DOWNLOAD Sony STR-K885 Service Manual ↓ Size: 4.06 MB | Pages: 60 in PDF or view online for FREE

E Model

Australian Model

2007H16-1
© 2007.08

• STR-K885 is the tuner and the amplifier section

in HT-DDW885.

This receiver incorporates Dolby* Digital and Pro Logic Surround and
the DTS** Digital Surround System.
*

Manufactured under license from Dolby Laboratories. “Dolby”, “Pro
Logic”, “Surround EX”, and the double-D symbol are trademarks of
Dolby Laboratories.

** “DTS” and “DTS-ES Neo:6” are registered trademarks of DTS, Inc.

“96/24” is a trademark of DTS, Inc.

— Continued on next page —

Models of area code SP, SP6, AUS, E51

Stereo mode (6 ohms, 1 kHz, THD 1%)

90 W + 90 W

1)

Surround mode

2)

 (reference) (6 ohms, 1 kHz, 

THD 10%)

RMS output

FRONT: 135 W 

 

per channel

1)

CENTER:135 W

1)

SURROUND: 135 W

 

per channel

1)

SURROUND BACK:

 

135 W

1)

Models of area code AR

Stereo mode (6 ohms, 1 kHz, THD 1%)

90 W + 90 W

1)

80 W + 80 W

3)

Surround mode

2)

 (reference) (6 ohms, 1 kHz, 

THD 10%)

RMS output

FRONT:

 

135 W per channel

1)

,  

 

125 W per channel

3)

CENTER:135 W

1)

SURROUND:

 

135 W per channel

1)

,  

 

125 W per channel

3)

SURROUND BACK:

 

135 W

1)

, 125 W

3)

1)

Measured under the following conditions:

2)

Reference power output for front, center, surround 
and surround back speakers. Depending on the 
sound field settings and the source, there may be 
no sound output.

3)

Measured under the following conditions:

 

220 V AC, 50 Hz

Inputs

Analog

Sensitivity: 800 mV/

 

50 kohms

Digital (Coaxial) Impedance: 75 ohms

Outputs (Analog)

AUDIO OUT

Voltage: 800 mV/

 

10 kohms

SUB WOOFER

Voltage: 2 V/1 kohm

Tone

Gain levels

±6 dB, 1 dB step

Reproduction frequency range:

28 – 20,000 Hz

Tuning range

87.5 - 108.0 MHz

Antenna

FM wire antenna

Antenna terminals

75 ohms, unbalanced

Intermediate frequency

10.7 MHz

Tuning range

Models of area code SP, SP6, AUS

With 9-kHz tuning scale:

531 – 1,602 kHz

Models of area code E51

With 10-kHz tuning scale:

530 – 1,610 kHz

4)

With 9-kHz tuning scale: 

531 – 1,602 kHz

4)

Models of area code AR

With 10-kHz tuning scale:

530 – 1,610 kHz

Antenna

Loop antenna

Intermediate frequency

 

450 kHz

SP, SP6, AR

230 V AC, 50 Hz

AUS, E51

240 V AC, 50 Hz

2

• Never reuse a disconnected chip component.

• Notice that the minus side of a tantalum capacitor may be

damaged by heat.

Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with

the lead free mark due to their particular size)

Unleaded solder has the following characteristics.

• Unleaded solder melts at a temperature about 40 °C higher

than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 

°C.

Caution: The printed pattern (copper foil) may peel away if

the heated tip is applied for too long, so be careful!

• Strong viscosity

Unleaded solder is more viscou-s (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.

• Usable with ordinary solder

It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.

0

0

The area code of the receiver you purchased is 
shown on the lower right portion of the rear panel 
(see the illustration below).

Any differences in operation, according to the area 
code, are clearly indicated in the text, for example, 
“Models of area code AA only”.

SURROUND

CENTER

SURROUND BACK

Area code

Inputs/Outputs

Video:

1 Vp-p, 75 ohms

COMPONENT VIDEO:

Y: 1 Vp-p, 75 ohms

P

B

/C

B

: 0.7 Vp-p, 75 ohms

P

R

/C

R

: 0.7 Vp-p, 75 ohms

80 MHz HD Pass Through

Power requirements

(Models of area code SP, SP6, AUS only)

 

 

Power output (DIGITAL MEDIA PORT)

DC OUT: 

5V, 700 mA

Power consumption

Power consumption (during standby mode)

0.3 W

Dimensions (width/height/depth) (Approx.)

430 

× 157.5 × 310 mm 

including projecting parts 
and controls

Mass (Approx.)

