube are lighted up,
then all segments in fl uorescent indicator tube are lighted up.
This operation is repeated.
ers half segments in fl uorescent indicator tube are lighted up,
then all segments in fl uorescent indicator tube are lighted up.
This operation is repeated.
4. In the state of step 3, press the [VOL +] button on the remote
commander and model information is displayed on the fl uores-
cent indicator tube.
cent indicator tube.
Each time the [VOL +] button on the remote commander is
pressed, the display changes from destination information,
STR version, special mode in this order, and returns to the
model information display.
pressed, the display changes from destination information,
STR version, special mode in this order, and returns to the
model information display.
5. In the state of step 3, press the [FUNCTION] button on the
remote commander and “K 0” is displayed on the fluorescent
indicator tube.
indicator tube.
“K 0” value increases whenever a button or sensor on the unit
is pressed. However, once a button or sensor has been pressed,
it is no longer taken into account.
is pressed. However, once a button or sensor has been pressed,
it is no longer taken into account.
All button and sensors on the unit are pressed, “OK” and “K4”
are alternately displayed on the fluorescent indicator tube.
are alternately displayed on the fluorescent indicator tube.
Releasing method:
To release from this mode, press the [
To release from this mode, press the [
?/1
] button.
FACTORY INITIALIZE
Return all of the unit setting to their factory defaults.
Return all of the unit setting to their factory defaults.
Note 1: Disconnect the following connections when you use this mode.
• USB
Note 2: The operation in this mode must use a remote commander and TV
monitor.
Procedure:
1. Press the [
1. Press the [
?/1
] button to turn the power on.
2. Press the [HOME] button on the remote commander, and the
home menu is displayed.
3. Select
“Setup”
→ “Resetting”, and press the [ ] button on the
remote commander.
Resetting
Easy Initial Settings - OSD Langguage
4. Select “Initialise Personal Information”, and press the [
]
button on the remote commander.
Initialise Personal Information
Delete personal data when disposing
Delete personal data when disposing
Reset to Factory Default Settings
5. Select “OK”, and press the [
] button on the remote com-
mander.
Initialise Personal Information
OK
Cancel
Deleting Personal Information.
Do you want to proceed?
If you destroy or transfer or resell this
unit, please delete all Personal Information
for security reasons.
Please take appropriate measures such as
logging out after using a network service.
Do you want to proceed?
If you destroy or transfer or resell this
unit, please delete all Personal Information
for security reasons.
Please take appropriate measures such as
logging out after using a network service.
STR-KIV300
12
SVC SERVICE MODE
Note: The operation in this mode must use a remote commander and TV
monitor.
Setting method of the SVC service mode:
1. Connect this unit with TV monitor.
2. Press the [
1. Connect this unit with TV monitor.
2. Press the [
?/1
] button to turn the power on.
3. Press button in order of the [
x
]
→ [DISPLAY] → [
X
]
→ [
M
]
on the remote commander. (Make the interval when each but-
ton is pressed within two seconds)
ton is pressed within two seconds)
4. The message “SVC” displayed on the fl uorescent indicator
tube. The OSD menu on TV monitor can be operated by re-
mote commander.
mote commander.
1. Main
Functions
• Diag
Performs unit test of devices installed on the board.
• Log
Error log is displayed. Displayed contents can also be saved in
an USB memory device.
an USB memory device.
• Factory
Initialize
Restores the unit to its factory settings.
• Network
Checks the wired network connection.
• Version
Up
• System
Information
Displays the system information of the unit.
Displays information such as the software version, drive infor-
mation, etc.
mation, etc.
• EMC
Test
Mode
Not
used.
• Drive
Write drive OP data and check drive.
• HDD
Mode
Not
used.
6. The message “Close” appears, and press the [
] button on the
remote commander.
Initialise Personal Information
Close
Initialisation complete.
7. Select “Reset to Factory Default Settings”, and press the [
]
button on the remote commander.
Initialise Personal Information
Reset to Factory Default Settings
Restore each setting to the factory
default setting.
Restore each setting to the factory
default setting.
8. Select “All Settings”, and press the [
] button on the remote
commander.
Reset to Factory Default Settings
Screen Settings
Audio Settings
BD/DVD Viewing Settings
Parental Control Settings
System Settings
External Input Settings
Network Settings
All Settings
Audio Settings
BD/DVD Viewing Settings
Parental Control Settings
System Settings
External Input Settings
Network Settings
All Settings
9. Select “Start”, and press the [
] button on the remote com-
mander.
All Settings
Restore all settings to the factory default
settings. The system will turn off after
reset.
settings. The system will turn off after
reset.
Start
Cancel
10. Initialisation ends when the message “HELLO” on the fl uores-
cent indicator tube disappears.
Click on the first or last page to see other STR-KIV300 service manuals if exist.