Sony STR-DN1030 Service Manual ▷ View online
STR-DN1030
13
SECTION 3
TEST MODE
TUNER AM STEP CHANGE MODE
(US, Canadian, Brazilian and Mexican models)
Either the 9 kHz step or 10 kHz step can be selected for the AM
channel step.
Procedure:
1. Press the [
(US, Canadian, Brazilian and Mexican models)
Either the 9 kHz step or 10 kHz step can be selected for the AM
channel step.
Procedure:
1. Press the [
?/1
] button to turn on the main power.
2. Turn the [INPUT SELECTOR] button to select the “AM
TUNER”.
3. Press the [
?/1
] button to turn off the main power.
4. While pressing the [TUNING MODE] button, press the [
?/1
]
button to turn on the main power.
5. Either the message “AM 9k Step” or “AM10k Step” appears,
select the desired step.
VACUUM FLUORESCENT DISPLAY TEST MODE
All fl uorescent segments are tested.
When this test is activated, all segments light on at the same time,
then each segment lights on one after another.
Procedure:
While depressing the [SPEAKERS] and the [DIMMER] buttons
simultaneously, press the [
All fl uorescent segments are tested.
When this test is activated, all segments light on at the same time,
then each segment lights on one after another.
Procedure:
While depressing the [SPEAKERS] and the [DIMMER] buttons
simultaneously, press the [
?/1
] button to turn on the main power.
1. ALL segments light on.
2. Press the [DISPLAY] control, confi rm display.
3. Press the [DISPLAY] control, confi rm display.
4. Press the [DISPLAY] control, all segments light off.
SOUND FIELD CLEAR MODE
The preset sound fi eld is cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
Procedure:
1. While pressing the [MUSIC] button, press the [
The preset sound fi eld is cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
Procedure:
1. While pressing the [MUSIC] button, press the [
?/1
] button to
turn on the main power.
2. The message “S.F. CLEAR” appears and initialization is per-
formed.
KEY CHECK MODE
Button check.
Procedure:
1. While pressing the [SPEAKERS] and the [INPUT MODE]
Button check.
Procedure:
1. While pressing the [SPEAKERS] and the [INPUT MODE]
buttons, press the [
?/1
] button to turn on the main power.
2. The message “REST 13” appears.
Every pressing of any button other than the [
?/1
] counts down
the buttons. The buttons which are already counted once are
not counted again. When all buttons are pressed “REST 00”
displayed.
not counted again. When all buttons are pressed “REST 00”
displayed.
INITIALIZE MODE
All preset contents are cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
(a) SHIPMENT MODE
Procedure:
1. While pressing the [TUNING MODE] and [DIMMER] but-
All preset contents are cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
(a) SHIPMENT MODE
Procedure:
1. While pressing the [TUNING MODE] and [DIMMER] but-
tons, press the [
?/1
] button to turn on the main power.
2. The message “CLEARING” appears and the memories are re-
set to the default values.
3. When done, the message “CLEARED !” appears, the set will
power off.
(b) ALL CLEAR INITIALIZE
Procedure:
1. While pressing the [TUNING MODE] and [INPUT MODE]
Procedure:
1. While pressing the [TUNING MODE] and [INPUT MODE]
buttons, press the [
?/1
] button to turn on the main power.
2. The message “CLEARING” appears and the memories are
reset to the default values.
3. When done, the message “CLEARED !” appears.
(c) USER INITIALIZE
Procedure:
1. Hold the [
(c) USER INITIALIZE
Procedure:
1. Hold the [
?/1
] for 5 seconds.
2. The message “CLEARING” appears on the display.
3. After a few seconds, “CLEARED !” appears.
3. After a few seconds, “CLEARED !” appears.
SWAP MODE
The signal will be swap to all channel so that all speaker will have
sound output.
Procedure:
1. While pressing the [TUNING MODE] and [MOVIE(HD-
The signal will be swap to all channel so that all speaker will have
sound output.