7.6 kg

SP, SP6

230 – 240 V AC, 50/60 Hz

AUS

240 V AC, 50 Hz

AR

220 – 230 V AC, 50/60 Hz

E51

120/220/240 V AC,

 

50/60 Hz

SP, SP6, AUS, E51, AR 

 

200 W

4)

You can change the AM tuning scale to 9 kHz or 
10 kHz. After tuning in any AM station, turn off 
the receiver. While holding down TUNING 
MODE, press ?/1. All preset stations will be 
erased when you change the tuning scale. To reset 
the scale to 10 kHz (or 9 kHz), repeat the 
procedure.

Design and specifications are subject to 
change without notice.

•

Abbreviation
AR

: Argentine model

AUS : Australian model
E51 : Chilean and Peruvian models
SP

: Singapore model

SP6 : Singapore and Malaysia models

Parts No.

SP, SP6 models

2-897-029-1

[]

AUS model

2-897-029-2

[]

E51 model

2-897-029-3

[]

AR model

2-897-029-4

[]

3

...................................................................

4

............................................................... 10

............................. 12

................................................................. 13

4-1.

Block Diagram – MAIN Section – .................................. 14

4-2.

Block Diagram – DISPLAY/POWER Section – ............. 15

4-3.

Printed Wiring Board  – DIGITAL Board (Side A) – ...... 16

4-4.

Printed Wiring Board  – DIGITAL Board (Side B) – ...... 17

4-5.

Schematic Diagram  – DIGITAL Board (1/5) – .............. 18

4-6.

Schematic Diagram  – DIGITAL Board (2/5) – .............. 19

4-7.

Schematic Diagram  – DIGITAL Board (3/5) – .............. 20

4-8.

Schematic Diagram  – DIGITAL Board (4/5) – .............. 21

4-9.

Schematic Diagram  – DIGITAL Board (5/5) – .............. 22

4-10. Printed Wiring Board  – MAIN Board – ......................... 23
4-11. Schematic Diagram  – MAIN Board (1/4) – ................... 24
4-12. Schematic Diagram  – MAIN Board (2/4) – ................... 25
4-13. Schematic Diagram  – MAIN Board (3/4) – ................... 26
4-14. Schematic Diagram  – MAIN Board (4/4) – ................... 27
4-15. Printed Wiring Boards

– DISPLAY Board, POWER KEY Board – .................... 28

4-16. Schematic Diagram

– DISPLAY Board, POWER KEY Board – .................... 29

4-17. Printed Wiring Boards

– STANDBY Board, DCDC Board,
AC Select Board (E51 only) – ......................................... 30

4-18. Schematic Diagram

– STANDBY Board, DCDC Board,
AC Select Board (E51 only) – ......................................... 31

4-19. Printed Wiring Boards

– DCAC Board, VIDEO3 Board – .................................. 32

4-20. Schematic Diagram

– DCAC Board, VIDEO3 Board – .................................. 33

4-21. Printed Wiring Boards

– VIDEO Board, HEADPHONE Board – ....................... 34

4-22. Schematic Diagram

– VIDEO Board, HEADPHONE Board – ....................... 35

4-23. Printed Wiring Board  – HDMI SW Board – .................. 36
4-24. Schematic Diagram  – HDMI SW Board – ..................... 37

5-1.

Front Panel Section ......................................................... 44

5-2.

Chassis Section ................................................................ 45

.................................. 46

4

This section is extracted
from instruction manual.

.

?/1

3

4

8

9

1 2

5

6

7

q;

qa

qj

qs

qg

qh

qd

qf

A

?

1

 

Press to turn the receiver on 
or off (page 28, 36, 37, 54).

B

Press to activate the Auto 
Calibration function (page 
30).

C

The current status of the 
selected component or a list 
of selectable items appears 
here (page 6). 

D

Receives signals from 
remote commander.

E

Press to select information 
displayed on the display 
(page 62).

F

Press to select the input 
mode when the same 
components are connected 
to both digital and analog 
jacks (page 59).

G

Turn to adjust the volume 
level of all speakers at the 
same time (page 33, 34, 36, 
37).

H

Press to mute the sound 
(page 34).

I

Press to adjust the 
brightness of the display.

J

Turn to select the input 
source to playback (page 
34).

K

Press to select a sound field 
(page 49, 51, 54).

L

Press to scan a station (page 
55, 58).

M

Press to select the tuning 
mode (page 55, 58).

N

Press to store a station or 
enter the selection when 
selecting the settings (page 
28, 57).

O

Connects to a camcorder or 
video game (page 25, 34).

P

Connects to the supplied 
optimizer microphone for 
the Auto Calibration 
function (page 29).

Q

Connects to headphones 
(page 69).