DOWNLOAD Sony STR-DG720 Service Manual ↓ Size: 4.19 MB | Pages: 92 in PDF or view online for FREE

× 8)

AM CHANNEL STEP 9 kHz/10 kHz SELECTION MODE
(US, Canadian model only)
* Either the 9 kHz step or 10 kHz step can be selected for the AM 

channel step.

* Procedure:

Turn the [INPUT SELECTOR] control to set AM and press the 
[

?/1

] button to turn off the main power.

While depressing the [TUNING MODE] button, press the [

?/1

] 

button to turn on the main power.
Either the message “9k STEP” or “10k STEP” appears for a mo-
ment and select the desired step.

VACUUM FLUORESCENT DISPLAY TEST MODE
* All fl uorescent segments are tested.

When this test is activated, all segments light on at the same time, 
then each segment lights on one after another.

* Procedure:

While depressing the [TUNING MODE] and the [DISPLAY] 
buttons simultaneously, press the [

?/1

] button to turn on the 

main power.

1.  ALL segments light on.

2.  Turn the [INPUT SELECTOR] control, confi rm display.

3.  Turn the [INPUT SELECTOR] control, confi rm display.

4.  Turn the [INPUT SELECTOR] control, all segments light off.

SOUND FIELD CLEAR MODE
* The preset sound fi eld is cleared when this mode is activated.

Use this mode before returning the product to clients upon com-
pletion of repair.

* Procedure:

While depressing the [2CH] button, press the [

?/1

] button to turn 

on the main power.
The message “S.F. CLR.” appears for a moment and initialization 
is performed.

SOFTWARE VERSION DISPLAY MODE
* The software version is displayed.
* Procedure:

While depressing the [SPEAKERS (OFF/A/B)] and the [DIS-
PLAY] buttons simultaneously, press the [

?/1

] button to turn on 

the main power.
The model name, destination and the software version are dis-
played for a moment.

KEY CHECK MODE
* Button check
* Procedure:

While depressing the [SPEAKERS (OFF/A/B)] and the [2CH] 
buttons simultaneously, press the [

?/1

] button to turn on the 

main power.
Either the message “REST 14” appears.
Every pressing of any button other than the [

?/1

] counts down 

the buttons. The buttons which are already counted once are not 
counted again. When all buttons are pressed “REST 00” ap-
pears.

SWAP ALL MODE
* When this mode is used, output the audio signal of front L/R 

channel to all channel.

* Procedure:
1.  While pressing the [MEMORY/ENTER] and [DISPLAY] but-

tons, press the [

?/1

] button to turn on the main power.

2.  The message “DSP TEST” appears.
3.  Press the [AMP MENU] button on the remote commander, and 

the message “9_DSPTST” appears.

4.  Press the [

b] button on the remote commander to enter the 

DSP test mode menu.

5.  Press the [

v] button on the remote commander twice to enter 

the swap mode, and the message “SWP.AUTO” appears.

6.  Press the [

b] button on the remote commander twice to select 

“SWP.

[]

ALL”.

SHIPMENT MODE
* All preset contents are reset to the default setting.
* Procedure:
1.  While depressing the [SPEAKERS (OFF/A/B)] and the [MU-

SIC] buttons simultaneously, press the power [

?/1

] button to 

turn on the main power.

2.  “CLEARED” appears and switch off the set.

RE-BOX CLASSIFICATION TEST MODE
* Procedure:
1.  While pressing the [MEMORY/ENTER] and the [INPUT 

MODE] buttons simultaneously, press the power [

?/1

] button 

to turn on the main power.

2. “R.BOX

[][][]

xxx” appears.

3.  xx indicates number of times set powered on.
4.  Press any button or power off the set to release test mode.

MEMORY

MEMORY

DCAC FACTORY TEST MODE
DCAC Factory Test mode have two stages:
1.  DCAC DSP Data Line Checking
2.  DCAC board Checking

Factory Test System Setup

1.  When power off:
 

Press the three buttons [MEMORY/ENTER] + [MOVIE] +  
[

?/1

].

 “DCAC

[]

FTM” appears.

 

Afterward, press the [TUNING MODE] to start DCAC factory 
test mode.

1. DCAC DSP Data Line Checking
After press the [TUNING MODE], DCAC Factory test mode will 
start, below display will show:
“DCAC

[][][]

x” 

x=1, 2, 3, 4

If there is error happen, below display will show:

“ERR

[]

SD0x” x=1 

t D1501 or R1530 problem

 x=2 

t D1502 problem

 x=3 

t D1503 problem

 x=4 

t D1504 problem

2. DCAC board Checking
Connect front left speaker of the receiver and AUTO CAL micro-
phone. Turn [MASTER VOLUME] jog, there will be test tone 
sound output from front left speaker, and the display will change 
accordingly.

“AD

[]

-

[]

xxx” 

xxx=0 to 255 (depends on loudness of test tone)

Procedure:
1.  Turn on the set.
2.  Input the following signal from Signal Generator to FM 

antenna input directly.

* Carrier Frequency: A=87.5 MHz, B=98 MHz, C=108 MHz
Deviation 

: 75 kHz

Modulation  : 1 kHz
ANT input 

: 35 dBu (EMF)

Note:
Please use 75 ohm “coaxial cable” to connect SG and the set. You 
cannot use video cable for checking.
Please use SG whose output impedance is 75 ohm.

3.  Set to FM tuner function and scan the input FM signal with 

automatic scanning.

4. Confi rm that input Frequency of A, B and C are detected and 

automatic scanning stops.

The stop of automatic scanning means “The station signal is re-
ceived in good condition.”