Procedure:
1. While pressing the [TUNING MODE] and [MOVIE(HD-
D.C.S.)] buttons, press the [
?/1
] button to turn on the main
power.
2. The message “SWAP MODE” appears (No change while dis-
played).
PROTECTOR EVER MODE
This mode switch off the protector to investigate the cause of the
protector.
Procedure:
1. While pressing the [TONE MODE] and [A.F.D.] buttons,
This mode switch off the protector to investigate the cause of the
protector.
Procedure:
1. While pressing the [TONE MODE] and [A.F.D.] buttons,
press the [
?/1
] button to turn on the main power.
2. “PROTEVER” appears and switch off the set.
SOFTWARE VERSION DISPLAY MODE
The software version is displayed.
Procedure:
1. While pressing the [TUNING MODE] and [DISPLAY] but-
The software version is displayed.
Procedure:
1. While pressing the [TUNING MODE] and [DISPLAY] but-
tons, press the [
?/1
] button to turn on the main power.
2. The message “N1 ** Mx.xx” appears. This is main micro-
processor version.
**: destination, x.xx: software version
3. Press the [DISPLAY] button on the remote commander, HDMI
micro-processor version or DSP fi rmware version is changed.
VIDEO micro-processor version “H. Ver x.xx” appears.
DSP
fi rmware version “S. Ver x.xx” appears.
Hudson
II
fi rmware version “F. Ver x.xx” appears.
NETWORK
fi rmware version “N. Ver x.xx” appears.
TUNER
fi rmware version “T.Ver x.xx” appears.
DCAC TEST MODE
Procedure:
1. While pressing the [TONE MODE] and the [MOVIE (HD-
Procedure:
1. While pressing the [TONE MODE] and the [MOVIE (HD-
D.C.S.)] buttons, press the [
?/1
] button to turn on the main
power.
2. The message “SOURCE” or “MIC” appears.
SOURCE: normal mode
MIC: mode that output audio from mic input
SW
LH
RH
S
SL
SR
L
C
R
SBL SB SBR
USB HDMI COAX OPT PARTY ARC
D.L.L.
UPDATE D.RANGE A.P.M. ST AAC
D.C.A.C. EQ RDS NIGHT MEM DTS – HD
DTS – ES
LPCM SP A B
MSTR
MHz
k Hz
dB m
–
SLEEP
HDMIOUT
BLUETOOTH
ZONE 2 3
D + EX
HD
True
LFE
PLII
x z
A + B
NEO: 6
BI AMP
HI RES LBR
SW
SL
SR
L
R
SB
USB HDMI COAX OPT PARTY
D.RANGE A.P.M. ST AAC
DTS – HD
DTS – ES
B
MSTR
MHz
dB m
–
SLEEP
HDMIOUT
BLUETOOTH
3
A + B
NEO: 6
BI AMP
HI RES LBR
LH
RH
S
C
SBL
SBR
ARC
D.L.L.
UPDATE
D.C.A.C. EQ RDS NIGHT MEM
LPCM SP A
k Hz
ZONE 2
D + EX
HD
True
PL
Ver. 1.1
STR-DN1030
14
HISTORY MODE
The state that the set is used is memorized.
Procedure:
1. While pressing the [TONE MODE] and [MUSIC] buttons,
The state that the set is used is memorized.
Procedure:
1. While pressing the [TONE MODE] and [MUSIC] buttons,
press the [
?/1
] button to turn on the power and “HISTORY” is
displayed.
2. Each time the [M]/[m] buttons on the remote commander is
pressed, the item is switched in order as follows.
