DOWNLOAD Sony STR-DA3ES / STR-DA5ES / STR-VA555ES Service Manual ↓ Size: 8.19 MB | Pages: 81 in PDF or view online for FREE

7

Track No.

1
2

3
4
5

• Required Instrument
CD player (equipped with optical digital output)
Optical cable
DTS test CD (J-2501-154-A)

Time

5'40"
4'16"

4'08"
3'29"
6'42"

Music Demonstration

Contents

Seal : "Prayer for the Dying"
Andrew Litton conducting
The Dallas Symphony Orchestra & Chorus:
Excerpt from Tchaikovsky: "1812 Overture"
Alan Parsons with Christopher Cross: "So Far Away"
Shoelss Joe: "The Bet"
TELARC: "A Touch of Surround Madness"

Procedure:
1. Set the FUNCTION of the receiver to the CD position and con-

firm that " [OPTICAL] " and "CD" appear on the display.

2. Insert the DTS test CD into the CD player and play the CD.

3. About three seconds later, confirm that the receiver recognizes

the optical signal and that the "DTS" and "dts [3/2]" are appear
on the display.  Confirm also that MULTI CHANNEL DECOD-
ING (blue lamp) flashes on the front panel.

Track No.

6

7

8
9

10
11
12
13
14
15

16

Set-Up

Contents

1 kHz sine (All channels)
Level Adjustment and Harmonic Distortion Analysis
100 Hz sine (All channels)
Verification of Signal and Subwoofer Testing
C-Weighted Pink Noise-Left Front Channel
C-Weighted Pink Noise-Center Channel
C-Weighted Pink Noise-Right Front Channel
C-Weighted Pink Noise-Right Rear Channel
C-Weighted Pink Noise-Left Rear Channel
C-Weighted Pink Noise-Subwoofer (LEE)
C-Weighted Pink Noise-All Channels
10 Hz to 20 kHz Sine Sweep
An "All Channel" Frequency Response Test
20 Hz to 160 Hz sine sweep
A "Subwoofer" Low Frequency Response Test

* Track numbers from 8 to 14 are for Room Equalization and Channel Iden-

tification.

1

 CD player

2

 Optical

     digital output

3

 Optical input

4

 Receiver  STR-DA3ES/DA5ES/VA555ES

5

 DTS test CD (Music Demonstration and Set Up Disc)

Time

1'00"

1'00"

1'00"
2'00"
2'00"
2'00"
2'00"
2'00"
2'00"
2'00"

  2'00"

C803

D801

D802

C804

(CHASSIS)

330

Ω 

2W

 Be careful about an electrical shock caused by remains of electrical potential.

            The following parts on DC board have the +B or -B electrical potential.

Heat sink for rectifier diodes D801, 802
Aluminium case of smoothing capacitor C803, 804

           The 40-60V electrical voltage remains in C803, 804 when the power turns off.
           Be sure to discharge in the following manner before servicing.

           Discharging
              1. Pull out the power cord from the wall outlet.
              2. Connect 330 ohm 2W resistors between the heat
                  sinks for D801 and 802 and chassis individually.
              3. Check the electrical potential drops fully, then start
                  servicing.

8

This section is extracted from
instruction manual.

1 23 4 56

7

8 9 q;

rf rd

rs

ra

r;

el

eg ed ea

ej

wj

ek eh ef es e;

wl wk

wh wgwf wd qswa

qaqsqd

qf

qgqhqj

qkql

w;

2CH qg
2ND ROOM (STR-DA3ES, VA555ES only)
eh

2ND/3RD ROOM (STR-DA5ES
only) eh
6.1CH indicator ql
6.1CH DECODING qk
A.F.D. q;
AUDIO SPLIT wf
CINEMA STUDIO EX qa
Cursor buttons (

 I/i ) wk

Digital Cinema Sound indicator
qh

DIGITAL CONCERT HALL qd
DIMMER rs
Display 9
DISPLAY4
DOOR OPEN wg
ENTER wj
EQ ea
EQUALIZER eg
FM/AM 7
FM MODE r;
FUNCTION wd
INPUT MODE ws
IR emitter (STR-DA5ES, VA555ES only) 3
IR receptor 2
Jog dial wl
LEVEL e;
MASTER VOLUME w;
MEMORY el
MODE +/– qf
MULTI/2CH ANALOG DIRECT
qj

MULTI CHANNEL DECODING
indicator qs
MUTING qs
NAME wa
NIGHT MODE 6

NIGHT MODE indicator 5
ON SCREEN ef
PHONES jack rf
PRESET TUNING +/– 8
PTY SELECT +/– (Models of
area code AEP only) ek
RDS/PTY (Models of area code
AEP only) ej
SET UP wh
SLEEP ej
SPEAKERS switch rd
SURROUND es
TUNING +/– ek
VIDEO 3 INPUT jacks ra
?/1 (power) 1 (18, 24, 38)

