Sony STR-DH510 Service Manual ▷ View online
STR-DH510
5
SECTION 1
DISASSEMBLY
Note: This set can be disassemble according to the following sequence.
1-4. DIGITAL BOARD
(Page 7)
1-5. MAIN BOARD SECTION
(Page 7)
1-1. CASE
(Page 5)
1-2. BACK PANEL SECTION
(Page 6)
1-3. FRONT PANEL SECTION
(Page 6)
SET
Note: Follow the disassembly procedure in the numerical order given.
1-1. CASE
1 two screws
3 two screws
(+BVTP 3
u 8)
4 case
2 two screws
(for Canadian model only)
STR-DH510
6
1-2. BACK PANEL SECTION
1-3. FRONT PANEL SECTION
Ver. 1.2
• Abbreviation
ECE : Continental European,
ECE : Continental European,
East European and Russian models
4 CNP902 (2P)
2 CN906 (4P)
3 CN907 (3P)
5 CNS203 (6P)
6 wire (flat type)
(CN2201 (9 core)) (US, Canadian)
(CN2211 (11 core)) (UK, ECE,
(CN2211 (11 core)) (UK, ECE,
Australian)
7 wire (flat type) (19 core)
(CN2601)
8 CNS271 (17P)
9 five screws
(+BVTP 3
u 8)
0 six screws
(+BVTP 3
u 8)
qa three screws
(+BVTP 3
u 8)
1 CNP901 (2P)
(for Canadian model only)
1 CNP792 (4P)
3 five screws
(+BVTP 3
u 8)
4 front panel section
wire (flat type) (15 core)
(CN2106)
(CN2106)
5 sheet, insulation
(for Canadian model only)
6 cushion, saranet
STR-DH510
7
1-4. DIGITAL BOARD
1-5. MAIN BOARD SECTION
CNP410 (15P)
CNP412 (18P)
2
1 CN2501 (4P)
DIGITAL board
3 TEMP-SENSOR board
3 CNP920 (5P)
4 two screws
(+BVTP 3 x 8 )
5 two screws
(+BVTP 3 x 8)
6 MAIN board section
2 CONNECTION board
1 CNS170 (6P)
STR-DH510
8
SECTION 2
TEST MODE
AM CHANNEL STEP 9 kHz/10 kHz SELECTION MODE
(US, Canadian model only)
* Either the 9 kHz step or 10 kHz step can be selected for the AM
(US, Canadian model only)
* Either the 9 kHz step or 10 kHz step can be selected for the AM
channel step.
* Procedure:
Turn the [INPUT SELECTOR] control to set AM and press the
[
[
?/1
] button to turn off the main power.
1. While depressing the [TUNING MODE] button, press the
[
?/1
] button to turn on the main power.
2. Either the message “9K STEP” or “10K STEP” appears for a
moment and select the desired step.
VACUUM FLUORESCENT DISPLAY TEST MODE
* All fluorescent segments are tested.
When this test is activated, all segments light on at the same time,
then each segment lights on one after another.
then each segment lights on one after another.
* Procedure:
While depressing the [TUNING +] and the [DIMMER] buttons
simultaneously, press the [
simultaneously, press the [
?/1
] button to turn on the main pow-
er.
1. ALL segments light on.
L
C
R
SL
S
SR
SBL SB SBR
LH
RH
SW
COAX
OPT
HDMI
LFE
DTS -ES
NEO:6 S-AIR
96/24
DTS-HD MSTR HI RES
LBR
LPCM
RDS
AAC
TrueHD
SLEEP
D.RANGE
ST
D
PL II
+ EX
MHz
ft.
k Hz m
x z
dB
2. Press the [DISPLAY] button, confirm display.
L
C
R
SL
S
SR
SBL SB SBR
LH
RH
SW
COAX
OPT
HDMI
LFE
DTS -ES
NEO:6 S-AIR
96/24
DTS-HD MSTR HI RES
LBR
LPCM
RDS
AAC
TrueHD
SLEEP
D.RANGE
ST
D
PL II
+
EX
MHz
ft.
k
Hz
m
x
z
dB
3. Press the [DISPLAY] button, confirm display.
L
C
R
SL
S
SR
SBL SB SBR
LH
RH
SW
COAX
OPT
HDMI
LFE
DTS -ES
NEO:6 S-AIR
96/24
DTS-HD MSTR HI RES
LBR
LPCM
RDS
AAC
TrueHD
SLEEP
D.RANGE
ST
D
PL II
+
EX
MHz
ft.
k
Hz
m
x
z
dB
4. Press the [DISPLAY] button, all segments light off.
SOUND FIELD CLEAR MODE
* The preset sound field is cleared when this mode is activated.
* The preset sound field is cleared when this mode is activated.
Use this mode before returning the product to clients upon com-
pletion of repair.
pletion of repair.
* Procedure:
1. While depressing the [MUSIC] button, press the [
1. While depressing the [MUSIC] button, press the [
?/1
] button
to turn on the main power.
2. The message “S.F. CLEAR” appears for a moment and initial-
ization is performed.
SOFTWARE VERSION CHECK MODE
* The software version is displayed.
* Procedure:
1. While depressing the [TUNING MODE] and the [DISPLAY]
* The software version is displayed.
* Procedure:
1. While depressing the [TUNING MODE] and the [DISPLAY]
buttons simultaneously, press the [
?/1
] button to turn on the
main power.
2. The model name, destination and the software version are
displayed for a moment.
KEY CHECK MODE
* Button check
* Procedure:
1. While depressing the [TUNING +] and the [MUTING] but-
* Button check
* Procedure:
1. While depressing the [TUNING +] and the [MUTING] but-
tons simultaneously, press the [
?/1
] button to turn on the main
power.
2. The message “REST 12” appears.
3. Every pressing of any button other than the [
3. Every pressing of any button other than the [
?/1
] counts down
the buttons. The buttons which are already counted once are
not counted again. When all buttons are pressed “REST 00”
appears.
not counted again. When all buttons are pressed “REST 00”
appears.
SWAP ALL MODE
* The signal will be swap to all channel so that all speaker will
* The signal will be swap to all channel so that all speaker will
have sound output.
* Procedure:
1. While depressing the [TUNING MODE] and the [MOVIE]
1. While depressing the [TUNING MODE] and the [MOVIE]
buttons simultaneously, press the power [
?/1
] button to turn
on the main power.
2. “SWAP.MODE” appears. (No change while displayed.)
SHIPMENT MODE
* All preset contents are reset to the default setting.
* Procedure:
1. While depressing the [TUNING MODE] and the [DIMMER]
* All preset contents are reset to the default setting.
* Procedure:
1. While depressing the [TUNING MODE] and the [DIMMER]
buttons simultaneously, press the power [
?/1
] button to turn
on the main power.
2. The message “CLEARING” appears.
3. After a few seconds, “CLEARED” appears and switch off the
3. After a few seconds, “CLEARED” appears and switch off the
set.
PROTECTOR AUTO OFF
* To disable auto off after protector occur.
* Procedure:
1. While depressing the [INPUT MODE] and the [A.F.D.] but-
* To disable auto off after protector occur.
* Procedure:
1. While depressing the [INPUT MODE] and the [A.F.D.] but-
tons simultaneously, press the power [
?/1
] button to turn on
the main power.
2. “PROTECT” appears.
Click on the first or last page to see other STR-DH510 service manuals if exist.