Sony STR-DE135 Service Manual ▷ View online
– 25 –
5-7.
SCHEMATIC DIAGRAM – MAIN Board (2/2)/SPK SWITCH Board/SECONDARY Board/
PRIMARY Board/STANDBY TRANS Board –
PRIMARY Board/STANDBY TRANS Board –
STR-DE135
R742
1.2k 1/2W
R792
1.2k 1/2W
(Page 14)
(Page 14)
(Page 14)
The components identified by mark
!
or dotted
line with mark
!
are critical for safety.
Replace only with part number specified.
– 26 –
5-8.
IC PIN FUNCTION DESCRIPTION
•
DISPLAY BOARD IC201
µ
PD78044FGF-115-3B9 (SYSTEM CONTROLLER, FL DRIVER)
Pin No.
Pin Name
I/O
Description
1 to 7
DIG7 to DIG1
O
Digit drive signal output to the fluorescent indicator tube (FL201)
8
VDD
—
Power supply terminal (+5V)
9
S.CLK
O
Serial data transfer clock signal output to the LC78212 (IC401), PLL IC on FM/AM tuner pack
“L” active
“L” active
10
S.DATA
O
Serial data output to the LC78212 (IC401), PLL IC on FM/AM tuner pack “L” active
11
PLL.DATA
I
Serial data input from the PLL IC on FM/AM tuner pack “L” active
12
S.CE (LC7822)
O
Serial chip enable signal output to the LC78212 (IC401), PLL IC on FM/AM tuner pack
“H” active
“H” active
13
S.CE (LV1010)
O
Serial chip enable signal output terminal “L” active Not used (pull down)
14
REAR-RY
O
Relay drive signal output for the rear side speaker “H”: relay on Not used (open)
15
BRIDGE
O
Bridgeable relay drive signal output terminal “H”: relay on Not used (open)
16
PROTECT
I
Over load detect signal input from the protect circuit “L”: protect detect
17
RESET
I
System reset signal input from the reset signal generator (IC950, Q201) “L”: reset
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
18
AUTO-STOP
I
Tuned display detection signal input from the FM/AM tuner pack “L”: tuned
19
STEREO-IN
I
Stereo detection signal input from the FM/AM tuner pack “L”: stereo
20
AVSS
—
Ground terminal (for A/D converter analog system)
21
SP-RY
O
Relay drive signal output for the speaker protect “H”: relay on
22
SURR-RY
O
Relay drive signal output for the surround speaker “H”: relay on Not used (pull down)
23
POWER-RY
O
Relay drive signal output for the power on/off control “H”: relay on
24
SIGNAL
I
FM and AM signal meter voltage detection signal input from the FM/AM tuner pack
25
A/D-4
I
Key input terminal (A/D input) S210 (NAME) key input
(Used for the AEP and UK models only)
(Used for the AEP and UK models only)
26
A/D-3
I
Key input terminal (A/D input) S231 to S239 (BASS BOOST, MUTING, SHIFT, 0, MEMORY
or MEMORY/ENTER, CD, MD/TAPE, TV/SAT or TV/LD, RDS PTY) keys input
(S239 RDS PTY key: used for the AEP and UK models only)
or MEMORY/ENTER, CD, MD/TAPE, TV/SAT or TV/LD, RDS PTY) keys input
(S239 RDS PTY key: used for the AEP and UK models only)
27
A/D-2
I
Key input terminal (A/D input) S221 to S230 (FM or FM/AM, 6, 5, 4, 7, 8, 9, FM MODE,
VIDEO, TUNER) keys input
VIDEO, TUNER) keys input
28
A/D-1
I
Key input terminal (A/D input) S211 to S220 (DISPLAY, AM or RDS EON, 3, 2, 1, TUNING
or TUNING/CHAR –/+, PRESET TUNING or PRESET/PTY SELECT –/+, DIRECT) keys input
(S211 DISPLAY key: used for the AEP and UK models only)
or TUNING/CHAR –/+, PRESET TUNING or PRESET/PTY SELECT –/+, DIRECT) keys input
(S211 DISPLAY key: used for the AEP and UK models only)
29
AVDD
—
Power supply terminal (+5V) (for A/D converter analog system)
30
AVREF
I
Reference voltage (+5V) input terminal (for A/D converter)
31
RDS DATA IN
I
RDS data input from the RDS decoder (IC1) (Used for the AEP and UK models only)
32
OPEN
—
Not used (open)
33
GND
—
Ground terminal
34
X1
I
Main system clock input terminal (4.19 MHz)
35
X2
O
Main system clock output terminal (4.19 MHz)
36
WOFER RLY
O
Relay drive signal output for the woofer speaker “H”: relay on Not used (open)
37
LED SELECT
O
LED select signal output terminal “H” active Not used (open)
38
DOLBY LED
O
LED drive signal output terminal “H”: LED on Not used (open)
39
C STUDIO LED
O
LED drive signal output terminal “H”: LED on Not used (open)
40
HALL LED
O
LED drive signal output terminal “H”: LED on Not used (open)
41
ENTER LED
I
Not used (fixed at “L”)
42
VOL DOWN
O
Motor drive signal (volume down direction) output to the volume motor drive (IC202)
“H” active
“H” active
43
VOL UP
O
Motor drive signal (volume up direction) output to the volume motor drive (IC202)
“H” active
“H” active
– 27 –
Pin No.