9

+

–

+

–

+

–

4 8 

IN

IN

OUT

IN

OUT

IN

OUT

IN

OUT

IN

OUT

IN

OUT

IN

SIGNAL GND

 FRONT

SURROUND CENTER

SUB WOOFER

SUB WOOFER

AUDIO

IN

VIDEO

IN

VIDEO

IN

VIDEO

VIDEO

OUT

IN

OUT

IN

S2 VIDEO

IN

S2 VIDEO

IN

S2 VIDEO

S2 VIDEO

AUDIO

IN

AUDIO

AUDIO

 FRONT

SURROUND SURR BACK CENTER

SUB WOOFER

VIDEO

OUT

S2 VIDEO

OUT

VIDEO OUT

AUDIO

OUT

 FRONT

SURROUND SURR BACK

CENTER

TV/SAT IN DVD/LD IN MONITOR OUT

Y

P

B

/B-Y

P

R

/R-Y

75

COAXIAL

FM

AM

OUT

OUT

IN

STATUS IN

CONTROL S

wgwf wdws

w;

ql

wh

1

2

3 4 56 7

8 90

qa

qs

wa

qk

qj

qh

qg

qf

qd

1    DIGITAL jack

OPTICAL

CD/SACD IN
MD/DAT OUT
MD/DAT IN
TV/SAT IN
DVD/LD IN

COAXIAL

CD/SACD IN
DVD/LD IN

2

ANTENNA terminal
AM
FM

3

COMPONENT VIDEO jack
TV/SAT IN: Y,CB/B-Y,CR/R-Y
DVD/LD IN: Y,CB/B-Y,CR/R-Y
MONITOR OUT: Y,CB/B-Y,CR/R-Y

4

 MONITOR jack
CONTROL S IN (DA3ES, DA5ES model)
S2 VIDEO OUT
VIDEO OUT

5

TV/SAT jack
CONTROL S STATAS IN (DA3ES, DA5ES model)
S2 VIDEO IN
AUDIO IN

6

DVD/LD jack
CONTROL S OUT (DA3ES, DA5ES model)
 S2 VIDEO IN
VIDEO IN
AUDIO IN

7

VIDEO 2 jack
S2 VIDEO IN/OUT
VIDEO IN/OUT
AUDIO IN OUT

8

VIDEO 1 jack
CONTROL S IN/OUT
S2 VIDEO IN/OUT
VIDEO IN/OUT
AUDIO IN/OUT

9

CONTROL A1II jack

0

2ND ROOM jack
VIDEO OUT
AUDIO OUT

qa

SPEAKERS terminal
FRONT
SURROUND
CENTER
 SURR BACK

qs

AC OUTLET

qd

AC power cord (DA3ES model)

qf

AC INLET (DA5ES,VA555ES model)

qg

VOLTAGE SELECTOR switch (VA555ES: E model)

qh

IMPEDANCE SELECTOR switch

qj

SPEAKERS 3RD ROOM terminal (DA3ES, DA5ES model)

qk

 PRE OUT jack
FRONT
SURROUND
SURR BACK
SUB WOOFER
CENTER

ql

MULTI CHANNEL INPUT 1 jack
FRONT
SURROUND
SURR BACK
CENTER

w;

TAPE jack
IN/OUT

wa

 MULTI CHANNEL INPUT 2 jack
FRONT
SURROUND
CENTER
SUB WOOFER

ws

MD/DAT jack
IN/OUT

wd

CD/SACD IN jack

wf

SIGNAL GND

wg

RS232C connector

wh

 PHONO IN jack

10

All fluorescent segments are tested.  When this test is activated, all
segments turn on at the same time, then each segment turns on one
after another.
Procedure:
1. While depressing, the [DISPLAY] and the [ENTER] buttons

simultaneously, press the power  `/1  button to turn on the
main power.

2. All segments turn on at the same time, then each segment turns

on press the [DIMMER] button.

All preset contents are reset to the default setting.
Procedure:
Procedure:
1. While pressing [SET UP] and [DIMMER] buttons, press  `/1
     button, then “TUNER FACTORY PRESET” is displayed in
     several seconds and PRESET is complete.

Procedure:
1. Turn power off by pressing  `/1  button.
2. Hold down  `/1  button for 5 seconds, then “ENTER to Clear

All” is displayed.

3. Press  ENTER  button.
4. After “MEMORY CLEARING…” is displayed for a while,

“MEMORY CLEARED!” is displayed.

The preset sound field is cleared when this mode is activated.  Use
this mode before returning the product to clients upon completion
of repair.
Procedure:
1. While depressing the [MODE +] button, press the power `/1

button to turn on the main power.  The message S.F Initialize
appears and initialization is performed.

Either the 9 kHz step or 10 kHz step can be selected for the AM
channel step.
Procedure:
1. Set the FUNCTION to AM.  Turn off the main power.
2. While depressing the [TUNING +] button press the power  `/1

button to turn on the main power.

3. Either the message AM 9kHz Step or AM 10kHz Step appears.

Select the desired step.

Procedure:
1. Turn power on by pressing  `/1  button.
2. Press the [ENTER] and [SURROUND} buttons simultaneously,

then“MENU EXPAND” is displayed.

3. Press the [>] button several times to display “@@@@ ####

V.X.XX         ”.

@ : Model name
# : Destination
X : Version

: Sum value