Items
Display
Protector count
COUNT xx
Total single power on time
SxxxxxHxxM
Sound fi eld
SOUNDFIELD
Input function
FUNCTION
Input mode
INPUT MODE
Digital select
DIG SELECT
Stream information
STREAMINFO
Signal confi guration
CONF xxxxx
Headphones
HEADPH xxx
Volume
VOL xx
Bass
BASS xxxdB
Treble
TREB xxxdB
Level FL/FR
FL/R xxxxxx
Level SL/SR
SL/R xxxxxx
Level CT/SW
C/SW xxxxxx
Level BL/BR
BL/R xxxxxx
Level LH/RH
HL/R xxxxxx
Total power on time
TxxxxxHxxM
Muting
MUTING xxx
Power on counter
(Rebox test mode)
(Rebox test mode)
REBOX xxxx
Protector status
PROT xxxx
Temperature status
TEMP xxxc
VACS step
VACS xx
USB UPDATE TEST MODE
To update Main MCU, Video MCU, DSP serial fl ash and Hudson
II software through USB.
Procedure:
1. Plug in USB device in power off condition.
2. While pressing the [TONE MODE] and the [DISPLAY]
To update Main MCU, Video MCU, DSP serial fl ash and Hudson
II software through USB.
Procedure:
1. Plug in USB device in power off condition.
2. While pressing the [TONE MODE] and the [DISPLAY]
buttons, press the [
?/1
] button to turn on the main power.
3. The message “UPDATING” appears and active standby LED
will blinking.
4. If the updating progress succeed, the active standby LED
will blink once per 0.1 seconds and message “COMPLETE”
appears.
appears.
5. If the updating progress fail, the active standby LED
will blink once per 1 seconds and message “ERROR”
appears.
appears.
USB UPDATE VERSION MODE
Function that displays the version number to check whether SPDIF
update is necessary or not.
Procedure:
1. While pressing [TONE MODE] and [DIMMER] buttons,
Function that displays the version number to check whether SPDIF
update is necessary or not.
Procedure:
1. While pressing [TONE MODE] and [DIMMER] buttons,
press the [
?/1
] button to turn on the main power.
2. The message “VER X.XXX” is displayed after 30 seconds.
“X.XXX” is calculated by adding all fi rmware version.
Example:
(MAIN ver. + DSP ver. + HDMI ver. + FARO ver. + BridgeCo
+ 5)/10 = Displayed version
+ 5)/10 = Displayed version
MAIN = 1.02, DSP = 1.01, HDMI = 1.00, FARO = 1.03,
BridgeCo = 1.01
BridgeCo = 1.01
↓
(1.02 + 1.01 + 1.00 + 1.03 + 1.01 + 5)/10 = 1.007
1.007 = X.XXX
STR-DN1030
15
SECTION 4
ELECTRICAL ADJUSTMENT
VIDEO CALIBRATION ADJUSTMENT
Adjustment to decide the standard of the video input signal.
Note: After replacing D-VIDEO NW board, or after “RESET” of the
special menu mode is executed, perform this adjustment.
1. Adjustment jig
The color pattern generator that can output 100% in NTSC/PAL/
HD color bar signal to the component and the composite at the
same time is necessary for the adjustment.
When there is no color pattern generator, it is possible to substitute
it by the Blu-ray Disc player that can output the component terminal
and the video terminal at the same time (Substitution model name
example: BDP-S350).
However, please do the following signal output confi rmation with
the oscilloscope beforehand when substituting it with the Blu-ray
Disc player.
The color pattern generator that can output 100% in NTSC/PAL/
HD color bar signal to the component and the composite at the
same time is necessary for the adjustment.
When there is no color pattern generator, it is possible to substitute
it by the Blu-ray Disc player that can output the component terminal
and the video terminal at the same time (Substitution model name
example: BDP-S350).
However, please do the following signal output confi rmation with
the oscilloscope beforehand when substituting it with the Blu-ray
Disc player.
2. Video calibration adjustment
2-1. Connection
2-1. Connection
color pattern
generator
or
Blu-ray
Disc player
set
HDMI TV
OUT
AVIDEO board
COMPONENT
COMPONENT
VIDEO
ASSIGNABLE
(INPUT ONLY) SAT/CATV (IN 2) jack
SAT/CATV VIDEO IN jack
2-2. Procedure for color pattern generator
Ensure GUI mode is turned off. Press GUI mode on remote until
GUI OFF is shown on FL display.