Pin Name
I/O
Description
44
SYS-POWER
I
Power on/off switch (S240 I/
u) input terminal “L” is input when key pressing
45
TUNER MUTE
O
Muting control signal output to the FM/AM tuner pack “H”: muting on
46
RDS CLK IN
I
RDS serial clock signal input from the RDS decoder (IC1)
(Used for the AEP and UK models only)
(Used for the AEP and UK models only)
47
STOP
I
Power down detection signal input from the reset signal generator (IC950)
“L”: power down, normally: “H”
“L”: power down, normally: “H”
48
VSS
—
Ground terminal
49
SIRCS
I
Sircs remote control signal input from the remote control receiver (IC203)
50
MUTING LED
O
LED drive signal output of the MUTING indicator (D211) “L”: LED on
51
5.1 LED
O
LED drive signal output terminal “L”: LED on Not used (open)
52
VDD
—
Power supply terminal (+5V)
53
LOW BOOST
O
Control signal output of the BASS BOOST circuit and LED drive signal output of the BASS
BOOST indicator (D212) “H”: BASS BOOST on (LED on)
BOOST indicator (D212) “H”: BASS BOOST on (LED on)
54
FUNC. MUTE
O
Audio line muting on/off control signal output terminal “H”: muting on
55
IC. MUTE
O
Muting on/off control signal output terminal “H”: muting on Not used (open)
56
VERSION
I
Setting terminal for the version
57, 58
S2, S1
O
Not used (open)
59 to 61
LED1 to LED3
O
LED drive signal output terminal “H”: LED on Not used (open)
62 to 70
S15 to S7
O
Segment drive signal output to the fluorescent indicator tube (FL201)
71
VLOAD
—
Negative power supply terminal for the fluorescent indicator tube drive (–24V)
72 to 77
S6 to S1
O
Segment drive signal output to the fluorescent indicator tube (FL201)
78 to 80
DIG10 to DIG8
O
Digit drive signal output to the fluorescent indicator tube (FL201)
– 28 –
(1)
CASE SECTION
SECTION 6
EXPLODED VIEWS
The components identified by
mark
mark
! or dotted line with mark
! are critical for safety.
Replace only with part number
specified.
specified.
• Items marked “*” are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering
these items.
delay should be anticipated when ordering
these items.
• The mechanical parts with no reference num-
ber in the exploded views are not supplied.
• Hardware (# mark) list and accessories and
packing materials are given in the last of the
electrical parts list.
electrical parts list.
NOTE:
• -XX and -X mean standardized parts, so they
may have some difference from the original
one.
one.
• Color Indication of Appearance Parts
Example:
KNOB, BALANCE (WHITE) . . . (RED)
KNOB, BALANCE (WHITE) . . . (RED)
↑
↑
Parts Color Cabinet's Color
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Description
Remark
1
X-4947-207-1 FOOT ASSY (F50150S) (AEP, UK)
1
X-4947-208-1 FOOT ASSY (F50150S) (US)
2
3-710-901-11 SCREW, TAPPING
* 3
4-998-206-21 CASE (413226)
2
2
3
2
1
1
#1
#1
#1
#1
Front panel
section
section
not supplied
not
supplied
supplied
not supplied
not
supplied
supplied
Chassis section
Click on the first or last page to see other STR-DE135 service manuals if exist.