Sony STR-DA5000ES Service Manual ▷ View online
5
STR-DA5000ES
SECTION 1
SERVICING NOTES
• MODEL IDENTIFICATION
– Back Panel –
PART No.
Model
PART No.
US model
4-246-511-0
[]
Canadian model
4-246-511-1
[]
AEP model
4-246-511-2
[]
Chinese model
4-246-511-4
[]
Taiwan model
4-246-511-6
[]
Ver 1.1
ERROR MESSAGES
If there is a malfunction, the display shows a code of two numbers and a message. You can check the condition of the system by message.
Refer to the following table to solve the problem.
Refer to the following table to solve the problem.
messages
check code
cause and response
DECODE ERROR
01
Appears when the signal which the receiver can not decode
(example DSD-CD) is input when “DEC. PRI.” in the CUSTOM
IZE menu is set to “PCM”. Set to “AUTO”.
(example DSD-CD) is input when “DEC. PRI.” in the CUSTOM
IZE menu is set to “PCM”. Set to “AUTO”.
PROTECTOR
11
Irregular current output to the speakers. Turn off the receiver and
check the speaker connection. Then turn on the power again. Be
comes this display, When short current flowed with breakage of
the power MOS, or when detection resistor becomes open in
connection with it.
check the speaker connection. Then turn on the power again. Be
comes this display, When short current flowed with breakage of
the power MOS, or when detection resistor becomes open in
connection with it.
PROTECTOR
12
The amplifier section is overheated. Turn off the receiver and
check that the ventilation hole is not covered. Leave the receiver
for a while and turn on the power again.
check that the ventilation hole is not covered. Leave the receiver
for a while and turn on the power again.
PROTECTOR
13
The power supply section is overheated. Turn off the receiver and
check that the ventilation hole is not covered. leave the receiver
for a while and turn on the power again.
check that the ventilation hole is not covered. leave the receiver
for a while and turn on the power again.
PROTECTOR
21
DC between speaker terminal is detected (abnomalities such as
DSD 0DATA and signal clip can be considered). Turn off the
receiver and check the speaker connection. Then turn on the power
again.
DSD 0DATA and signal clip can be considered). Turn off the
receiver and check the speaker connection. Then turn on the power
again.
PROTECTOR
22
Two defects a e considered, when current detection of a switching
power supply operated by the super fluous speaker, +B power
supply shut down or when the power MOS broke and +B line
short. Turn off the receiver and check the speaker connection.
Then turn on the power again.
power supply operated by the super fluous speaker, +B power
supply shut down or when the power MOS broke and +B line
short. Turn off the receiver and check the speaker connection.
Then turn on the power again.
6
STR-DA5000ES
Note:
Follow the disassembly procedure in the numerical order given.
D-AMP BOARD, REG BOARD SERVICE POSITION
– BOTTOM VIEW –
1
four screws
(BVTP3
(BVTP3
×
8)
1
six screws
(BVTP3
(BVTP3
×
8)
1
four screws
(BVTP3
(BVTP3
×
8)
1
three screws
(BVTP3
(BVTP3
×
8)
2
bottom plate
REG board
D-AMP board
7
STR-DA5000ES
CIS BOARD (US, Canadian models), S-VIDEO BOARD SERVICE POSITION
VIDEO BOARD SERVICE POSITION
S-video board
CIS board
(US, Canadian models)
(US, Canadian models)
insulator
video board
insulator
8
STR-DA5000ES
AUDIO BOARD SERVICE POSITION
SWITCHING REGULATOR SERVICE POSITION
audio board
insulator
switching regulator
Click on the first or last page to see other STR-DA5000ES service manuals if exist.