1. It connects of step 2-1, and the turn on the main power.
2. “SAT/CATV” is selected by using [INPUT SELECTOR] dial.
3. Input NTSC color bars signal from the color pattern generator.
4. Press the [
Ensure GUI mode is turned off. Press GUI mode on remote until
GUI OFF is shown on FL display.
1. It connects of step 2-1, and the turn on the main power.
2. “SAT/CATV” is selected by using [INPUT SELECTOR] dial.
3. Input NTSC color bars signal from the color pattern generator.
4. Press the [
?/1
] button to turn off the main power.
5. While pressing the [MOVIE(HD-D.C.S.)] and [SPEAKERS]
buttons, press the [
?/1
] button to turn on the main power.
When correctly entering the test mode “FIN _:_:_” and “N:
MWx_ _ _ _ _” are displayed in 1 secound interval (alternating
display).
MWx_ _ _ _ _” are displayed in 1 secound interval (alternating
display).
6. The NTSC signal adjustment is begun when press the cross
(center of cursor) button of remote commander, and the display
changes from “N:MWx_ _ _ _ _” to “N:MWoCDV_ _”
little by little. Finally, “FIN N:_:_” and “N: MWoCDV_ _” are
displayed in 1 second interval (alternating display).
changes from “N:MWx_ _ _ _ _” to “N:MWoCDV_ _”
little by little. Finally, “FIN N:_:_” and “N: MWoCDV_ _” are
displayed in 1 second interval (alternating display).
7. Input PAL color bars signal from the color pattern generator.
8. Perform step 6 to 7 for the PAL signal adjustment.
9. Input HD color bars signal (720p or 1080i) from the color
8. Perform step 6 to 7 for the PAL signal adjustment.
9. Input HD color bars signal (720p or 1080i) from the color
pattern generator.
10. Perform step 6 to 7 for the HD signal adjustment.
11. The turn off the main power.
11. The turn off the main power.
2-3.
Procedure for Blu-ray Disc player
Ensure GUI mode is turned off. Press GUI mode on remote until
GUI OFF is shown on FL display.
1. It connects of step 2-1, and the turn on the main power of set
GUI OFF is shown on FL display.
1. It connects of step 2-1, and the turn on the main power of set
and Blu-ray Disc player.
2. “SAT/CATV” is selected by using [INPUT SELECTOR] dial.
3. Press the OPEN/CLOSE button of the Blu-ray Disc player,
3. Press the OPEN/CLOSE button of the Blu-ray Disc player,
and DVD test disc “HLX-504 (Part No. J-6090-088-A)” or
“HLX- 513 (Part No. J-2501-305-A)” is insert. The disc
playback automatically becomes start “Main Menu” is display.
“HLX- 513 (Part No. J-2501-305-A)” is insert. The disc
playback automatically becomes start “Main Menu” is display.
4. “1.Color Bar 100%” of “1.Video Signal” is reproduced, and
100% in the color bar is displayed in the TV monitor, playing
the Blu-ray Disc player is pause playback.
the Blu-ray Disc player is pause playback.
5. Press the [
?/1
] button to turn off the main power of the set.
6. While pressing the [MOVIE(HD-D.C.S.)] and [SPEAKERS]
buttons, press the [
?/1
] button to turn on the main power of the
set. When correctly entering the test mode “FIN _:_:_” and “N:
MWx_ _ _ _ _” are displayed in 1 secound interval (alternating
display).
MWx_ _ _ _ _” are displayed in 1 secound interval (alternating
display).
7. The NTSC signal adjustment is begun when press the cross
(center of cursor) button of remote commander, and the
display changes from “N:MWx_ _ _ _ _” to “N:MWoCDV_ _”
little by little. Finally, “FIN N:_:_” and “N: MWoCDV_ _” are
displayed in 1 second interval (alternating display).
display changes from “N:MWx_ _ _ _ _” to “N:MWoCDV_ _”
little by little. Finally, “FIN N:_:_” and “N: MWoCDV_ _” are
displayed in 1 second interval (alternating display).
8. Press the OPEN/CLOSE button of the Blu-ray Disc player, and
change to DVD test disc “HLX-506 (Part No. J-6090-077-A)”
or “HLX-507 (Part No. J-6090-078-A)”. The disc playback
automatically becomes start “Main Menu” is display.
or “HLX-507 (Part No. J-6090-078-A)”. The disc playback
automatically becomes start “Main Menu” is display.
9. “1.Color Bar 100%” of “1.Video Signal” is reproduced, and
100% in the color bar is displayed in the TV monitor, playing
the Blu-ray Disc player is pause playback.
the Blu-ray Disc player is pause playback.
10. The PAL signal adjustment is begun when press the cross
(center of cursor) button of remote commander. Finally, “FIN
N:P:_” and “P:MWoCDV_ _” are displayed in 1 second inter-
val (alternating display).
N:P:_” and “P:MWoCDV_ _” are displayed in 1 second inter-
val (alternating display).
11. Press the OPEN/CLOSE button of the Blu-ray Disc player, and
change to DVD test disc “HLX-104 (Part No. J-6090-199-A)”.
The disc playback automatically becomes start “Main Menu”
is display.
The disc playback automatically becomes start “Main Menu”
is display.
12. “59.94Hz, 1080i” → “1.Video Signal” → “1.Color Bar 100%”
is selected, and 100% in the color bar is displayed in the TV
monitor, playing the Blu-ray Disc player is pause playback.
monitor, playing the Blu-ray Disc player is pause playback.
13. The video output of the Blu-ray Disc player is switched 1080i
(The output from the component terminal of the Blu-ray Disc
player becomes 1080i output).
player becomes 1080i output).
14. The HD signal adjustment is begun when press the cross
(center of cursor) button of remote commander. Finally, the
display returns to the display of “FIN N:P:H”.
display returns to the display of “FIN N:P:H”.
15. The turn off the main power.
FM AUTO STOP CHECK
signal
generator
set
Procedure:
1. Turn on the set.
2. Input the following signal from signal generator to FM antenna
1. Turn on the set.
2. Input the following signal from signal generator to FM antenna
input directly.
Carrier frequency : A = 87.5 MHz, B = 98 MHz, C = 108 MHz
Deviation
Deviation
: 75 kHz
Modulation
: 1 kHz
ANT input
: 35 dBu (EMF)
Note: Use 75 ohm coaxial cable to connect signal generator and the set.
You cannot use video cable for checking.
Use signal generator whose output impedance is 75 ohm.
3. Set to FM tuner function and scan the input FM signal with
automatic scanning.
4. Confi rm that input frequency of A, B and C are detected and
automatic scanning stops.
When the station signal is received in good condition, automatic
scanning stops.
scanning stops.
STR-DN1030
16
SECTION 5
DIAGRAMS
• Circuit Boards Location
STANDBY board
V-SELECT board
(Brazilian model)
(Brazilian model)
MX AC board
(Mexican model)
DCDC board
THERMAL board
POWERKEY board
HP board
BLUETOOH MODULE
(US, Canadian, Mexican and Brazilian models)
(US, Canadian, Mexican and Brazilian models)
BT INTERFACE board
(US, Canadian, Mexican and Brazilian models)
(US, Canadian, Mexican and Brazilian models)
USB board
DISPLAY board
MAIN board
AVIDEO board
NETWORK board
D-VIDEO NW board
TUNER1 board
GND BRACKET board
DIGITAL board
Ver. 1.2
Click on the first or last page to see other STR-DN1030 service manuals if exist.